Cosasco Access Fitting Protective Covers
Content
COSASCO®
Secondary Process Containment and Protective Covers
Secondary process containment and protective covers thread
onto the external thread of the access fitting body. For maximum
protection and safety, a wide range of covers are offered, from
lightweight polycarbonate to high pressure retaining, carbon
steel with pressure gauge and bleed plug.
High Pressure
Probe Adapter
Pressure Gauge
Bleed Plug
‘O’ Ring
4.50 in.
High Pressure Retaining Covers
Cosasco high pressure retaining covers with pressure gauge and
bleed plug offer both protection and an extra layer of safety with
a pressure rating of up to 10,000 PSI. A viton o‐ring creates a
tight seal retaining any pressure that may build up. The bleed
plug allows any pressure accumulation to be released prior to
the cover being backed off. The pressure gauge is used to
indicate if there is any pressure build up.
Heavy Duty Covers
Cosasco heavy duty covers are non‐pressure retaining, carbon
steel covers for use in areas where damage and impact is high
and extra protection of the access fitting is required.
High Pressure Retaining Cover
(10,000 PSI max.) with and without hole
Heavy Duty Cover
with and without hole
Light Duty Covers
Cosasco light duty covers are non‐pressure retaining,
polycarbonate covers for use in areas where damage is not likely
to occur. These are a lighter duty alternative to the standard
steel cover.
Light Duty Cover
with and without hole
Specifications
PART
HEIGHT
Inch cm
DIAMETER
Inch
cm
4.50
11.4
4.00
10.2
7.75 3.52
4.50
11.4
4.00
10.2
7.60 3.45
4.50
11.4
4.00
10.2
7.50 3.40
Carbon Steel
PROTECTIVE COVER WITHOUT HOLE
A non‐pressure retaining steel cover for use with
devices that do not require routine access to the
plug assembly (such as coupon holders).
3.75
9.5
3.25
8.3
2.5
1.59
Carbon Steel
PROTECTIVE COVER WITH HOLE
A non‐pressure retaining steel cover with an access
hole on the top for use with devices that require
routine access to the plug assembly (such as
corrosion monitoring probes).
2.25
5.7
3.25
8.3
2.0
0.91
206436
PROTECTIVE COVER WITHOUT HOLE
A non‐pressure retaining polycarbonate cover for
use with devices that do not require routine access
Polycarbonate
to the plug assembly (such as coupon holders). This
is a lighter duty alternative to the standard steel
cover.
3.6
9.0
3.5
8.9
0.50 0.22
206435
PROTECTIVE COVER WITH HOLE
A non‐pressure retaining polycarbonate cover with
an access hole on the top for use with devices that
Polycarbonate
require routine access to the plug assembly (such as
corrosion monitoring probes). This is a lighter duty
alternative to the standard steel cover.
2.3
5.7
3.5
8.9
0.40 0.18
PART NO.
MATERIAL
740090*
Carbon Steel
740093*
Carbon Steel
740095*
Carbon Steel
122734
DESCRIPTION
PRESSURE RETAINING COVER WITH BLEED PLUG,
PRESSURE GAUGE
10,000 PSI max.
A pressure retaining steel cover with an integral
bleed plug and 6000 psi pressure gauge. For use
with devices that do not require routine access to
the plug assembly (such as coupon holders).
PRESSURE RETAINING COVER WITH BLEED PLUG,
PRESSURE GAUGE AND ½” NPT CENTER HOLE FOR
STANDARD PROBE ADAPTER
2500 PSI max.
A pressure retaining steel cover with an integral
bleed plug and 3000 psi pressure gauge. This cover
has a ½” NPT in the top of the cover to
accommodate a standard (2500 PSI) pressure
retaining Probe Adapter
PRESSURE RETAINING COVER WITH BLEED PLUG,
PRESSURE GAUGE AND CENTER HOLE FOR HIGH
PRESSURE PROBE ADAPTER
10,000 PSI max.
A pressure retaining steel cover with an integral
bleed plug and pressure gauge. This cover has
center hole in the top of the cover to
accommodate a high pressure(10,000 PSI) retaining
Probe Adapter (must use high pressure probe
adapter)
WEIGHT
lb.
kg
122732
*Pressure retaining covers contain a standard Viton o‐ring. Optional seal materials are available by adding a seal code after the part
number. Also, alternate pressure gauge ratings are available by adding the pressure code after the part number. See ordering information
below.
Ordering Information
Material, Seal, and Pressure Gauge Ordering Options for Pressure Retaining Covers
Model
740090
740093
740095
Pressure Retaining Cover
Pressure Retaining Cover With Bleed Valve, Pressure Gauge
Pressure Retaining Cover With Bleed Valve, Pressure Gauge and 1/2" NPT Center Hole for Standard Probe Adapter
Pressure Retaining Cover With Bleed Valve, Pressure Gauge and Center Hole for High Pressure Probe Adapter
Code
XXXXXX
740090
Body Material
Enter UNS Number (omit for standard Carbon Steel)
Code
Seal Material Option (omit for standard Viton)
2
Ethylene Propylene
3
Kalrez
5
Epchlorohydrin
6
Nitrile
8
EDR Viton
A
B
HNBR EOL 101 O‐Ring Teflon Primary Packing ‐ * ‐13 to 320˚F (‐25 to 160˚C)
C
HNBR EOL 985 O‐Ring Teflon Primary Packing ‐ * ‐13 to 320˚F (‐25 to 160˚C)
AFLAS 36/90 O‐Ring Teflon Primary Packing ‐ * 32 to 392˚F (0 to 200˚C)
Code
Pressure Gauge Range
YYYY
Enter Pressure (psi) (omit for standard 6000 psi gauge on 740090 and 740095 covers or 3000 psi gauge
on 740093 cover)
S31600
2
Example
4000
Ordering Information
Material ordering option for Heavy Protective Covers
Model
122734
122732
Heavy Protective Cover
Protective Cover without Hole
Protective Cover with Hole
Code
Body Material Bo
XXXXXX
Enter UNS number (omit for standard Carbon Steel
122734
S31600
Example
Ordering options as part of an access fitting assembly
Pressure Retaining Covers:
-10
-11 /XXXXXX/Y/YYYY
-12
Pressure Gage Range
Seal Material Option
Cover Material UNS Number
Heavy Thread Protectors:
-1 /XXXXXX
-2
Cover Material UNS Number
Note: Only add option codes to specify non‐standard options. Omit codes for standard options.
Rohrback Cosasco Systems
11841 East Smith Avenue
Santa Fe Springs, CA 90670, USA
Tel: 1‐562‐949‐0123
Email: [email protected]
Web Site: www.cosasco.com
Bulletin #623‐D Rev. Date: 11/11/2015
©Rohrback Cosasco Systems, Inc. All rights reserved
The contents of this publication are presented for information purposes only, and while effort has been made to ensure their accuracy, they
are not to be construed as warranties or guarantees, express or implied, regarding the products or services described wherein or their use or
applicability. We reserve the right to modify or improve the designs or specifications of our products at any time without notice.
Rohrback Cosasco Systems Corrosion Monitoring Equipment is manufactured and sold under one or more of the following US Patents:
4138878, 4238298, 4338563, 4514681, 4537071, 4587479, 4605626, 4625557, 4755744, 4839580, 4841787, 4882537 5243297
Secondary Process Containment and Protective Covers
Secondary process containment and protective covers thread
onto the external thread of the access fitting body. For maximum
protection and safety, a wide range of covers are offered, from
lightweight polycarbonate to high pressure retaining, carbon
steel with pressure gauge and bleed plug.
High Pressure
Probe Adapter
Pressure Gauge
Bleed Plug
‘O’ Ring
4.50 in.
High Pressure Retaining Covers
Cosasco high pressure retaining covers with pressure gauge and
bleed plug offer both protection and an extra layer of safety with
a pressure rating of up to 10,000 PSI. A viton o‐ring creates a
tight seal retaining any pressure that may build up. The bleed
plug allows any pressure accumulation to be released prior to
the cover being backed off. The pressure gauge is used to
indicate if there is any pressure build up.
Heavy Duty Covers
Cosasco heavy duty covers are non‐pressure retaining, carbon
steel covers for use in areas where damage and impact is high
and extra protection of the access fitting is required.
High Pressure Retaining Cover
(10,000 PSI max.) with and without hole
Heavy Duty Cover
with and without hole
Light Duty Covers
Cosasco light duty covers are non‐pressure retaining,
polycarbonate covers for use in areas where damage is not likely
to occur. These are a lighter duty alternative to the standard
steel cover.
Light Duty Cover
with and without hole
Specifications
PART
HEIGHT
Inch cm
DIAMETER
Inch
cm
4.50
11.4
4.00
10.2
7.75 3.52
4.50
11.4
4.00
10.2
7.60 3.45
4.50
11.4
4.00
10.2
7.50 3.40
Carbon Steel
PROTECTIVE COVER WITHOUT HOLE
A non‐pressure retaining steel cover for use with
devices that do not require routine access to the
plug assembly (such as coupon holders).
3.75
9.5
3.25
8.3
2.5
1.59
Carbon Steel
PROTECTIVE COVER WITH HOLE
A non‐pressure retaining steel cover with an access
hole on the top for use with devices that require
routine access to the plug assembly (such as
corrosion monitoring probes).
2.25
5.7
3.25
8.3
2.0
0.91
206436
PROTECTIVE COVER WITHOUT HOLE
A non‐pressure retaining polycarbonate cover for
use with devices that do not require routine access
Polycarbonate
to the plug assembly (such as coupon holders). This
is a lighter duty alternative to the standard steel
cover.
3.6
9.0
3.5
8.9
0.50 0.22
206435
PROTECTIVE COVER WITH HOLE
A non‐pressure retaining polycarbonate cover with
an access hole on the top for use with devices that
Polycarbonate
require routine access to the plug assembly (such as
corrosion monitoring probes). This is a lighter duty
alternative to the standard steel cover.
2.3
5.7
3.5
8.9
0.40 0.18
PART NO.
MATERIAL
740090*
Carbon Steel
740093*
Carbon Steel
740095*
Carbon Steel
122734
DESCRIPTION
PRESSURE RETAINING COVER WITH BLEED PLUG,
PRESSURE GAUGE
10,000 PSI max.
A pressure retaining steel cover with an integral
bleed plug and 6000 psi pressure gauge. For use
with devices that do not require routine access to
the plug assembly (such as coupon holders).
PRESSURE RETAINING COVER WITH BLEED PLUG,
PRESSURE GAUGE AND ½” NPT CENTER HOLE FOR
STANDARD PROBE ADAPTER
2500 PSI max.
A pressure retaining steel cover with an integral
bleed plug and 3000 psi pressure gauge. This cover
has a ½” NPT in the top of the cover to
accommodate a standard (2500 PSI) pressure
retaining Probe Adapter
PRESSURE RETAINING COVER WITH BLEED PLUG,
PRESSURE GAUGE AND CENTER HOLE FOR HIGH
PRESSURE PROBE ADAPTER
10,000 PSI max.
A pressure retaining steel cover with an integral
bleed plug and pressure gauge. This cover has
center hole in the top of the cover to
accommodate a high pressure(10,000 PSI) retaining
Probe Adapter (must use high pressure probe
adapter)
WEIGHT
lb.
kg
122732
*Pressure retaining covers contain a standard Viton o‐ring. Optional seal materials are available by adding a seal code after the part
number. Also, alternate pressure gauge ratings are available by adding the pressure code after the part number. See ordering information
below.
Ordering Information
Material, Seal, and Pressure Gauge Ordering Options for Pressure Retaining Covers
Model
740090
740093
740095
Pressure Retaining Cover
Pressure Retaining Cover With Bleed Valve, Pressure Gauge
Pressure Retaining Cover With Bleed Valve, Pressure Gauge and 1/2" NPT Center Hole for Standard Probe Adapter
Pressure Retaining Cover With Bleed Valve, Pressure Gauge and Center Hole for High Pressure Probe Adapter
Code
XXXXXX
740090
Body Material
Enter UNS Number (omit for standard Carbon Steel)
Code
Seal Material Option (omit for standard Viton)
2
Ethylene Propylene
3
Kalrez
5
Epchlorohydrin
6
Nitrile
8
EDR Viton
A
B
HNBR EOL 101 O‐Ring Teflon Primary Packing ‐ * ‐13 to 320˚F (‐25 to 160˚C)
C
HNBR EOL 985 O‐Ring Teflon Primary Packing ‐ * ‐13 to 320˚F (‐25 to 160˚C)
AFLAS 36/90 O‐Ring Teflon Primary Packing ‐ * 32 to 392˚F (0 to 200˚C)
Code
Pressure Gauge Range
YYYY
Enter Pressure (psi) (omit for standard 6000 psi gauge on 740090 and 740095 covers or 3000 psi gauge
on 740093 cover)
S31600
2
Example
4000
Ordering Information
Material ordering option for Heavy Protective Covers
Model
122734
122732
Heavy Protective Cover
Protective Cover without Hole
Protective Cover with Hole
Code
Body Material Bo
XXXXXX
Enter UNS number (omit for standard Carbon Steel
122734
S31600
Example
Ordering options as part of an access fitting assembly
Pressure Retaining Covers:
-10
-11 /XXXXXX/Y/YYYY
-12
Pressure Gage Range
Seal Material Option
Cover Material UNS Number
Heavy Thread Protectors:
-1 /XXXXXX
-2
Cover Material UNS Number
Note: Only add option codes to specify non‐standard options. Omit codes for standard options.
Rohrback Cosasco Systems
11841 East Smith Avenue
Santa Fe Springs, CA 90670, USA
Tel: 1‐562‐949‐0123
Email: [email protected]
Web Site: www.cosasco.com
Bulletin #623‐D Rev. Date: 11/11/2015
©Rohrback Cosasco Systems, Inc. All rights reserved
The contents of this publication are presented for information purposes only, and while effort has been made to ensure their accuracy, they
are not to be construed as warranties or guarantees, express or implied, regarding the products or services described wherein or their use or
applicability. We reserve the right to modify or improve the designs or specifications of our products at any time without notice.
Rohrback Cosasco Systems Corrosion Monitoring Equipment is manufactured and sold under one or more of the following US Patents:
4138878, 4238298, 4338563, 4514681, 4537071, 4587479, 4605626, 4625557, 4755744, 4839580, 4841787, 4882537 5243297
