Drill Pipe Float Valves

Published on June 2016 | Categories: Documents | Downloads: 137 | Comments: 0 | Views: 770
of 45
Download PDF   Embed   Report

Comments

Content

INTRODUCTION DRILL PIPE FLOAT VALVES INTRODUCTION

Baker SPD

Baker SPD is known as the leading manufacturer of Drill Pipe Float Valves in the industry. Committed to continuous improvement and production of quality products for optimum performance and reliability, the Drill Pipe Float Valves have become an industry standard due to their superior engineering, quality, construction, and dependability in service. Baker SPD manufactures a complete line of float valves, repair kits, and puller assemblies to accommodate a wide range of drilling situations and operating conditions, including H2S and steam service. These Drill Pipe Float Valves provide added blowout protection at the bottom of the drillstring, prevent flowback when joints are added, and keep cuttings out of the drillpipe to prevent bit plugging while making connections. Note: It is recommended that multiple Drill Pipe Float Valves run in the same string be separated.

DRILL PIPE FLOAT VALVES

QUALITY CONSTRUCTION
Baker SPD Drill Pipe Float Valves have been designed, manufactured, tested, and certified in accordance with accepted engineering, manufacturing, and quality assurance standards including, but not limited to, the following documents or publications: American Iron and Steel Institute (AISI) American National Standards Institute (ANSI) American Society for Testing and Materials (ASTM) American Society for Metals (ASM) American Welding Society (AWS) Rubber Manufacturer’s Association (RMA) Society of Automotive Engineers (SAE)

TEST PRESSURE RATINGS
Model F Drill Pipe Float Valves rated 7,500 WP. Model G Drill Pipe Float Valves rated 7,500 WP.

CAGES
Cage construction of the various Models F and G includes ductile iron and low carbon steel on the 6F size only. Hardness levels of these materials are at or below 22 Rockwell C to resist hydrogen sulfide stress cracking when used for H2S applications. Stainless Steel available upon request. Alloy Steel available in Model F only.

SPRINGS
Models F and G utilize tempered “spring steel” springs for normal operating conditions or high alloy springs for H2S and steam applications.

SEAL AND SHOCK ABSORBERS
Temperature Rating Description Product Family No.
;For

Standard 250°F Buna-N H48013 thru H48019

H 2S 450°F Viton® H48030 thru H48033

Steam; 500°F EPDM H48020 thru H48026

steam applications only where no hydrocarbons are present.

39

Baker SPD
BAKER SPD MODEL F VALVES
BENEFITS AND FEATURES

MODEL F DRILL PIPE FLOAT VALVES

A fast-acting plunger valve opens when the kelly is pulled out of the hole, then closes, eliminating breakage of a wet joint. The plunger type valve also prevents flowback when adding joints and keeps cuttings out of the drill pipe, preventing bit plugging while making connections. The likelihood of having to pull a wet string with its attendant safety hazards and expensive down time is eliminated.

CONSTRUCTED FOR LONG LIFE
Models F and FC Drill Pipe Float Valves are made of low carbon steel suitable for most applications including H2S conditions. It is designed and constructed with minimum number of parts-all highly resistant to wear to give long trouble-free service.

EASILY SERVICED
Normally, the only service required is replacement of the valve seal. This can be accomplished in seconds without special tools. The valve guide at the lower end of the valve stem is simply raised, compressing the spring and allowing for removal of the entire inner portion of the valve. Baker SPD Drill Pipe Float Valves are easily installed by simply lubricating the side seals and sliding them into the cavity in the float sub or drilled out drill collar. Care must be taken in positioning the float valve in the drilling string. If it is placed too far from the top of the hole and the pipe is not filled while running in, hydrostatic pressure could cause damage to the drill pipe or the float valve. If the pipe is filled while running in, the float valve can be placed just above the bit, if desired.

BAKER SPD NOW OFFERS TWO NEW DRILL PIPE FLOAT VALVE CONFIGURATIONS
The Model FA offers all the standard features of the Model F Float Valve with the added feature of a port which allows a fluid path through the center of the valve. This feature allows for an automatic partial filling of the drill pipe during run in. This valve is used when monitoring the bit head for gas pressure and/or gas pockets, allowing measurement of differential pressure when required. The Model FA is available in all sizes. The Model FI also offers all the standard features of the Model F Float Valve with the added feature of an integral baffle plate at the top of the float valve. For operations where a baffle plate is always used for instrumentation or fluid control the integral baffle plate configuration offers and economical option. The Model FI is only available in sizes 4R and 5F-6R.

Model FA Float Valve

Model FI Float Valve

40

MODEL F DRILL PIPE FLOAT VALVES MODEL F PLUNGER TYPE VALVE
Product Family Nos. H48013 and H48043 (Heavy Duty) The Model F Plunger Type Valve provides positive and instantaneous shut off against high or low pressure, assuring continuous control of fluid flow during drilling. For normal drilling operations, the durable Model F is the most economical choice and is available in all sizes. The “Heavy Duty” Model F Drill Pipe Float Valve is designed with a high alloy steel body that increases the lift of the Drill Pipe Float Valve. It provides high impact resistance and is dimensionally identical to the standard Baker Drill Pipe Float Valve, allowing interchangeability of the trim. This type of Drill Pipe Float Valve is recommended for use with downhole mud motors. Note: Not recommended for Air Drilling.

Baker SPD
7

3

2 1

DRILL PIPE FLOAT VALVES

4

6

5

Diagram Key for Model F Plunger Type Valve
1. Valve Seal Disc 2. Plunger/Valve 3. Side Seal 4. Valve Seal 5. Guide 6. Spring 7. Cage
Model F Plunger Type Valve Product Family No. H48013

MODEL FC AUTOMATIC FILL VALVE
Product Family No. H48018 The Model FC Automatic Fill Valve is ideal to use when drilling deep wells. The automatic feature on the Model FC allows the drillpipe to fill from the bottom, thereby removing the mess, hazards, and lost time from filling. When running in the hole, the automatic fill feature eliminates the “ram effect” preventing the downhole pressure surges that can cause formation damage. The Model FC is slotted on the stem to accept a low carbon “automatic fill” key assembly that is automatically released by fluid circulation releasing the plunger for complete closure. Note: Not recommended for Air Drilling.

l

2

3

4

5 6

7 1

Diagram Key for Model FC Automatic Fill Valve
8

1. Guide 2. Cage 3. Side Seal 4. Plunger/Valve

5. Valve Seal 6. Valve Seal Disk 7. Spring 8. Key

Model FC Automatic Fill Valve Product Family No. H48018

41

Baker SPD
BAKER SPD MODEL G VALVES
BENEFITS AND FEATURES

MODEL G DRILL PIPE FLOAT VALVES

Flapper Valves for G Models are made of normalized, carburized, quenched, and tempered alloy steel to resist wear and erosion. The flapper valve opens fully during circulation providing an unrestricted bore through the valve thereby effectively prolonging the life of the valve and drill collar as there is no diversion of fluid against the drill collar ID.

CONSTRUCTED FOR LONG LIFE
Dampeners have been provided at the three most common points of wear due to vibration. The shock absorber has been placed at the bottom of the valve cage to prevent valve to bit wear. The flapper valve is provided with a resilient bumper to prevent wear between it and the valve cage or drill collar ID. The hinge pin is coated to protect against wear from vibration. Like all Baker SPD Drill Pipe Float Valves, G Models are designed for long life, fast installation, (no tools are required), and trouble free operation.

EASILY SERVICED
Particular attention should be given to the hinge pin, spring, and rubber parts. Since the seal is not in the fluid flow pattern it receives little wear and seldom is replaced. When replacing the seal, the handle of the float valve puller may be used to remove the seal retainer, and after installation of a new seal, used to reinstall the seal retainer. To remove, insert the handle of the float valve puller into the upper end until the beveled edge of the handle seats on the beveled edge of the seal retainer. The seal retainer can then be knocked out. In this instance, the seal retainer should also be replaced. Note: Caution should be used to prevent the valve face from being damaged.

42

MODEL G AND GA DRILL PIPE FLOAT VALVE MODEL G FULL OPEN VALVE (FLAPPER TYPE)
Product Family No. H48015 The Model G “Flapper Type” Full Open Valve incorporates a specially designed flapper which opens quickly and fully to provide a completely unrestricted bore through the valve. The Model G is especially good for use with highly abrasive fluids. When circulation stops, the flapper closes instantly to prevent cuttings from entering the drill string and plugging the bit. The valve opens when the first joint is raised out of the hole assuring the first joints drain and are not pulled wet. This saves mud and avoids safety hazards and down time. The flapper-type valve complements primary blowout prevention equipment to provide complete internal pressure control.

Baker SPD

10

9

1 2 3 4 8 7 6

DRILL PIPE FLOAT VALVES

Diagram Key for Model G Full Open Valve (Flapper Type)
1. Small Bumper 2. Spring 3. Pin 4. Large Bumper 5. Shock Absorber 6. Seal Retainer 7. Flapper Valve 8. Seal 9. Side Seal 10. Cage

5 Model G Full Open Valve (Flapper Type) Product Family No. H48015

MODEL GA DIFFERENTIAL PRESSURE MONITORING VALVE
Product Family No. H48016 The Model GA Differential Pressure Monitoring Valve is identical to the Model G except for a hardened 1/4 in. diameter tungsten carbide orifice bean insert in the flapper to provide automatic partial filling of the drillpipe during running in. This valve is used when monitoring the bit head for gas pressure and/or gas pockets, allowing measurement of differential pressure when required.

11

10 1 2 3 4

9 8

Diagram Key for Model GA Differential Pressure Monitoring Valve
1. Small Bumper 2. Spring 3. Pin 4. Large Bumper 5. Flapper Valve 6. Shock Absorber 7. Carbide Bean 8. Seal Retainer 9. Seal 10. Side Seal 11. Cage

5

7

6 Model GA Differential Pressure Monitoring Valve Product Family No. H48016

43

Baker SPD
11

MODEL GC AND GCA DRILL PIPE FLOAT VALVES MODEL GC AUTOMATIC FILL FLAPPER VALVE
Product Family No. H48019 The Model GC Automatic Fill Flapper Valve uses a low carbon steel “automatic fill” key assembly that allows the pipe to fill from the bottom, reducing run in time by eliminating the need to fill the string from the top. When running in the hole, the automatic fill feature eliminates the “ram effect” preventing the downhole pressure surges that can cause formation damage. The valve can be run in either the closed position or the automatic fill position. The fast acting flapper valve opens when the kelly is pulled out of the hole reducing the possibility of pulling a wet string along with the associated safety hazards. Mud spill-over on the rig floor is also eliminated. These timesaving features allow the Model GC to quickly pay for itself.

10

1 2 3 4 5 6 9 8

Diagram Key for Model GC Automatic Fill Flapper Valve
7 Model GC Automatic Fill Flapper Valve Product Family No. H48019

1. Small Bumper 2. Seal Retainer 3. Seal 4. Pin 5. Spring 6. Large Bumper

7. Shock Absorber 8. Key 9. Flapper Valve 10. Side Seal 11. Cage

11

10

MODEL GCA AUTOMATIC FILL WITH DIFFERENTIAL PRESSURE MONITORING VALVE
Product Family No. H48019 The Model GCA Automatic Fill with Differential Pressure Monitoring Valve incorporates the benefits of the Models GC and GA, allowing automatic partial filling of the drillpipe from the bottom, eliminating the need to fill the string from the top when running in the hole and measuring differential pressures when required.

1 2 3 4 5 6 12 9 8

Diagram Key for Model GCA Automatic Fill with Differential Pressure Monitoring Valve
1. Small Bumper 2. Seal Retainer 3. Seal 4. Pin 5. Spring 6. Large Bumper 7. Shock Absorber 8. Key 9. Carbide Bean 10. Side Seal 11. Cage 12. Flapper Valve

7 Model GCA Automatic Fill with Differential Pressure Monitoring Valve Product Family No. H48019

44

MODEL GB AND GBA DRILL PIPE FLOAT VALVES MODEL GB AIR DRILLING VALVE
Product Family No. H48017 The Model GB Air Drilling Valve is designed for air drilling only. It is identical to the Model G except the spring has been removed and the beveled design of the guide greatly reduces the danger of hanging up on the float valve when retrieving tools below it.
2 1

Baker SPD

3

4

Special Installation
The Drill Pipe Float Valve is installed near the top of the drillstring. Escaping air is channeled under the flapper valve, forcing it closed, and preventing loss of pressure. Note: In order to lose as little air as possible from the drillstring when a joint is made up, it is recommended that the float valve be moved up in the drillstring each time a new bit is installed. Caution must be exercised, however, to keep the valve at least one joint below the kelly; otherwise, the valve could be blown out of the drillpipe by trapped pressure when the kelly is removed.
5

DRILL PIPE FLOAT VALVES

6

8

7

Diagram Key for Model GB Air Drilling Valve
1. Cage 2. Side Seal 3. Seal Retainer 4. Seal 5. Pin 6. Flapper Valve 7. Shock Absorber 8. Location of Bevel Guide
Model GB Air Drilling Valve Product Family No. H48017

MODEL GBA AIR DRILLING WITH DIFFERENTIAL PRESSURE MONITORING VALVE
Product Family No. H48017 The Model GBA Air Drilling Valve with Differential Pressure Monitoring Valve incorporates the benefits of the Models GB and GA. The bevel design of the guide reduces the danger of hanging up on the float valve when retrieving tools. The 1/4 in. diameter tungsten carbide orifice bean insert in the flapper allows monitoring of differential pressure.

1

9

2

3

4

Diagram Key for Model GBA Air Drilling With Differential Pressure Monitoring Valve
1. Cage 2. Seal Retainer 3. Seal 4. Pin 5. Flapper Valve 6. Carbide Bean 7. Shock Absorber 8. Location of Bevel Guide 9. Side Seal

5 6

8

7 Model GBA Air Drilling With Differential Pressure Monitoring Valve Product Family No. H48017

45

Baker SPD

MODELS GS AND GAS DRILL PIPE FLOAT VALVES MODELS GS AND GAS DRILL PIPE FLOAT VALVES
Product Family Nos. H48058 and H48059 (Model GS); H48056 and H48057 (Model GAS)
Baker SPD now offers two new designs in its Drill Pipe Float Valve product line. The Model GS and GAS Drill Pipe Float Valves offer optimum performance and reliability for jobs that require high flow and erosion resistance. Made of alloy steel tempered for H2S applications, the GS and GAS feature a unique flapper relief to reduce flapper spring and pin wear. The Model GS is provided with a non ported flapper and the Model GAS has a ported flapper. Model GS and GAS are available in four Drill Pipe Float Valve standard configurations as noted in the table below. There are also three non standard configuration; 3.38 x 2, 4F Short, and 4.8 x 2.94. The nonstandard sizes offer maximized flow areas with a compact length for drill motor applications. The Model GS and GAS valves are machined to strict tolerances with a large ID to provide high flow rates and flapper valve relief in the cage to minimize fluid wear and streamline flow.
8 9

Models GS and GAS Drill Pipe Float Valves Product Family Nos. H48058, H48059, H48056, and H48057

2 3

7 4

• Option: Tungsten carbide coating on flapper face for Model GS and Model GAS • Machined to strict tolerances to allow O-ring seal (Model GAS only) • Machined to strict tolerances to allow for standard seals (Model GS only) • Eliminates wear on Bit Sub, Hinge Pins, and Flapper • Reduced flow restrictions

Diagram Key for Model GAS
5 1 6

1. Cage 2. Seal Retaining Ring 3. Seal 4. Pin 5. Flapper Valve

6. Carbide Bean (GAS Only) 7. Spring 8. Back-up Spiral Ring 9. O-ring

Model GAS Mud Motor Drill Pipe Float Valve Product Family Nos. H48056 and H48057

MODELS GS AND GAS DRILL PIPE FLOAT VALVES DIMENSIONAL DATA
Model GS, GAS Valve Size 3.38 x 2 3-1/2 IF 4R 4F Short 5R 4.8 x 2.94 5F6R Model GS, GAS ID of Valve 2.00 1.69 2.00 2.25 2.69 2.94 2.98 D Diameter of Valve 3.365 3.125 3.469 3.656 3.875 4.805 4.781 R (D + 1/32) Diameter of Recess for Valve 3.397 3.156 3.500 3.688 3.907 4.813 4.813 L Length of Valve 6.00 10.00 8.31 7.75 9.75 7.0 11.75

46

H2S/STEAM SERVICE VALVES H2S SERVICE
FEATURES AND BENEFITS

Baker SPD

The H2S service valve is made of AISI 1018/1020 Steel. Cages are made of ASTM A-395 Ductile Iron, and springs are made of UNS #N07750 (High Alloy). Elastomers provide protection up to 450°F. All elastomers are made of Viton® which performs well where H2S and hydrocarbons are present.

MODEL F DRILL PIPE FLOAT VALVE
Product Family Nos. H48030 (Model F) and H48032 (Model FC) The Model F Drill Pipe Float Valve for H2S service, provides instantaneous shut-off against high or low pressure, assuring control of the fluid flow through the drilling string at all times during the drilling operation whether the kelly is in place or not.
DRILL PIPE FLOAT VALVES

MODEL G DRILL PIPE FLOAT VALVE
Product Family Nos. H48031 (Model G) and H48033 (Model GC) The Model G Drill Pipe Float Valve for H2S service, provides instantaneous shut-off against either liquid or gas preventing entry of cuttings into the drillpipe when circulating is discontinued.

STEAM SERVICE
FEATURES AND BENEFITS
The Steam service valve is made of AISI 1018/1020 Steel. Cages are made of ASTM A-395 Ductile Iron, and springs are made of UNS #N07750 (High Alloy). Elastomers provide protection up to 500°F. All elastomers are made of EPDM which performs well in steam where hydrocarbons are not present.

MODEL F DRILL PIPE FLOAT VALVE
Product Family No. H48020 The Model F Drill Pipe Float Valve for steam service provides instantaneous shut-off against high or low pressure, assuring control of the fluid flow through the drillstring at all times during the drilling operation - whether the kelly is in place or not.

MODEL G DRILL PIPE FLOAT VALVE
Product Family Nos. H48021 (Model G) and H48023 (Models GB and GBA) The Model G Drill Pipe Float Valve for steam service provides instantaneous shut-off against either liquid or gas preventing entry of cuttings into the drillpipe when circulating is discontinued.

FLOAT VALVE INSTALLATION
Baker SPD Drill Pipe Float Valves are easily installed by simply lubricating the side seals and sliding them into the cavity in the float sub or drilled-out drill collar. Installed in the float sub, the valve may be positioned between tool joints or by inverting the float sub between the bit and drill collar. Care must be taken in positioning the float valve in the drillstring. If it is placed too far from the top of the hole and the pipe is not filled while running in, hydrostatic pressure can cause damage to the drillpipe or the float valve. If the pipe is filled while running in, the float valve can be placed just above the bit.

SPECIAL INSTRUCTIONS FOR MODEL GB DRILL PIPE FLOAT VALVE
Install the Model GB Drill Pipe Float Valve near the top of the drillstring where escaping air is channeled under the flapper valve, forcing it closed and preventing loss of pressure.

47

Baker SPD
REPAIR KITS

REPAIR KITS

Specially packaged repair kits are available for all Baker SPD Drill Pipe Float Valves as follows:

REPAIR KITS FOR ALL STYLES OF MODEL F DRILL PIPE FLOAT VALVES
1

3 1 2 4 2

METAL KIT for Model F Drill Pipe Float Valves contain:
1. 2. 3. 4. Three [3] Valve Springs One [1] Valve Guide One [1] Valve Seal Disk One [1] Valve

RUBBER KIT for Model F Drill Pipe Float Valves contain:
1. Eight [8] Side Seals 2. Two [2] Valve Seals (Four Redressings) Note: Also available for single redressing.

(Three Redressings) Note: Also available for single redressing.

REPAIR KITS FOR ALL STYLES OF MODEL G DRILL PIPE FLOAT VALVES

2

1

3 1 4 2 3 4

METAL KIT for Model G Drill Pipe Float Valves contain:
1. 2. 3. 4. One [1] Seal Retaining Ring Three [3] Hinge Pins Three [3] Spring Assemblies One [1] Flapper Valve

RUBBER KIT for Model G Drill Pipe Float Valves contain:
1. 2. 3. 4. Eight [8] Side Seals One [1] Seal Retaining Ring One [1] Shock Absorber Two [2] Valve Seals

(Three Redressings) Note: Also available for single redressing. 48

(Four Redressings) Note: Also available for single redressing.

TOOLS TOOLS VALVE PULLERS FOR ALL STYLES OF MODEL F DRILL PIPE FLOAT VALVES
Product Family No. H48091 The valve puller consists of a finger sub that is stabbed into the bottom end of the Drill Pipe Float Valve cage and engages the web by right-hand rotation.

Baker SPD

1

2

DRILL PIPE FLOAT VALVES

Caution: When pulling a Model FC, the release key on the Drill Pipe Float Valves must be positioned such that the finger sub does not contact the key prior to engaging the web of the cage. This will prevent damage to the key during valve removal.

Diagram Key for Valve Puller for All Styles of Model F Drill Pipe Float Valves
1. 2. 3. 4. 5. Handle Stop Stem Hammer Finger Sub

3

4

5 Valve Puller for F Models Product Family No. H48091

VALVE PULLERS FOR ALL STYLES OF MODEL G DRILL PIPE FLOAT VALVES
Product Family No. H48090 The valve puller consists of a fork that engages the cage of the Drill Pipe Float Valve. The driver is then forcefully pulled upward to quickly and easily remove the valve from the cavity in the float sub or drill collar.

1

Diagram Key for Valve Puller for All Styles of Model G Drill Pipe Float Valves
1. Driver 2. Fork

2 Valve Puller for G Models Product Family No. H48090

BAFFLE PLATES
Product Family No. WVT791 Baker SPD Baffle Plates are installed on top of the Drill Pipe Float Valve as a landing tool for recorders, thus preventing the recorder from entering the drillpipe float valve and possibly the drill bit.

Baffle Plates Product Family No. WVT791

49

Baker SPD

DIMENSIONAL INFORMATION

DIMENSIONAL INFORMATION FOR ALL STYLES OF MODEL F AND G DRILL PIPE FLOAT VALVES

L

L

T+ 1/32" -0

R+ 1/64" -0

3 ±1/16"

A ±1/16"

A = L (Length of Valve Assembly) + Length of Tool Joint Pin + 1/4 in.)
D D

MODELS F AND G DRILL PIPE FLOAT VALVE DIMENSIONAL DATA
Valve Size 1R 1F-2R 2F-3R 3F 3-1/2 IF 4R 4F 5R 5F-6R 6F D Diameter of Valve 1-21/32 1-29/32 2-13/32 2-13/16 3-1/8 3-15/32 3-21/32 3-7/8 4-25/32 5-11/16 R (D + 1/32) Diameter of Recess for Valve 1-11/16 1-15/16 2-7/16 2-27/32 3-5/32 3-1/2 3-11/16 3-29/32 4-13/16 5-23/32 L Length of Valve 5-7/8 6-1/4 6-1/2 10 8-5/16 12 9-3/4 11-3/4 14-5/8 T; Diameter of Recess for Baffle Plate 1-5/16 1-1/2 1-29/32 2-7/16 2-11/16 2-15/16 3-1/4 3-3/8 4-9/32 5-3/16 ID of Valve Model F 1 1-1/4 1-9/16 1-7/8 2-5/16 2-1/2 2-3/4 3-1/4 4-1/8 Model G N/A 1 1-1/4 1-5/8 1-31/32 2-3/16 2-1/4 2-7/8 N/A

;Disregard if this diameter is the same or smaller than standard tool joint ID. Note: The Dimensional Information Chart is not for Models GS and GAS Drill Pipe Float Valves. N/A = Non-Applicable.

RECUTTING BODY OR BORING OUT DRILL COLLARS
Models F and G Drill Pipe Float Valves are identical in outside dimensions and use the same float sub or boredout drill collar. Float subs are made in lengths from 14 in. to 30 in. depending on size and type, and designed for two recuts, two on either end or one on each end. Each time the tool joint box is recut, however, the shoulder of the lower end of the body bore must be cut back to maintain dimension “A”. The body bore length permits approximately 1/4 in. travel of the valve, and this travel should be maintained when the body is recut. Bodies longer than the standard 3 ft in length allow more recuts and can be furnished on special order.

50

BIT SUB INFORMATION
BIT SUB INFORMATION
Valve Size 1R 1F-2R 2F-3R 4R 5R 5F-6R 5F-6R 6F 3F 3-1/2 IF 4F 5F-6R 6F 1F-2R 2F-3R 3-1/2 IF 4F 5R 5F-6R 6F Threads in. 2-3/8 2-7/8 3-1/2 4-1/2 5-1/2 6-5/8 7-5/8 8-5/8 3-1/2 4 4-1/2 5-1/2 6-5/8 2-3/8 2-7/8 3-1/2 4 4-1/2 5-1/2 6-5/8 Tool Joint Type STD/OD in. 3-1/8 3-3/4 4-1/4 5-1/2 6-3/4 7-3/4 8-7/8 10 4-5/8 5-1/4 5-3/4 7 8 3-3/8 4-1/8 4-3/4 5-3/4 6-3/8 7-3/8 8-3/4

Baker SPD

Face-to-Shoulder or Face-to-Face in. 18 20 24 28 30 24 28 30 18 20 24 28 30
DRILL PIPE FLOAT VALVES

API Regular

API Full Hole

API IF API IF Box x Pin

API IF

Note: Box and/or pin specification required. Note: The box and/or pin connections on Drill Pipe Float Subs should not be mated with old tool joints. In addition, the sub should not be made up in the top of a drill collar unless the box on the drill collar has been machined beforehand and new joints placed on the drill collar to mate with the upper box connection in the Drill Pipe Float Sub. Note: Other sizes are provided upon request.

51

Baker SPD
SPECIFICATION GUIDE
Tool Joint Types API Regular Hughes or Reed Acme Regular Union Tool Hughes or Reed Double Streamline API Full Hole Reed Acme Full Hole Hughes Acme Streamline Hughes Xtra Hole Reed Semi-Internal Flush API Internal Flush Hydril Type “IF” (Internal Flush Ext Upset) Hydril “EIU” (External Internal Upset) Hydril Type “F” 2-7/8 (External Flush) 3-1/2; Hughes Ext Flush Acme Type Hughes Ext Flush Full Hole Type 2-3/8 2-3/8; 1R 2-3/8 2-3/8 2-3/8 1F-2R 2-7/8 2-7/8 2-7/8 3-1/2 2-7/8 2-3/8 2-3/8 2F-3R 3-1/2 3-1/2 3F Sizes (in.) 3-1/2 IF 4R 4-1/2 4-1/2

SPECIFICATION GUIDE

4F

4-1/2 3-1/2 2-7/8 4 4-1/2 3-1/2 3-1/2; 5 4 4-1/2 4-1/2; 4-1/2; 4-1/2; 4-1/2 3-1/2 3-1/2; 3-1/2 4-1/2 5 4 5-1/2 5-9/16 5-1/2 5-9/16 4-1/2 4-1/2 4

5R 5F-6R 5-1/2 6-5/8 5-9/16; 7-5/8O 5-1/2 6-5/8 5-9/16 5-1/2 6-5/8O 5-9/16; 5-1/2 5-9/16; 5-1/2 5-9/16; 5-1/2 5-9/16; 5-1/2 5-9/16;

6F 8-5/8

6-5/8;

2-3/8

2-7/8 2-7/8 2-7/8 2-7/8 2-7/8;

3-1/2; 3-1/2 3-1/2

5 5 4-1/2 4-1/2;

5 5-1/2 5-9/16; 6-5/8

6-5/8 6-5/8

3-1/2

4-1/2 4-1/2

Shaded areas indicate sizes available in Models G, GA, GC, GCA, GB, and GBA. Model F available in all sizes. Model FC available in all sizes, except 1R and 1F-2R. ; Float sub in these sizes has smaller ID than standard tool joint. O Interchangeable.

BIT AND SHANK SIZES
Bit and Shank Sizes Bit Size 3-1/4 3-3/8 4-1/2 4-3/4 5-1/2 6 6-1/8 6-1/4 6-1/2 6-3/4 7-7/8 8-1/4 8-1/2 8-3/4 9-1/2 9-3/4 10-1/2 11 12-1/4 13-1/2 20 24 25 (in.) Std API Pin 2-3/8 2-3/8 2-3/8 2-7/8 3-1/2 3-1/2 3-1/2 3-1/2 3-1/2 3-1/2 4-1/2 4-1/2 4-1/2 4-1/2 6-5/8 6-5/8 6-5/8 6-5/8 6-5/8 6-5/8 7-5/8 7-5/8 7-5/8 Shank Size (in.)

52

ORDERING INFORMATION ORDERING INFORMATION (MATERIAL NUMBERS AND WEIGHTS)
Standard Service Drill Pipe Float Valves, Repair Kits, and Puller Assemblies MODEL F PLUNGER TYPE VALVE PRODUCT FAMILY NOS. H48013 (STANDARD STYLE) AND H48043 (HEAVY DUTY ALLOY STYLE)
Size 1R 1F-2R 2F-3R 3F 3-1/2 IF 4R 4F 5R 5F-6R 6F Assembly 480131200 480131422 480132432 480133400 480133600 480134200 480134400 480135200 480135462 480136400 Wt lb 1.5 1.5 2.5 5.0 5.0 7.0 9.5 9.5 16.0 28.0 Assembly N/A N/A 480432432 N/A 480433600 480434200 480434400 480435200 480435462 N/A Wt lb N/A N/A 2.5 N/A 5.0 7.0 9.5 9.5 16.0 N/A Rubber Repair Kit 016012200 016012300 016012400 016012500 016012600 016012700 016012800 016012900 016013000 016013100 Wt lb 0.5 0.7 0.8 1.0 1.0 1.0 1.0 1.0 1.1 2.0 Metal Repair Kit 015929800 016011300 016011400 016011500 016011500 016011700 016011800 016011900 016012000 016012100 Wt lb 1.0 2.0 2.0 2.0 2.0 2.0 3.0 4.0 5.0 5.0

Baker SPD

Puller Assembly 480911200 480911200 480912432 480913400 480913400 480914200 480914400 480915200 480915462 480916400

Wt lb 6.0 6.0 8.0 10.0 10.0 12.0 13.0 15.0 19.0 21.0

DRILL PIPE FLOAT VALVES

N/A = Not Available. Note: All kits above are for three and four redressing. For single redressing, change last two digits of material number to 10.

MODEL FA - (PLUNGER TYPE VALVE) PRODUCT FAMILY NO. H48012
Size 2F-3R 3F 3 1/2 IF 4R 5F-6R Assembly 480122432 480123400 480123600 480124200 480125462 Wt lb 2.5 5.0 5.0 7.0 16.0 Rubber Repair Kit 016012405 016012505 016012605 016012705 016013005 Wt lb 0.8 1.0 1.0 1.0 1.1 Metal Repair Kit 016011405 016011505 016011505 016011705 016012005 Wt lb 2.0 2.0 2.0 2.0 5.0 Puller Assembly 480912432 480913400 480913400 480914200 480915462 Wt lb 6.0 6.0 6.0 6.0 6.0

MODEL FC AUTOMATIC FILL VALVE (PLUNGER TYPE) PRODUCT FAMILY NO. H48018
Size 2F-3R 3F 3-1/2 IF 4R 4F 5R 5F-6R 6F Assembly 480182432 480183400 480183600 480184200 480184400 480185200 480185462 480186400 Wt lb 2.5 5.0 5.0 7.0 9.5 9.5 16.0 28.0 Rubber Repair Kit 016012400 016012500 016012600 016012700 016012800 016012900 016013000 016013100 Wt lb 0.8 1.0 1.0 1.0 1.0 1.0 1.1 2.0 Metal Repair Kit 070017100 070017300 070017300 070017400 070017500 070017600 070017700 070017800 Wt lb 2.0 2.0 2.0 2.0 3.0 4.0 5.0 5.0 Puller Assembly 480912432 480913400 480913400 480914200 480914400 480915200 480915462 480916400 Wt lb 8.0 10.0 10.0 12.0 13.0 15.0 19.0 21.0

Note: All kits above are for three and four redressing. For single redressing, change last two digits of material number to 10.

MODEL FI - (PLUNGER TYPE VALVE) WITH INTEGRAL BAFFLE PLATE, PRODUCT FAMILY NO. H48014
Size 4R 5F-6R Assembly 480144200 480145462 Wt lb 9.0 18.0 Rubber Repair Kit 016012700 016013000 Wt lb 1.0 1.1 Metal Repair Kit 016011700 016012000 Wt lb 2.0 5.0 Puller Assembly 480914200 480915462 Wt lb 6.0 6.0

53

Baker SPD

ORDERING INFORMATION

ORDERING INFORMATION (MATERIAL NUMBERS AND WEIGHTS)
Standard Service Drill Pipe Float Valves, Repair Kits, and Puller Assemblies MODEL G FULL OPEN VALVE (FLAPPER TYPE) PRODUCT FAMILY NO. H48015
Size 1F-2R 2F-3R 3F 3-1/2 IF 4R 4F 5R 5F-6R Assembly 480151422 480152432 480153400 480153600 480154200 480154400 480155200 480155462 Wt lb 2.0 3.5 5.0 5.0 7.0 8.0 9.0 12.0 Rubber Repair Kit 051988300 016013800 016013900 051982000 016014000 016014100 016014200 016014300 Wt lb 0.5 0.6 1.0 1.0 1.5 1.6 1.6 2.0 Metal Repair Kit 051988400 016013200 016013300 052070200 016013400 016013500 016013600 016013700 Wt lb 0.7 0.8 1.0 1.0 1.1 1.4 1.6 1.8 Puller Assembly 480901422 480902432 480903400 480903400 480904200 480904400 480905200 480905462 Wt lb 7.0 8.0 10.0 10.0 12.0 13.0 15.0 19.0

Note: All kits above are for three and four redressing. For single redressing, change last two digits of material number to 10.

MODEL GA DIFFERENTIAL PRESSURE MONITORING VALVE (PORTED FLAPPER TYPE) PRODUCT FAMILY NO. H48016
Size 1F-2R 2F-3R 3F 3-1/2 IF 4R 4F 5R 5F-6R Assembly 480161422 480162432 480163400 480163600 480164200 480164400 480165200 480165462 Wt lb 2.0 3.5 5.0 5.0 7.0 8.0 9.0 12.0 Rubber Repair Kit 051988300 016013800 016013900 051982000 016014000 016014100 016014200 016014300 Wt lb 0.5 0.6 1.0 1.0 1.5 1.6 1.6 2.0 Metal Repair Kit 052070800 017135000 017136700 052075500 017116000 017136800 017136900 017134200 Wt lb 0.7 0.8 1.0 1.0 1.1 1.4 1.6 1.8 Puller Assembly 480901422 480902432 480903400 480903400 480904200 480904400 480905200 480905462 Wt lb 7.0 8.0 10.0 10.0 12.0 13.0 15.0 19.0

Note: All kits above are for three and four redressing. For single redressing, change last two digits of material number to 10.

MODEL GC AUTOMATIC FILL VALVE (FLAPPER TYPE) PRODUCT FAMILY NO. H48019
Size 2F-3R 3F 3-1/2 IF 4R 4F 5R 5F-6R Assembly 480192432 480193400 480193600 480194200 480194400 480195200 480195462 Wt lb 3.5 5.0 5.0 7.0 8.0 9.0 12.0 Rubber Repair Kit 016013800 016013900 051982000 016014000 016014100 016014200 016014300 Wt lb 0.6 1.0 1.0 1.5 1.6 1.6 2.0 Metal Repair Kit 016013200 016013300 052070200 016013400 016013500 016013600 016013700 Wt lb 0.8 1.0 1.0 1.1 1.4 1.6 1.8 Puller Assembly 480902432 480903400 480903400 480904200 480904400 480905200 480905462 Wt lb 8.0 10.0 10.0 12.0 13.0 15.0 19.0

Note: All kits above are for three and four redressing. For single redressing, change last two digits of material number to 10.

54

ORDERING INFORMATION ORDERING INFORMATION (MATERIAL NUMBERS AND WEIGHTS)
Standard Service Drill Pipe Float Valves, Repair Kits, and Puller Assemblies MODEL GCA - AUTOMATIC FILL WITH DIFFERENTIAL PRESSURE MONITORING VALVE (PORTED FLAPPER TYPE) PRODUCT FAMILY NO. H48019
Incorporates the Benefits of the Automatic Fill Feature into Model GA.
Size 2F-3R 3F 3-1/2 IF 4R 4F 5R 5F-6R Assembly 480192433 480193401 480193601 480194201 480194401 480195201 480195463 Wt lb 3.5 5.0 5.0 7.0 8.0 9.0 12.0 Rubber Repair Kit 016013800 016013900 051982000 016014000 016014100 016014200 016014300 Wt lb 0.6 1.0 1.0 1.5 1.6 1.6 2.0 Metal Repair Kit 017135000 017136700 052075500 017116000 017136800 017136900 017134200 Wt lb .8 1.0 1.0 1.1 1.4 1.6 1.8

Baker SPD

DRILL PIPE FLOAT VALVES

Puller Assembly 480902432 480903400 480903400 480904200 480904400 480905200 480905462

Wt lb 8.0 10.0 10.0 12.0 13.0 15.0 19.0

Note: All kits above are for three and four redressing. For single redressing, change last two digits of material number to 10.

MODEL GB AIR DRILLING VALVE (FLAPPER TYPE) PRODUCT FAMILY NO. H48017
Size 1F-2R 2F-3R 3F 3-1/2 IF 4R 4F 5R 5F-6R Assembly 480171422 480172432 480173400 480173600 480174200 480174400 480175200 480175462 Wt lb 2.0 3.5 5.0 5.0 7.0 8.0 9.0 12.0 Rubber Repair Kit 051988300 016013800 016013900 051982000 016014000 016014100 016014200 016014300 Wt lb 0.5 0.6 1.0 1.0 1.5 1.6 1.6 2.0 Metal Repair Kit O/A 022216100 022216200 022216200 022216300 022216400 022216500 022216600 Wt lb O/A 0.8 1.0 1.0 1.1 1.4 1.6 1.8 Puller Assembly 480901422 480902432 480903400 480903400 480904200 480904400 480905200 480905462 Wt lb 7.0 8.0 10.0 10.0 12.0 13.0 15.0 19.0

O/A = On Application. Note: All kits above are for three and four redressing. For single redressing, change last two digits of material number to 10.

MODEL GBA AIR DRILLING WITH DIFFERENTIAL PRESSURE MONITORING VALVE (PORTED FLAPPER TYPE) PRODUCT FAMILY NO. H48017
Incorporates the Benefits of Differential Pressure Monitoring Feature into the Model GB.
Size 2F-3R 3F 3-1/2 IF 4R 4F 5R 5F-6R Assembly 480172433 480173401 480173601 480174201 480174401 480175201 480175463 Wt lb 3.5 5.0 5.0 7.0 8.0 9.0 12.0 Rubber Repair Kit 016013800 016013900 051982000 016014000 016014100 016014200 016014300 Wt lb 0.6 1.0 1.0 1.5 1.6 1.6 2.0 Metal Repair Kit 017135000 017136700 052075500 017116000 017136800 017136900 017134200 Wt lb 0.8 1.0 1.0 1.1 1.4 1.6 1.8 Puller Assembly 480902432 480903400 480903400 480904200 480904400 480905200 480905462 Wt lb 8.0 10.0 10.0 12.0 13.0 15.0 19.0

Note: All kits above are for three and four redressing. For single redressing, change last two digits of material number to 10.

55

Baker SPD

ORDERING INFORMATION FOR H2S SERVICE

ORDERING INFORMATION (MATERIAL NUMBERS AND WEIGHTS)
H2S Service Drill Pipe Float Valves, Repair Kits, and Puller Assemblies MODEL F - (PLUNGER TYPE) PRODUCT FAMILY NO. H48030
Size 1R 1F-2R 2F-3R 3F 3-1/2 IF 4R 4F 5R 5F-6R 6F Assembly 480301200 480301422 480302432 480303400 480303600 480304200 480304400 480305200 480305462 480306400 Wt lb 1.5 1.5 2.5 5.0 5.0 7.0 9.5 9.5 16.0 28.0 Rubber Repair Kit 071081701 071081801 071081901 071082001 071082101 071082201 071082301 071082401 071082501 071082601 Wt lb .5 .7 .8 1.0 1.0 1.0 1.0 1.0 1.1 2.0 Metal Repair Kit 071084901 071085001 071085101 071085201 071085301 071085401 071085501 071085601 071085701 071085801 Wt lb 1.0 2.0 2.0 2.0 2.0 2.0 3.0 4.0 5.0 5.0 Puller Assembly 480911200 480911200 480912432 480913400 480913400 480914200 480914400 480915200 480915462 480916400 Wt lb 6.0 7.0 8.0 10.0 10.0 12.0 13.0 15.0 19.0 21.0

Note: All kits above are for three and four redressing. For single redressing change last two digits of material number to 10

H2S Service Repair Kits and Puller Assemblies MODEL FA - (PLUNGER TYPE VALVE) FOR H2S SERVICE PRODUCT FAMILY NO. H48035
Size 2F-3R 3F 3 1/2 IF 4R 5F-6R Assembly Part No. 480352432 480353400 480353600 480354200 480355462 Wt lb 2.5 5.0 5.0 7.0 16.0 Rubber Repair Kit 071081905 071082005 071082105 071082205 071082505 Wt lb 0.8 1.0 1.0 1.0 1.1 Metal Repair Kit 071085105 071085205 071085305 071085405 071085705 Wt lb 2.0 2.0 2.0 2.0 5.0 Puller Assembly 480912432 480913400 480913400 480914200 480915462 Wt lb 6.0 6.0 6.0 6.0 6.0

MODEL G - (FLAPPER TYPE) PRODUCT FAMILY NO. H48031
Size 1F-2R 2F-3R 3F 3-1/2 IF 4R 4F 5R 5F-6R Assembly 480311422 480312432 480313400 480313600 480314200 480314400 480315200 480315462 Wt lb 2.0 3.5 5.0 5.0 7.0 8.0 9.0 12.0 Rubber Repair Kit 051997200 071082701 071082801 052125001 071082901 071083001 071083101 071083201 Wt lb .5 .6 1.0 1.0 1.5 1.6 1.6 2.0 Metal Repair Kit 051997300 071085901 071086001 052125101 071086101 071086201 071086301 071086401 Wt lb .7 .8 1.0 2.0 1.1 1.4 1.6 1.8 Puller Assembly 480901422 480902432 480903400 480903400 480904200 480904400 480905200 480905462 Wt lb 7.0 8.0 10.0 10.0 12.0 13.0 15.0 19.0

Note: All kits above are for three and four redressing. For single redressing change last two digits of material number to 10

56

ORDERING INFORMATION FOR H2S SERVICE ORDERING INFORMATION (MATERIAL NUMBERS AND WEIGHTS)
H2S Service Repair Kits and Puller Assemblies (Continued) MODEL GC - AUTOMATIC FILL (FLAPPER TYPE) PRODUCT FAMILY NO. H48033
Size 2F-3R 3F 4R 4F 5R 5F-6R Assembly 480332432 480333400 480334200 480334400 480335200 480335462 Wt lb 3.5 5.0 7.0 8.0 9.0 12.0 Rubber Repair Kit 071082701 071082801 071082901 071083001 071083101 071083201 Wt lb 0.6 1.0 1.5 1.6 1.6 2.0 Metal Repair Kit 071085901 071086001 071086101 071086201 071086301 071086401 Wt lb 0.8 1.0 1.1 1.4 1.6 1.8

Baker SPD

Puller Assembly 480902432 480903400 480904200 480904400 480905200 480905462

Wt lb 8.0 10.0 12.0 13.0 15.0 19.0

DRILL PIPE FLOAT VALVES

Note: All kits above are for three and four redressing. For single redressing change last two digits of material number to 10

MODEL GA - AUTOMATIC FILL WITH DIFFERENTIAL PRESSURE MONITORING (PORTED FLAPPER TYPE) PRODUCT FAMILY NO. H48026
Size 1F2R 2F3R 3F 4R 4F 5R 5F6R Assembly 480261422 480262432 480263400 480264200 480264400 480265200 480265462 Wt lb 2.0 3.5 5.0 7.0 8.0 9.0 12.0 Rubber Repair Kit O/A O/A O/A O/A O/A O/A O/A Wt lb Metal Repair Kit O/A O/A O/A O/A O/A O/A O/A Wt lb Puller Assembly 480901422 480902432 480903400 480903400 480904200 480905200 480905462 Wt lb 7.0 8.0 10.0 10.0 12.0 15.0 19.0

O/A = On Application. Note: All kits above are for three and four redressing. For single redressing, change last two digits of material number to 10.

MODEL GB - AIR DRILLING (FLAPPER TYPE) PRODUCT FAMILY NO. H48034
Size 2F3R 4R Assembly 480342432 480344200 Wt lb 3.5 7.0 Rubber Repair Kit O/A O/A Wt lb Metal Repair Kit 051998400 051999500 Wt lb 0.8 1.1 Puller Assembly 480902432 480904200 Wt lb 8.0 12.0

O/A = On Application. Note: All kits above are for three and four redressing. For single redressing, change last two digits of material number to 10.

57

Baker SPD

ORDERING INFORMATION FOR STEAM SERVICE

ORDERING INFORMATION (MATERIAL NUMBERS AND WEIGHTS)
Steam Service MODEL F - (PLUNGER TYPE), PRODUCT FAMILY NO. H48020
Size 1R 1F-2R 2F-3R 3F 3-1/2 IF 4R 4F 5R 5F-6R 6F Assembly 480201200 480201422 480202432 480203400 480203600 480204200 480204400 480205200 480205462 480206400 Wt lb 1.5 1.5 2.5 5.0 5.0 7.0 9.5 9.5 16.0 28.0 Rubber Repair Kit 070502400 070502500 070502600 070502700 070502800 070502900 070503000 070503100 070503200 070503300 Wt lb 0.5 0.7 0.8 1.0 1.0 1.0 1.0 1.0 1.1 2.0 Metal Repair Kit 015929800 016011300 016011400 016011500 016011500 016011700 016011800 016011900 016012000 016012100 Wt lb 1.0 2.0 2.0 2.0 2.0 2.0 3.0 4.0 5.0 5.0 Puller Assembly 480911200 480911200 480912432 480913400 480913400 480914200 480914400 480915200 480915462 480916400 Wt lb 6.0 7.0 8.0 10.0 10.0 12.0 13.0 15.0 19.0 21.0

Note: All kits above are for three and four redressing. For single redressing, change last two digits of material number to 10

MODEL G - (FLAPPER TYPE), PRODUCT FAMILY NO. H48021
Size 1F-2R 2F-3R 3F 3-1/2 IF 4R 4F 5R 5F-6R Assembly 480211422 480212432 480213400 480213600 480214200 480214400 480215200 480215462 Wt lb 2.0 3.5 5.0 5.0 7.0 8.0 9.0 12.0 Rubber Repair Kit O/A 070305600 070305700 052075600 070305800 070305900 070306000 070306100 Wt lb 0.6 1.0 1.0 1.5 1.6 1.6 2.0 Metal Repair Kit O/A 016013200 016013300 O/A 016013400 016013500 016013600 016013700 Wt lb 0.8 1.0 2.0 1.1 1.4 1.6 1.8 Puller Assembly 480901200 480902432 480903400 480903600 480904200 480904400 480905200 480905462 Wt lb 7.0 8.0 10.0 10.0 12.0 13.0 15.0 19.0

O/A = On Application. Note: All kits above are for three and four redressing. For single redressing, change last two digits of material number to 10

MODEL GB - AIR DRILLING (FLAPPER TYPE), PRODUCT FAMILY NO. H48023
Size 5R Assembly 480235200 Wt lb 9.0 Rubber Repair Kit 070306000 Wt lb 1.6 Metal Repair Kit 022216500 Wt lb 1.6 Puller Assembly 480905200 Wt lb 15.0

Note: All kits above are for three and four redressing. For single redressing, change last two digits of material number to 10.

MODEL GC - AUTOMATIC FILL (FLAPPER TYPE), PRODUCT FAMILY NO. H48024
Size 4R Assembly 480244200 Wt lb 7.0 Rubber Repair Kit O/A Wt lb Metal Repair Kit O/A Wt lb Puller Assembly 480904200 Wt lb 12.0

O/A = On Application. Note: All kits above are for three and four redressing. For single redressing, change last two digits of material number to 10

MODEL GCA - AUTOMATIC FILL WITH DIFFERENTIAL PRESSURE MONITORING (PORTED FLAPPER TYPE) PRODUCT FAMILY NO. H48025
Incorporates the Benefits of the Automatic Fill Feature into Model GA.
Size 4R 5F6R Assembly 480254200 480255462 Wt lb 7.0 12.0 Rubber Repair Kit O/A O/A Wt lb Metal Repair Kit O/A O/A Wt lb Puller Assembly 480904200 480905462 Wt lb 12.0 19.0

O/A = On Application. Note: All kits above are for three and four redressing. For single redressing, change last two digits of material number to 10

58

WV T 7 9 1 7 2 2 WV T 7 9 1 7 2 6 WV T 7 9 1 7 2 3 WV T 7 9 1 7 2 4 WV T 7 9 1 7 2 5 WV T 7 9 1 7 4 0 WV T 7 9 1 7 4 1 WV T 7 9 1 7 4 2 WV T 7 9 1 7 4 3 WV T 7 9 1 7 4 4

0 . 7 5 9 / 1 6 ” A P I R e g u l a r 5 9 / 1 6 ” A P I F u l l H o l e 6 5 / 8 ” A P I R e g u l a r 6 5 / 8 ” A P I F u l l H o l e 3 1 / 2 ” A P I I n t e r n a l F l u s h 2 7 / 8 ” A P I I n t e r n a l F l u s h 3 1 / 2 ” A P I I n t e r n a l F l u s h 4 1 / 2 ” A P I I n t e r n a l F l u s h 2 7 / 8 ” A P I I n t e r n a l F l u s h 4 ” A P I I n t e r n a l F l u s h 5 R 5 F 6 R 5 F 6 R 6 F 3 1 / 2I F 2 F 3 R 3 1 / 2I F 5 R 2 F 3 R 4 F S p i d e r 0 . 7 1 . 0 0 . 6 R i n g S p i d e r R i n g 0 . 7 1 . 3 0 . 7 1 . 0

Baker SPD Drill Pipe Float Valve

Repair Manual
Table of Contents
Contents Page

Scope.....................................................................................1 Reference...............................................................................1 Disassembly...........................................................................2 Model F.........................................................................2 Model G........................................................................4 Inspection...............................................................................7 Preparation....................................................................7 Model F.........................................................................7 Visual...................................................................7 Dimensional.........................................................7 Model G........................................................................7 Visual...................................................................7 Dimensional.........................................................8 Reassembly & Inspection......................................................9 Model F.........................................................................9 Model G......................................................................12 Packaging...............................................................................16 Appendix................................................................................17 Model F (Dimensional Data)........................................18 Model G (Dimensional Data).......................................19
Printed as an uncontrolled document

Baker SPD Repair Manual Drill Pipe Float Valve

Scope
The Baker SPD Repair Manual outlines the disassembly, inspection, reassembles, painting and packaging for the Model F and Model G Series Drill Pipe Float Valves (DPFV).

Reference
The Baker SPD Catalog provides all commodity (part) number information for ordering spare parts. Any questions regarding the Repair Manual or Catalog should be addressed to Baker SPD Customer Service Department.

Printed as an uncontrolled document

1

Baker SPD Repair Manual Drill Pipe Float Valve Disassembly Model F Series:
Tools Required: 1-Flat Head Screwdriver 1-Vise (Optional) Disassembly Procedure: Side Seals: Secure the cage with a vise or by hand as shown in the figures. Insert a flat head screwdriver in between the seal groove and side seal. (Fig. 1) Pry the side seal up until the tip of screwdriver can be pushed out to the edge of the DPFV. (Fig. 2) Next, pry the side seal off of the DPFV. (Fig. 3)

Figure 1

Figure 2

Figure 3

Printed as an uncontrolled document

2

Baker SPD Repair Manual Drill Pipe Float Valve
Insert a flat head screwdriver in between the seal groove and side seal. (Fig. 4) Pry the side seal up until the tip of screwdriver can be pushed out to the edge of the DPFV. Next, using a twisting motion pry the side seal off of the DPFV. (Fig. 5)

Figure 4

Figure 5

Valve and Components: Stand cage with grooves for side seals in the downward position. Depress the valve guide until the guide is no longer held in by the cage. (Note: Always maintain pressure on the guide.) (Fig. 6) Rotate the valve stem out through the cage slot until the guide and spring can

Figure 6

Figure 7

be removed. (Fig. 7) Slowly remove pressure on the guide until spring is no longer compressed. Remove guide, spring and valve from cage. Remove valve seal and disc from valve. Caution: Compressed spring can be dangerous.

Printed as an uncontrolled document

3

Baker SPD Repair Manual Drill Pipe Float Valve Model G Series:
Tools Required: 1-Flat Head Screwdriver 1-Puller Tool 1-Pliers 1-Vise (Optional) Disassembly Procedure: Side Seals: Secure the cage with a vise or by hand as shown in the figures. Insert a flat head screwdriver in between the seal groove and side seal. (Fig. 8) Pry the side seal up until the tip of screwdriver can be pushed out to the edge of the DPFV. (Fig. 9) Next, pry the side seal off of the DPFV. (Fig. 10)

Figure 8

Figure 9

Figure 10

Insert a flat head screwdriver in between the seal groove and side seal. (Fig. 11) Pry the side seal up until the tip of screwdriver can be pushed out to the edge of the DPFV. Next, using a twisting motion pry the side seal off of the DPFV. (Fig. 12)

Printed as an uncontrolled document

4

Baker SPD Repair Manual Drill Pipe Float Valve

Figure 11

Figure 12

Flapper Components: Remove flapper retaining pin with a pair of pliers. (Fig. 13 & 14) Remove spring and flapper.

Figure 13

Figure 14

Seal and Retaining Ring: Stand cage with grooves for side seals in the upward position. Insert the puller tool through the middle of the DPFV until tool seats against the ring. (Fig. 15) Holding puller centered, slide “hammer” up and forcefully slide downward. (Fig. 16) Repeat until retaining ring dislodges. (Fig. 17)

Printed as an uncontrolled document

5

Baker SPD Repair Manual Drill Pipe Float Valve

Figure 15

Figure 16

Figure 17

Shock Absorber: Stand cage with shock absorber in the upward position. Insert flat head screwdriver in between top of the cage and shock absorber. (Fig. 18) Pry shock absorber upward until it becomes dislodged from the DPFV cage. (Fig. 19)

Figure 18

Figure 19

Printed as an uncontrolled document

6

Baker SPD Repair Manual Drill Pipe Float Valve Inspection Preparation:
All metal components shall be shot or sand blast for a appropriate amount of time to remove all corrosion build up. All rubber material and Model G springs shall be discarded.

Model F Series:
Visual Inspection: Visually check each component for excessive wear. Acceptance of visual examination is as follows: 1) Cage shall not be washed out on any of the sealing areas. 2) Valve shall not be washed out. 3) Valve stem shall not be loosely attached to valve head. Any movement of the stem relative to the valve head shall be grounds for rejection and subsequent replacement of valve. Dimensional Inspection: Dimensions shown in the appendix on page 18 shall be considered acceptable criteria for inspection. Any deviations from the dimensions shown shall be cause for replacement.

Model G Series:
Visual Inspection: Visually check each component for excessive wear. Acceptance of visual examination is as follows:

Printed as an uncontrolled document

7

Baker SPD Repair Manual Drill Pipe Float Valve
1) Cage shall not be washed out on any of the sealing areas or hinge pin area. 2) Flapper shall not be washed out or have evidence of pitting on sealing surfaces. Dimensional Inspection: Dimensions shown in the appendix on page 19 shall be considered acceptable criteria for inspection. Any deviations from the dimensions shown shall be cause for replacement.

Printed as an uncontrolled document

8

Baker SPD Repair Manual Drill Pipe Float Valve Reassembly Model F Series:
Tools Required: 1-Flat Head Screwdriver 1-Hammer 1-Vise (Optional) Hydraulic Oil Assembly Procedure: Side Seals: Stand cage with grooves for side seals in the upward position. Place a small amount of oil on the inside diameter of both side seals. (Fig.

Figure 20

Figure 21

20) Place one edge of seal (flat side up) into the top seal groove and hold with thumb. (Fig. 21) Insert screwdriver horizontally between groove and seal on either side of the cage. (Fig. 22) Rotate

Figure 22 Printed as an uncontrolled document

Figure 23 9

Baker SPD Repair Manual Drill Pipe Float Valve
screwdriver around cage until the seal seats in top groove. (Do not remove screwdriver) Manipulate screwdriver until one edge of screwdriver is seated in the lower seal groove. (Fig. 23) Rotate screwdriver until seal seats into lower groove. Place one edge of seal (flat side down) into the top seal groove. (Fig. 24) Insert screwdriver horizontally between groove and seal on either side of the cage. (Fig. 25) Rotate screwdriver around cage until the seal seats in top groove.

Figure 24

Figure 25

Valve Components: Place valve seal on valve sub-assembly. (Flat side facing valve) (Fig. 26) Place valve disk on valve. (Flat side facing valve) (Fig. 27) Hold valve cone side down and place spring on valve sub-assembly.

Figure 26

Figure 27

Printed as an uncontrolled document

10

Baker SPD Repair Manual Drill Pipe Float Valve
(Fig. 28) Place guide bevel side down on top of spring. (Fig. 29) Holding sub-assembly together, place valve sub-assembly into slot side of cage. Depress the guide until the stem can be rotated into the slot. (Do not release guide)

Figure 28

Figure 29

(Fig.30) Rotate valve sub-assembly into cage until stem is through the slot. (Fig. 31) Release guide and insure that guide shoulder seats on cage.

Figure 30

Figure 31

Figure 32

Inspection: (Fig. 32) Review assembly to assure valve moves freely in cage and properly seals. Assure valve retaining mechanism properly fits and functions on all model ‘FC’ DPFV.

Printed as an uncontrolled document

11

Baker SPD Repair Manual Drill Pipe Float Valve Model G Series:
Tools Required: 1-Flat Head Screwdriver 1-Puller Tool 1-Hammer 1-Vise (Optional) Hydraulic Oil Assembly Procedure: Side Seals: Stand cage with grooves for side seals in the upward position. Place a small amount of oil on the inside diameter of both side seals. (Fig.

Figure 33

Figure 34

33) Place one edge of seal (flat side up) into the top seal groove and hold with thumb. (Fig. 34) Insert screwdriver horizontally between groove and seal on either side of the cage. (Fig. 35) Rotate

Figure 35

Figure 36

Printed as an uncontrolled document

12

Baker SPD Repair Manual Drill Pipe Float Valve
screwdriver around cage until the seal seats in top groove. (Do not remove screwdriver) Manipulate screwdriver until one edge of screwdriver is seated in the lower seal groove. (Fig. 36) Rotate screwdriver until seal seats into lower groove. Place one edge of seal (flat side down) into the top seal groove. (Fig. 37) Insert screwdriver horizontally between groove and seal on either side of the cage. (Fig. 38) Rotate screwdriver around cage until the seal seats in top groove.

Figure 37

Figure 38

Seal and Retaining Ring: Stand cage with grooves for side seals in the downward position. Prior to installing groove, visually inspect groove to assure that no debris is present. If there is debris present, thoroughly clean groove. Place seal into seal groove. (Fig. 39) Place retaining ring into ID of seal. (Fig. 40) Insert the puller tool through the middle of the DPFV until tool seats into ring. (Fig. 41)

Figure 39

Figure 40

Figure 41

Printed as an uncontrolled document

13

Baker SPD Repair Manual Drill Pipe Float Valve
Holding the puller tool in the center of the cage, slide “hammer” up and forcefully slide downward. (Fig. 42) Repeat until retaining ring seats on the cage. (A metal to metal sound will be heard when ring seats on cage.) Proper seating of the flapper seal and retaining ring are shown in Fig. 43.

Figure 43 Figure 42

Flapper Components: Place flapper into cage and align pin holes. (Fig. 44) Place spring into position and hold with thumb. (Fig. 45) Insert pin into position. (Fig. 46) Note: Model ‘GB’ DPFV’s do not have spring.

Figure 44

Figure 45

Printed as an uncontrolled document

14

Baker SPD Repair Manual Drill Pipe Float Valve
Shock Absorber: Stand cage with side seals in the downward position. Place shock absorber onto cage. Insert flat head screwdriver in between top of the cage and shock absorber. (Fig. 47) Twist shock absorber around until it seats on the DPFV cage.

Figure 46

Figure 47

Inspection: Review assembly to assure flapper moves freely and seals properly. Assure flapper retention mechanism properly fits and functions on model ‘GC’ DPFV.

Printed as an uncontrolled document

15

Baker SPD Repair Manual Drill Pipe Float Valve Paint and Packaging:
Prior to assembly all metal components except springs will be painted “Baker Blue”. Package all DPFV’s in the appropriate white box with appropriate labeling. Contact Baker SPD manufacturing department for detailed information regarding painting and packaging.

Printed as an uncontrolled document

16

Baker SPD Repair Manual Drill Pipe Float Valve

Appendix

Printed as an uncontrolled document

17

Baker SPD Repair Manual Drill Pipe Float Valve
Model F Series
A B C D E F G H J Size Minimum Minimum Minimum Maximum Maximum Maximum Maximum Minimum Minimum 1.641 1.484 1.234 1.156 1.344 0.577 0.370 0.148 5.813 1R 1.891 1.703 1.484 1.453 1.688 0.577 0.343 0.102 6.188 1F-2R 2.391 2.172 2.016 1.766 2.063 0.765 0.312 0.180 6.438 2F-3R 2.797 2.531 2.203 2.109 2.391 0.827 0.406 0.203 9.906 3F 3.100 2.870 2.530 2.110 2.660 0.840 0.406 0.220 9.906 3.5IF (BS) 3.641 3.375 3.047 2.766 3.078 1.140 0.391 0.563 11.906 4F 3.453 3.172 2.891 2.578 2.969 1.015 0.344 0.242 8.250 4R 3.859 3.547 3.203 3.047 3.266 1.265 0.343 0.297 9.656 5R 4.766 4.484 4.781 3.672 4.031 1.265 0.540 0.367 11.656 5F-6R 5.672 5.391 4.953 4.609 4.969 1.265 0.540 0.351 14.531 6F

Printed as an uncontrolled document

18

Baker SPD Repair Manual Drill Pipe Float Valve
Model G Series
Size 1F-2R 2F-3R 3F 3.5IF 4R 4F 5R 5F-6R A B C D E F G H Minimum Minimum Minimum Maximum Maximum Minimum Maximum Minimum 1.890 1.710 1.490 1.187 0.350 0.240 0.131 5.937 2.391 2.172 2.016 1.436 0.312 0.305 0.194 6.156 2.797 2.531 2.203 1.811 0.406 0.320 0.194 9.578 3.109 2.844 2.470 1.811 0.406 0.484 0.194 9.578 3.453 3.172 2.891 2.249 0.343 0.414 0.255 11.563 3.641 3.375 3.047 2.467 0.406 0.407 0.255 7.891 3.859 3.547 3.203 2.562 0.343 0.445 0.255 9.219 4.766 4.484 4.078 3.186 0.540 0.531 0.350 11.218

Printed as an uncontrolled document

19

Sponsor Documents

Or use your account on DocShare.tips

Hide

Forgot your password?

Or register your new account on DocShare.tips

Hide

Lost your password? Please enter your email address. You will receive a link to create a new password.

Back to log-in

Close