Power Electronics

Published on January 2017 | Categories: Documents | Downloads: 42 | Comments: 0 | Views: 666
of 10
Download PDF   Embed   Report

Comments

Content

CURRICULUM 2009 – 10, With Effect From 2010 – 11 Department of Technical Education DIPLOMA COURSE IN ELECTRICAL AND ELECTRONICS ENGINEERING Fourth Semester Sub: POWER ELECTRONICS Sub Code: Contact Hrs/Week: 4 Chapter No. Topic UNIT I 1 2 3 4 5 6 7 8 9 10 11 12 Power semiconductor devices SCR controlled circuits UNIT II Controlled rectifiers Choppers Inverters Cycloconverters Device Protection UNIT III Power Supplies and Stabilizers Switch Mode Converters Power Electronics Applications Industrial innovations Tests and Revision TOTAL 8 5 4 6 4 __________ 64 5 2 4 2 6 12 6 Contact Hrs/Sem: 64 No. of Hours.

EE – Fourth Semester – Power Electronics

Page 1 of 10

CURRICULUM 2009 – 10, With Effect From 2010 – 11 CONTENT 1 Power Semiconductor Devices Power Diode, SCR, TRIAC, DIAC, BJT, MOSFET, IGBT 2 SCR control circuits a) Turn-on methods b) Turn-off methods (Commutation) 3 Controlled Rectifiers (AC to DC Line commutated converters) Principle of phase control Single phase fully controlled bridge rectifier Three phase fully controlled bridge rectifier 4 5 6 7 Chopper Step-down, Step-up choppers Inverter Single phase half bridge, full bridge and three phase full bridge Cycloconverters Device Protection Rating, Specification and Nomenclature of SCRs Protection of SCRs Selection of SCRs 8 Reliability and failure mechanism of SCRs Power Supplies Stabilizers DC regulated supplies using IC (Linear Power Supplies) Switched Mode Power Supplies(SMPS)

9

Power supplies for Battery charger Switch Mode Converters Flyback DC to DC converter. Forward or buck or step down DC to DC converter. Boost or step up DC to DC converter. Buck- boost DC to DC converter. 10 Power Electronics Applications. Speed control of separately excited DC motor by armature voltage control method. Speed control of Induction Motor by Variable voltage -frequency method. Optocoupler device construction. Solid state relay SSR. 11 Industrial innovations

EE – Fourth Semester – Power Electronics

Page 2 of 10

CURRICULUM 2009 – 10, With Effect From 2010 – 11 12 Tests and Revision REFERENCES:
1. Power Electronics by Mohan, Undeland & Robbins –Wiley India.

2. Power Electronics By Umanand - Wiley India GENERAL EDUCATIONAL OBJECTIVES: 1 2 3 4 5 6 7 8 Know the principle of operation, characteristics and applications of power Semiconductor devices Understand turn-on and turn-off methods for SCR. Know the operation of controlled rectifier Know the operation of chopper Know the operation of inverter Know the operation of cycloconverter. Understand ratings, specifications, protection, selection and reliability of SCR. Know the operation of power supplies, stabilizers. SPECIFIC INSTRUCTIONAL OBJECTIVES 1 Power Semiconductor devices 1.1 Power Diode 1.1.1 Explain V-I characteristic curve of power diode 1.1.2 List applications of power diode 1.2 SCR 1.2.1 Draw the layer diagram of SCR and explain the same 1.2.2 Explain the two transistor analogy of SCR(no derivation) 1.2.3 Explain the static V-I characteristic curve of SCR 1.2.4 List applications of SCR 1.3 TRIAC 1.3.1 Explain the operation of triac and draw its static V-I characteristic curve 1.3.2 List the modes of operation of triac and mention the preferred modes 1.3.3 List applications of triac 1.4 DIAC 1.4.1 Explain the operation of diac and draw its V-I characteristic curve 1.4.2 List applications of diac 1.5 BJT 12hrs

EE – Fourth Semester – Power Electronics

Page 3 of 10

CURRICULUM 2009 – 10, With Effect From 2010 – 11 1.5.1 Describe the operation of an NPN transistor as a switch 1.5.2 List the applications of BJT in power switching applications 1.6 MOSFET 1.6.1 Explain the operation of MOSFET and draw its transfer characteristic curve 1.6.2 List applications of MOSFET 1.7 IGBT 1.7.1 Explain the operation of IGBT and draw its V-I characteristics 1.7.2 List applications of IGBT 1.7.3 Compare IGBT,BJT and MOSFET Reference book: Industrial Electronics and controls-Biswanath paul Reference Books: 1 M Ramamoorthy 2 Clay Laster 3 Mohan and Rashid 2 SCR control circuits 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.7 2.8 Describe briefly different methods of Turn-ON SCR List two general functions to be fulfilled by gate control circuits Draw the general layout diagram of firing circuit and explain. Draw R firing circuit and explain . Draw R-C firing circuit and explain. Draw UJT pulse trigger circuit and explain. Explain Digital firing circuit. Define commutation List different types of commutation

Page.No:298

6hrs

Ref: for 1.2 complete GK Dubey 3 Controlled Rectifiers 3.1 3.2 3.3 3.4 3.5 3.6 5hrs

Explain controlled rectifiers Explain single quadrant semi converter, two quadrant full converter and dual converter Explain line or natural commutation Explain the principle of phase control and define firing angle (alpha) and conduction angle (beeta) Explain with schematic diagram and waveforms, the operation of single phase half wave controlled converter. Explain with schematic diagram and waveforms, the operation of single phase fully controlled bridge converter

EE – Fourth Semester – Power Electronics

Page 4 of 10

CURRICULUM 2009 – 10, With Effect From 2010 – 11 3.7 Explain with circuit diagram and waveforms the operation of fully controlled three phase bridge Converter Ref: Rashid GK Dubey M Ramamoorthy 4 Choppers 4.1 4.2 4.3 2hrs

Define chopper Draw the basic power circuit (without commutation circuit) of a step down chopper and explain its operation with waveforms Draw the basic power circuit (without commutation circuit) of a step up chopper and explain its operation with waveforms

Ref: GK Dubey Dewan 5 Inverters 4hrs 5.1 Define Inverter. 5.2 Classify the inverters based on Source. 5.3 Define Voltage Source Inverter and Current Source Inverter. 5.4 Differentiate between Voltage Source Inverter and Current Source Inverter 5.5 Draw the schematic diagram of voltage source single phase half bridge inverter (without commutation circuit) and explain its operation 5.6 5.7 Draw the schematic diagram of voltage source single phase full bridge inverter (without commutation circuits) and explain its operation Draw the schematic diagram of voltage source three phase bridge inverter (without commutation circuit) and explain its operation

Ref Ramamoorthy Rashid Industrial Electronics and controls-Biswanath paul Page.No:340 and 341(For Sections 5.2,5.3 and 5.4) 6 Cycloconverters 6.1 6.2 6.3 7 2hrs

Define cycloconverter and mention its types (step up and step down) State the advantages and disadvantages of cycloconverter Draw the diagram of a single phase to single phase cycloconverter and explain 6hrs

Ref Rashid Device Protection

EE – Fourth Semester – Power Electronics

Page 5 of 10

CURRICULUM 2009 – 10, With Effect From 2010 – 11 7.1 7.2 7.3 7.4 7.5 7.6 7.7 Give specifications, ratings and nomenclature of Thyristors, BJT, MOSFET and IGBT Describe how SCR can be protected against overvoltage and overcurrent Describe dv/dt and di/dt protection of SCR Describe the process involved in selecting an SCR for a particular application Define reliability of SCR and mean time between failures (MTBF) Explain the three failures of an SCR (Mechanical, Electrical and Thermal) Explain mounting of SCR with suitable heat sink.

Ref: Ramamoorthy Rashid Dubey MD Singh, Clay Laster

8

Power Supplies, Stabilizers 8.1

8hrs

Draw a schematic diagram of switched mode power supply (SMPS) and explain its operation 8.2 Compare linear power supply with SMPS 8.3 List the applications of linear power supply and SMPS 8.4 Draw a schematic diagram of SCR battery charger and explain 8.5 Define online UPS system and offline UPS system 8.6 Draw a block diagram of UPS system and explain its operation 8.7 Determine Battery size and required voltage for UPS(Ref: Modern Power Electronics by P.C.Sen Page No.832 and 833) 8.8 List the areas of applications of UPS system 8.9 Define the different types of power line disturbances such as overvoltage, black out voltage spike, chopped voltage, harmonics, Total Harmonics Distortion factor and EMI 8.10 List the sources of power line disturbances of mentioned in 8.9 8.11 Give the effect of power line disturbances on sensitive equipments such as computer 8.12 Describe how power conditioners provide effective suppressing of some or all of these electrical disturbances 8.13 Describe the operation of relay type AC voltage stabilizer with the help of diagram 8.14 Draw the diagram of constant voltage transformer (CVT) type AC voltage stabilizer and explain its operation 8.15 Draw the diagram of AC servo voltage stabilizer and explain its operation Ref: Gayakwad Mohan Schuler and Mc Namee Bradley

EE – Fourth Semester – Power Electronics

Page 6 of 10

CURRICULUM 2009 – 10, With Effect From 2010 – 11 Harish C Rai Chute & Chute MC Sharma Ramamoorthy Whittington, Universities Press(India) Pvt. Ltd. Switch Mode Converters 9.1 9.2 9.3 9.4 9.5

9

5hrs

Explain with circuit diagram Flyback DC to DC converter. Explain with circuit diagram Forward or buck or step down DC to DC converter. Explain with circuit diagram boost or step up DC to DC converter. Explain with circuit diagram buck- boost DC to DC converter. Compare buck, boost and buck-boost DC to DC converter. Ref: Biswanath Paul PHI Publication Edition-II Page. No: 36 to 44

10

Power Electronics applications 4hrs 10.1 Explain speed control of shunt –wound DC motor by armature voltage control method. 10.2 Explain speed control of Induction Motor by Variable voltage -frequency method. Ref: Biswanath Paul PHI Publication Edition-II Page.No: 403 to 405,408 to 419 10.3 Give basic optocoupler device construction and explain

10.4 Circuit diagram of solid state relay SSR and explain 10.5 State the advantages of SSR over electromechanical relay and give its applications 11 Industrial innovation and seminars (Not for end examination) 6hrs 11.1 seminars by industrial experts/academic experts/visit to nearby industry 12 Tests and revision Total POWER ELECTRONICS TENTATIVE CHAPTER WISE MARK DIVISION 4hrs 64hrs

Hours UNIT I

Approx Total marks for setting questions in the chapter

EE – Fourth Semester – Power Electronics

Page 7 of 10

CURRICULUM 2009 – 10, With Effect From 2010 – 11 1 2 Power semiconductor devices SCR controlled circuits 12 6 30 15

UNIT II 3 4 5 6 7 Controlled rectifiers Choppers Inverters Cycloconverters Device Protection 5 2 4 2 6 15 5 10 5 15

UNIT III 8 9 10 11 12 Power Supplies and Stabilizers Switch Mode Converters Power Electronics Applications Industrial innovations Tests and Revision TOTAL 8 5 4 6 (Ex) 4 (Ex) 54 135 20 10 10

There is a compulsory part of 10 marks in the beginning, out of which, 05 marks is for “Fill in the blanks” type questions.

EE – Fourth Semester – Power Electronics

Page 8 of 10

CURRICULUM 2009 – 10, With Effect From 2010 – 11 MODEL QUESTION PAPER POWER ELECTRONICS TIME: 03 hrs FOURTH SEMESTER ELECTRICAL AND ELECTRONICS Max marks: 100

NOTE: 1. Part A is compulsory 2. Answer TWO FULL questions each from section-II, III, IV Section-I 1. a) Fill in the blanks with appropriate word/words 05 i) Holding current is ………. than Latching current. ii) The current rating of SCR TYN 604 is ………amps. iii) dv/dt protection is given by ………..circuit. iv) MCT 2E is a/an ………….. b) Explain the selection of thyristor for a given application 05 Section-II
2. a) Draw the layer diagram of SCR and explain the same

b) Draw UJT pulse trigger circuit, waveform and explain. c) List any five applications of MOSFET.
3. a) List the modes of operation of triac and mention the preferred modes

01+03 02+02+02 05 02+01 10 02 05+05 02+03

b) Compare IGBT,BJT and MOSFET c) Define forward breakover voltage 4. a) Explain Digital firing circuit b) Describe the operation of an NPN transistor as a switch Section-III
5. a) Explain with circuit diagram and waveforms the operation of fully controlled

three phase bridge Converter 03+03+03 b) State any three advantages and three disadvantages of cycloconverter 03+03 6. a) Draw the basic power circuit of a step down chopper and explain its operation with waveforms 02+02+03 b) Describe how SCR can be protected against overvoltage and over current 04+04 7. a) Draw the schematic diagram of voltage source three phase bridge inverter in 120 degree mode and explain its operation 03+03+04 b) Explain line or natural commutation 02+03

Section-IV

EE – Fourth Semester – Power Electronics

Page 9 of 10

CURRICULUM 2009 – 10, With Effect From 2010 – 11

8. a) Draw a block diagram of Online UPS system and explain its operation 02+03 b) Explain speed control of Induction Motor by Variable voltage- variable frequency method. 05+05 9. a) Define black out, EMI and chopped waveform 02+02+02 b) Give basic optocoupler device construction and explain 02+03 c) List any four application of SSR. 04 10. a) Draw a schematic diagram of switched mode power supply (SMPS) and explain its operation 05+05 b) Draw a Flyback DC to DC converter. 05

EE – Fourth Semester – Power Electronics

Page 10 of 10

Sponsor Documents

Or use your account on DocShare.tips

Hide

Forgot your password?

Or register your new account on DocShare.tips

Hide

Lost your password? Please enter your email address. You will receive a link to create a new password.

Back to log-in

Close