C53035 - Internal Plumbing
Content
AW FACILITY MANAGEMENT SDN BHD (469194-V)
Preventive Maintenance & Routine Inspection
Asset Category: Revision No.: Originator: Name: Position: Internal Plumbing - Water Supply & Plumbing/ Semi Annually
Task No.: Work Group: Civil Date: Approved by: Name: Position:
Estimated PM Labour hours:
CAUTION: Ensure the stipulated safety procedures are followed while carrying out the PM activities
A.
Safety Precautions Prior to PM procedure : 1. Inform the concerned building/department well in advance 2. Use sign board
B.
Performance (Qualitative) Checklist : 1. Check the condition of the faucets, bib cocks and valves - leaking, dripping, operating properly 2. Check for timing/sensing on all automatic sink faucets 3. Check the conditions of sanitary fittings - wash basins, wash sinks, showers-bath tubs, urinals, water-closets/ flush cisterns 4. Check the flow/pressure from the faucets, bib cocks - choked, adequate 5. Check for the condition of the networking pipes and pipe fittings (tee's, elbows, bends, unions) - corroded, rusting, dripping/leaking at joints, loose joint fillers 6. Check the condition of the pipe supports - hangers, clamps - loose, fixed properly 7. Check for the insulation on the pipes. 8. Check the conditions of the drainage pipes and fittings - floor drains, waste couplings, clean-outs. 9. Check for leakage/dripping & blockage in the drainage pipes/fittings 10. Check for the grease traps and other trap fittings Checklist for Safety Inspection on Completion of PM: 1. Physical inspection for leakage from any pipes or fittings 2. 3. Quantitative/Inspection Checklist (record all measured data for the various parameters in space provided below ): Parameter: Set Limits: Data: F. Equipment/Test Apparatus Required: 1. Ladder 2.
C.
D.
E. Materials Required : 1. Adjustable wrench 2. Torch light
IMPORTANT: 1. No alterations or notes are allowed on this page. 2. Working copies shall be photocopied and stamped “WORKING COPY”. 3. This document is a Company property - it has been prepared solely for Company use. As such, this is not to be disclosed or distributed
Preventive Maintenance & Routine Inspection
Asset Category: Revision No.: Originator: Name: Position: Internal Plumbing - Water Supply & Plumbing/ Semi Annually
Task No.: Work Group: Civil Date: Approved by: Name: Position:
Estimated PM Labour hours:
CAUTION: Ensure the stipulated safety procedures are followed while carrying out the PM activities
A.
Safety Precautions Prior to PM procedure : 1. Inform the concerned building/department well in advance 2. Use sign board
B.
Performance (Qualitative) Checklist : 1. Check the condition of the faucets, bib cocks and valves - leaking, dripping, operating properly 2. Check for timing/sensing on all automatic sink faucets 3. Check the conditions of sanitary fittings - wash basins, wash sinks, showers-bath tubs, urinals, water-closets/ flush cisterns 4. Check the flow/pressure from the faucets, bib cocks - choked, adequate 5. Check for the condition of the networking pipes and pipe fittings (tee's, elbows, bends, unions) - corroded, rusting, dripping/leaking at joints, loose joint fillers 6. Check the condition of the pipe supports - hangers, clamps - loose, fixed properly 7. Check for the insulation on the pipes. 8. Check the conditions of the drainage pipes and fittings - floor drains, waste couplings, clean-outs. 9. Check for leakage/dripping & blockage in the drainage pipes/fittings 10. Check for the grease traps and other trap fittings Checklist for Safety Inspection on Completion of PM: 1. Physical inspection for leakage from any pipes or fittings 2. 3. Quantitative/Inspection Checklist (record all measured data for the various parameters in space provided below ): Parameter: Set Limits: Data: F. Equipment/Test Apparatus Required: 1. Ladder 2.
C.
D.
E. Materials Required : 1. Adjustable wrench 2. Torch light
IMPORTANT: 1. No alterations or notes are allowed on this page. 2. Working copies shall be photocopied and stamped “WORKING COPY”. 3. This document is a Company property - it has been prepared solely for Company use. As such, this is not to be disclosed or distributed
