Professional Water Rocket Guide

Published on February 2017 | Categories: Documents | Downloads: 41 | Comments: 0 | Views: 217
of 24
Download PDF   Embed   Report

Comments

Content


http://www.instructables.com/id/Professional-water-rocket-guide/
Home   Sign Up!   Browse   Community   Submit
   All     Art     Craft     Food     Games     Green     Home     Kids     Life     Music     Offbeat     Outdoors     Pets     Photo     Ride     Science     Tech
Professional water rocket guide
by oscarthompson on June 17, 2009
Table of Contents
Author:   oscarthompson . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
License:   Attribution Non-commercial (by-nc) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Intro:   Professional water rocket guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
step 1:   Lets get Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
step 2:   How to build a fins and nose cones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
step 3:   Step 2 of nose cone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
step 4:   step 3 of nosecone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
step 5:   Fins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
File Downloads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
step 6:   glue or tape the fins on to the rocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
step 7:   Now for the professional water rockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
step 8:   Splicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
step 9:   Launchers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
File Downloads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
step 10:   Launcher parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
step 11:   how to make the launcher and nozzles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
File Downloads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
step 12:   Two Stage rockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
step 13:   Stager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
step 14:   Drop away boosters! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
step 15:   Advanced fins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
File Downloads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
step 16:   payloads and parachutes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
step 17:   step 1,2,3,4 of parachutes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
step 18:   Payloads steps 1,2,3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
step 19:   rocket designs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
step 20:   Thank you for Reading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Related Instructables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Advertisements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Comments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
http://www.instructables.com/id/Professional-water-rocket-guide/
Author:   oscarthompson
Author:  oscarthompson
I like to make instructables which are fun to build or make. I'm instrested in rockets, rc planes, science and fishing. send me a message if you have any
questions.
License:   Attribution Non-commercial (by-nc)
Intro:  Professional water rocket guide
This Instructable will show you the how to build and fly water rockets. Featuring two stage rockets and drop away boosters, and also some basics.
This instructable is based on my knowledge of water rockets, that I have learn in the past few years.
I am not responsible for any damage you infict on your self or others from launching or building water rockets
Have fun building and flying!
Image Notes
1. Tri-launcher
2. My rocket (polaron I) Thanks air command!
3. tommy timmer release mechanism
step 1: Lets get Started
A water rocket is propelled by pressurised air forcing water down though a nozzle. This creates thrust.
If you took a standard two litre fizzy soft drink bottle and pressurised it to120 psi the rocket would reach about 100 or so feet.
But then if you took 2, two litres bottles and pressurised it to 120 psi again the rocket would go about 150 feet or so because the rocket has more air in it therefore
creating more thrust. The rocket will only go 50 feet more because of the added wieght. You can stop this by making a two stage rocket. A two stage rocket will work
better because it would not have to carry the full payload on all of its flight.
http://www.instructables.com/id/Professional-water-rocket-guide/
http://www.instructables.com/id/Professional-water-rocket-guide/
step 2: How to build a fins and nose cones
In the next few steps you will be shown how to build the basic needs of a bottle rocket.
This step is to get to grips on what a rocket needs.
Step 1: nose cone
cut the top and bottom off a 1.25 litre bottle. Then cut the neck off the top.
step 3: Step 2 of nose cone
Step 2:
Cut a ping pong ball in half with a craft knife and then
glue half of the ping pong ball into the top of the 1.25 bottle top.
step 4: step 3 of nosecone
Glue the nose cone to the top of the rocket, You could also tape it.
The rocket should now be ready for flight.
http://www.instructables.com/id/Professional-water-rocket-guide/
step 5: Fins
This stage is still the basics of how to make a water rocket but may help in later projects.
step 1:
Print off the fin template from the link below
then glue the fin on to cardboard or use it as a template for corregated plastic and let the glue set.
File Downloads
fin diagram 2.doc (21 KB)
[NOTE: When saving, if you see .tmp as the file ext, rename it to 'fin diagram 2.doc']
step 6: glue or tape the fins on to the rocket
All you need to do now is glue or tape the fins to the rocket.
http://www.instructables.com/id/Professional-water-rocket-guide/
step 7: Now for the professional water rockets
Professional water rockets can vary from big one stage rockets to 2 stage rockets with drop away boosters.
This stage of the instructable will show you how to make a big one stager and how to couple or splice bottles together.
step 1 : coupling and splicing
How to couple bottles
first drill a hole about 7-8mm in width in the bottom of one of your bottles.
Next screw the male end of a plumbing coupling which is about 8mm in width into the bottom of the bottle, then seal it with a sealent glue. Next drill an 8mm hole in the
other bottle cap and then insert the male end in to it. Whist the bottle cap is off the bottle, screw the female end into the other side of the bottle cap (side facing the inside)
If you want you can seal it with glue as well.
http://www.instructables.com/id/Professional-water-rocket-guide/
Image Notes
1. 8mm coupler
http://www.instructables.com/id/Professional-water-rocket-guide/
step 8: Splicing
How to splice
To join two bottles together like in the picture to create an air tight seal you need three bottles
first cut the bottom ends off two of the same sized bottlles
Then cut both ends of the same sized third bottle and place that in the two exposed ends of the bottle
Next glue the third bottle in the 2 exposed ends.
step 9: Launchers
The laucher that my water rockets are made for was designed by Nasa.
The launcher lets you vary the nozzle size so you can get better performance from your rocket.
The next few steps will show you how to make it.
Update:
PDF from NASA  below
http://www.instructables.com/id/Professional-water-rocket-guide/
File Downloads
bottle_rocket_launcher.pdf ((612x792) 87 KB)
[NOTE: When saving, if you see .tmp as the file ext, rename it to 'bottle_rocket_launcher.pdf']
step 10: Launcher parts
Below are the materials you will need for the launcher
qty part
1 1/2 inch wood (any type)
2 10mm bolts
1 10mm metal drillbit
1 10mm wood drillbit
6 10mm nuts and washers
1 presta bike valve (you can get this from an old inner tube)
1 rubber bung
1 bike pump
2 tent pegs
4 L (shaped) brackets
2 nails
http://www.instructables.com/id/Professional-water-rocket-guide/
step 11: how to make the launcher and nozzles.
below is the link for the pdf for making the launcher.
The launcher can hold any type of pressure depending on the rubber bung.
If you have a different nozzle size then you can adjust the nuts on the bolts so the pins can line up with the hole in the 90 degree mending plate and the neck of the
bottle.
File Downloads
bottle_rocket_launcher.pdf ((612x792) 87 KB)
[NOTE: When saving, if you see .tmp as the file ext, rename it to 'bottle_rocket_launcher.pdf']
step 12: Two Stage rockets
The mechanisim I use to stage my rocket is different to Air Commands or any other two stage water rocket.
I have tried to make the stager compact. The stager can link to a servo or a pressure switch.
The instructions for it are on the next few steps.
http://www.instructables.com/id/Professional-water-rocket-guide/
Image Notes
1. I finally made a diagram by myself
2. half a ring goes on the clip here
step 13: Stager
Materials
QTY Material
1 22mm pipe any lenth over 15cm
1 plywood (any size under 10mm) or you can use plastic
1 inline non return valve..... One from a ballon pump will do
1 a 1st stage of a bottle rocket and a 2nd
instructions
1. insert 2cm of the 22mm pipe in to the 1st stage. ( pic1)
2. use epoxy or pvc sement to seal it. (pic 1)
3. insert a non return valve into the pipe and glue it.
3.work out the dimensions of how long and wide the plywood or plastic needs to be and then cut it out using image 2 to help you. The hinge is mounted on the pipe
clamp.
4.when you slide the bottle on (use vaseline to seal it) make sure the pipe clamp is right next to the neck on the first stage. This will have your hinge on, next clip your
hinge onto the bottle neck so it is tight and won't fall off.
http://www.instructables.com/id/Professional-water-rocket-guide/
Image Notes
1. I finally made a diagram by myself
2. half a ring goes on the clip here
http://www.instructables.com/id/Professional-water-rocket-guide/
step 14: Drop away boosters!
These boosters are so easy to make because they are only held on by the upthrust of the bottles.
These drop away boosters are differernt to Air Commands.
For the drop away boosters you will have to make three of the launchers.
Instructions(drop away boosters)
1.measure your drop away booster bottles against your main rocket. Make a mark (dot or line) where the top of the booster meets on your rocket.
2.use pic 1 to help you, where you marked a dot on the booster glue the advanced fins together and stick the bottom of the fins on the marked dot with duck tape or glue.
The Advanced fin template is on step 15.
3. test the rocket!
Image Notes
1. NPL water rocket challange (I go to it)
http://www.instructables.com/id/Professional-water-rocket-guide/
Image Notes
1. 2 fins glued together
2. The bottles push up against the fins giving the rocket a "boost"
3. bottom of bottle goes into bung
step 15: Advanced fins
These advanced fins are for bigger rockets and are very good for two stage rockets and rockets with drop away boosters.
for fins print off the template below
File Downloads
http://www.instructables.com/id/Professional-water-rocket-guide/
fin diagram 3.doc (24 KB)
[NOTE: When saving, if you see .tmp as the file ext, rename it to 'fin diagram 3.doc']
step 16: payloads and parachutes
The next few steps will show you how to make a parachute system followed on by a payload bay
Parachutes:
The parachute system used by me 'OscarThompson' is a simple gravitational deployment.
The nose cone is fitted on the rocket loosely and when the rocket reaches its maximum altitude the rocket will fall back to earth nose first and as the nose has a weight in
it, it falls off deploying the parachute inside.
Image Notes
1. parchute is loosely fitted inside the nose cone
2. payload section
step 17: step 1,2,3,4 of parachutes
Step one:
Find a payload bay for your rocket. any size to fit a parachute
step two:
Build a nose code like as shown in steps 2 and 3. Your nose cone either needs to fit loosely on top of the payload bay or loosely in it.
step Three:
cut a hole in the payload bay and the nose cone so a string can fit though it and be knotted.
step four:
tie the parachute string to the string you have tied to the nose cone and the payload bay.
http://www.instructables.com/id/Professional-water-rocket-guide/
http://www.instructables.com/id/Professional-water-rocket-guide/
step 18: Payloads steps 1,2,3
Payloads
payloads are used to carry equipment such as altitude meters, accellerometers or even a slug (wierd, but the g-forces can kill it!)
Step one:
cut the bottom off any size bottle.
step two
cut two disks the same width as the bottle out of corregated plastic
step three
cut a strip out of plastic the same width as the bottle but a little bit smaller in length than the bottle
Step four:
Glue them together and when dry put your payload into the payload section of the rocket.
Image Notes
1. Step two disks
http://www.instructables.com/id/Professional-water-rocket-guide/
step 19: rocket designs
You are free to look at these pictures if you need help for a design.
Image Notes
1. NPL water rocket challange (I go to it)
http://www.instructables.com/id/Professional-water-rocket-guide/
Image Notes
1. eight litre (four two litre bottles)
step 20: Thank you for Reading
If you have any problems please leave a comment
http://www.instructables.com/id/Professional-water-rocket-guide/
Related Instructables
Water rocket
safty by
oscarthompson
Water Rocket
Challenge (for
instructable
members!) by
oscarthompson
Water bottle
rocket by
mjnhbg3
Water Rocket
Launch Abort
Valve by
air.command
Pneumatic
Rocket
Launcher
(slideshow) by
sstables42
The C3.2 Lego
Crossbow-
Rocket
Launcher by
Bitterberry9
Vinegar
Bazooka by
Spl1nt3rC3ll
8 litre water
rocket (genesis
I rocket) by
oscarthompson
Advertisements
Comments
50 comments Add Comment view all 69 comments
 jason.buckmann says:  Apr 26, 2010. 5:35 PM  REPLY
who cares if he has a copyright?!?!? this is a great instructable that i used to spend a few hours with my daughter AND an instructional speech for my
speech class. but the instructions you put on here were clear and easy to read. and i researched the launcher online for several hours and i believe this to be
the best one.
i used the 2 bottle design and i used gorilla glue (which is stronger than hot glue). the thing reached 15 to 20 feet in the air and the reason for this failure was
my choice of glue. the glue expanded like it is designed to BUT this glue is not a good adhesive for the plastic in the bottles.
i can see the potential if i just follow instructions (this was a problem for me growing up). i always think i can improve the process, but once again i am wrong.
but my daughter had an awesome time, i had a great time, and we got the whole family together for the launch so the project was still an overall success. i
will be building bigger and better in the near future.
thanks for the great instructable oscarthompson!
 chbue070780 says:  May 16, 2010. 9:52 PM  REPLY
I used to make make water rockets when I was a kid.  All I ever used was a 2 liter bottle, duct tape, and the valve stem from a tire.  Drill a hole just
slightly smaller than the valve stem in the plastic lid and jam the sucker through it as far as you can, wrap the bottle with duct tape (just one layer is fine) -
this is a "better safe than sorry kinda thing" -  never had one blow up.  Fill the bottle about 1/5 of the way with water, use a hand pump or air compressor
to add about 45 psi, turn upside down and unscrew the lid.  Mine usually went above 100 feet easy, of course I used a bit more pressure.  ;)
 oscarthompson says:  Apr 27, 2010. 9:18 AM  REPLY
Thanks, you made my day !
 ducttape11x says:  Apr 16, 2010. 5:25 PM  REPLY
I'm gus this does not go high   it looks to big to go high!!! But any way sweet!!! 5stars!!!!!!!!
 Lowney says:  Apr 7, 2010. 10:32 AM  REPLY
Can we see a video of your big rocket?
 firezone says:  Dec 20, 2009. 11:54 AM  REPLY
do you actually own the copyright to these diagrams, i highly doubt you have gone through what is needed to have the copyright for them and putting that
little "copyright OscarThompson" in your pictures doesn't actually do anything
 Ian01 says:  Mar 5, 2010. 8:49 PM  REPLY
I'm pretty sure you get copyright automatically, even if you don't claim it.
 oscarthompson says:  Dec 20, 2009. 12:35 PM  REPLY
I have only put it in so people can't use my pictures, unless they want my name on it. The my pictures as i drew them on paint, it really doesn't matter too
much that i havn't copyrighted them.
Thanks
Oscar
http://www.instructables.com/id/Professional-water-rocket-guide/
 max0506 says:  Feb 7, 2010. 1:19 AM  REPLY
what do you mean with rubber bung in the part list of step 10
 oscarthompson says:  Feb 7, 2010. 2:13 AM  REPLY
rubber bungs like the ones in wine bottle's but rubber. Type it in to google images
Thanks
Oscar
 max0506 says:  Mar 5, 2010. 2:03 PM  REPLY
I see thanx
 juanpedro132 says:  Feb 23, 2010. 9:45 AM  REPLY
i like the idea but i don't konw anything.
How can i do for fill the boosters?
do i have to put their a valvle each?
and are the boosters gonig to fall down?
if yeah how will i do it ?
thanks for the  ideas.
 oscarthompson says:  Feb 24, 2010. 10:08 AM  REPLY
You can fill the boosters by putting the water in the top of the bottle. The bicycle valave will help prevent leakage.
The boosters will fall down when the thrust of the booster can no longer beat the air resistance thus gravity pulling the booster down.
This can be achieved by making three of the launch mechanism's just on one Pad ( two for boosters one for main)
Oscar
 raynman217 says:  Dec 4, 2009. 12:13 PM  REPLY
good so far, but the diagram for this step cannot be viewed properly at the current size, and even when viewed at the right size, it is very hard to understand.
 m_debator says:  Nov 25, 2009. 9:30 PM  REPLY
This is AWESOME!  Its the John Holmes of water bottle rockets.
 gingerlad95 says:  Nov 17, 2009. 11:55 AM  REPLY
what is the materials list for this project
 oscarthompson says:  Nov 18, 2009. 9:47 AM  REPLY
Which part of the project?
 gingerlad95 says:  Nov 19, 2009. 11:33 AM  REPLY
all of it
we need to know the materials list for everything SO WE CAN DO THE PROJECT...
AND PASS OUR CLASS
 oscarthompson says:  Nov 19, 2009. 1:55 PM  REPLY
First your going to need about 10+, two l bottles to start
For the launcher you will need;
qty part
1 1/2 inch wood (any type)
2 10mm bolts
1 10mm metal drillbit
1 10mm wood drillbit
6 10mm nuts and washers
1 presta bike valve (you can get this from an old inner tube)
1 rubber bung
1 bike pump
2 tent pegs
4 L brackets
1 mending plate
2 nails
For rockets you will need;
corex (corregated plastic)
http://www.instructables.com/id/Professional-water-rocket-guide/
ducktape
pl premuim or another pressure rated strong adhesive
ping pong balls
1.25 l bottles
For parachute mechanism;
You can use my nose cone drop of deployment or a tomy timer release mechansim avible with the link.
For the tomy timer release mec you will need;
Tomy timer (wind up toy)
plastic or synthetic fabric
string
glue
rubber band(s)
For the staging (which would be advised to be not for biggerners)
22mm pipe
hinges
basla or ply wood
m4 bolts
string
tomy timer or servo
Thats about it, But how long do you have to do this?
And if your just biggening water rockets I would advise you to not do multi stage or drop away booster rockets.
Thanks
Oscar
 gingerlad95 says:  Nov 17, 2009. 11:43 AM  REPLY
what is the materials list for this project
 gingerlad95 says:  Nov 17, 2009. 11:41 AM  REPLY
what is the materials list for this project
 Bartboy says:  Oct 24, 2009. 1:06 PM  REPLY
I was wondering what you meant by "professional" when I clicked on this.
I don't anymore....
Some of those rockets look really awesome!
How big is the biggest water rocket you've ever made?
 oscarthompson says:  Oct 25, 2009. 1:03 AM  REPLY
The picture (on the intro) is the biggest one I have ever mad. Its the polaron I from air command.
Thanks
Oscar
 Bartboy says:  Oct 25, 2009. 6:57 AM  REPLY
It looks really awesome!
I'd like to see the biggest one ever made, but with a quick google search I couldn't find a name.
What is the biggest water rocket ever made?
 Kinnishian says:  Nov 15, 2009. 8:30 AM  REPLY
 If you count hydrogen oxygen rockets whose exhaust is H20... :)
 Bartboy says:  Nov 15, 2009. 8:35 AM  REPLY
Right... :P
 milo0is0hot0 says:  Oct 31, 2009. 3:32 AM  REPLY
GREAT INSTRUCTABLE!!!! I WAS GOING TO USE THIS TO TAKE PART IN THE NPL COMMPETION....AND I WAS HOPING TO WIN!!! BUT AS YOUR
TAKING PART :( I HAVE BEEN A FEW TIMES AND ITS GREAT THERE LOADS OF FREEBIES AND STUFF...BUT ALL MY ATTEMPTS AT WATER
ROCKETS NAMELY THE RELEASE MECHANISM HAVE FAILED...[UNTIL NOW] I THINK YOUR RELEASE MECHANISM LOOKS GREAT EXCEPT I
WILL TRY TO DO IT IN COPPER SO ITS NOT [EXPLOSIVE] WHEN TOO MUCH PREASURE IS APLLIED!!!!
http://www.instructables.com/id/Professional-water-rocket-guide/
 oscarthompson says:  Nov 10, 2009. 10:19 AM  REPLY
Thanks for your comment, I hope to here more about your rockets..... what's your team name in the compition (if you don't mind me asking) because the
results are on the website so I can look you up. I can't belive, I found some one who goes to it now, and i only started going to it this year.
Oscar
 oscarthompson says:  Oct 29, 2009. 11:52 AM  REPLY
Nasa Don't produce the PDF anymore but i have this link to it -> http://quest.nasa.gov/space/teachers/rockets/act10.html.
I do have the PDF saved on my computer but its broken down so in the slightist hope i may get the PDF to you tonight but if not, in the next week or so. If
you dont get it by then i dont have it.
Sorry
Oscar
 thefutureisnow says:  Oct 29, 2009. 8:54 PM  REPLY
Here's a page by a science teacher on bottle rockets. www.lnhs.org/hayhurst/rockets/  He has a lot of step by step instructions and pictures. I followed all
his instructions and it worked everytime. I have a lot of info on bottle rocketry I can e-mail you if you want.
 thefutureisnow says:  Oct 29, 2009. 8:47 PM  REPLY
Awesome instructable! I used to be into water bottle rockets for awhile. I launched 2 liter bottles, 1 liter bottles, and even the little 6 oz bottles. I stopped after
my launcher broke down. I had to make several mods to keep it functioning and finally the seals blew and it couldn't handle more than 70 psi.  
 TheMoonMaster says:  Oct 29, 2009. 7:36 PM  REPLY
I want to take a bunch of 250 ml small bottles and do this but put the launcher in a PVC pipe and cap the back so the added pressure will compensate for the
smaller bottle. Do you think this would work?
If it does, Bazooka/Mortar!
 morgano says:  Oct 29, 2009. 9:47 AM  REPLY
This is great!  I'd like to see more info on building the launcher, though.  That's kind of the crucial part, isn't it?  I'm getting ready to do this with my science
class next week.  We've done it before with a different launcher, and this one looks more stable.  
 oscarthompson says:  Oct 29, 2009. 11:38 AM  REPLY
Sure, I will get you the info...
Its a PDF from the NASA website
 sturmey says:  Oct 29, 2009. 8:20 AM  REPLY
I like the idea for a second stage, but the picture is hard to read. Could you write that information into the text, or use a larger font on the picture?
I do like the instructable, but figuring out the second stage is tricky.
 oscarthompson says:  Oct 29, 2009. 11:37 AM  REPLY
i'll try to get the font bigger but it may take a week or so as im waiting to get the files back on to my computer (im working off a laptop with none off my
files on because my computer broke down)
Sorry.
Oscar
 haclil says:  Oct 25, 2009. 2:04 AM  REPLY
 Oscar, thanks very much for your reply on PL Premium and other glues, very informative!
 oscarthompson says:  Oct 25, 2009. 1:09 AM  REPLY
Sorry everyone-
My computer has crashed and its dead....Im still waiting to get my files off the hard drive, so I may not reply for a week or so  and i can't post images or
videos unless I take them from my camera. I am working from a laptop which has one of my files on. It won't connect to my wireless router so i have
connected it via ethernet cable which is so! slow!
 haclil says:  Oct 24, 2009. 2:39 PM  REPLY
 About glues:  You say in one of your replies that you use "pl premium" glue.  I am not at all familiar with that glue.  In fact, I don't know of any glues for the
PET plastic of these bottles.
Could you please expand on the subject of glues?
http://www.instructables.com/id/Professional-water-rocket-guide/
 oscarthompson says:  Oct 25, 2009. 1:01 AM  REPLY
The glue that should be used for PET Plastic bottles are glues that are recommended for plastic and are also pressure rated. PL Premium is plyurathane
glue which makes a strong seal which is excellent for water rockets. although this isn't widely available so I use bostik soft plastic glue, you can get it in
any hardware store and on the side it should say; its sutible for plastics and it's water proof, it should also come with some pvc plastic. This glue actually
dissolves the two bottles together to create a strong seal.
Thanks
Oscar
 lemonie says:  Oct 23, 2009. 2:10 PM  REPLY
Post the video again - it shows these thing work (rather well) and rotate the landscape images.
L
 red9er says:  Oct 4, 2009. 11:52 AM  REPLY
i'm not quite getting how this lock releases. also could you explain the purple item on step 13 and how it latches to the 2nd stage?
 oscarthompson says:  Oct 5, 2009. 12:12 AM  REPLY
The lock, that latches on to the 2nd stage is pulled by a servo or a tommy timer. A string is tied to the top of it (above the hinge, marked in black) and
when it is pulled it releases. You will need a strong servo to do this though. The purple item, (clip around the bottle neck) pushes on to the lip of the
bottle. If you took a ring a sliced it in half, you could fit it round the bottle neck securly, attached to the clip. I have marked it on thee picture now.
 starburst552 says:  Sep 6, 2009. 3:40 PM  REPLY
Hey, i read the whole thing (and printed out sections) and i know what i'm going to do this week! awesome instructable, explained well and good ideas!!!!! 5
Stars to this!
 oscarthompson says:  Sep 7, 2009. 11:10 AM  REPLY
Thanks so much.
 starburst552 says:  Sep 7, 2009. 11:19 AM  REPLY
no problem!
 Shephyr says:  Aug 22, 2009. 3:09 PM  REPLY
Do you have any idea on how to make the launcher lean 45 degrees XD?
 oscarthompson says:  Aug 30, 2009. 2:29 AM  REPLY
Year just put wooden blocks under it to lean it
 Yukondano2 says:  Aug 25, 2009. 9:09 PM  REPLY
O_O Holy crap that is BIG I want one! This is quite complicated, How much would it take to build the one in the picture?
 oscarthompson says:  Aug 30, 2009. 2:27 AM  REPLY
For the rocket about 10 £ but fir the launch pad about 30 or less £
view all 69 comments

Sponsor Documents

Or use your account on DocShare.tips

Hide

Forgot your password?

Or register your new account on DocShare.tips

Hide

Lost your password? Please enter your email address. You will receive a link to create a new password.

Back to log-in

Close