Programming Guide for Vizia + Dimmers and Quiet Fan Speed Control
Alarm Grid is an alarm monitoring company with an emphasis on affordable alarm monitoring, great customer service, and diy consumers interested in building their own home security systems. If you are looking for a home security system, a business security system, or an alarm system for your apartment or condo, let us guide you through the process of purchasing the equipment that is right for your space, and the monitoring that is right for your equipment.
Content
TECHNICAL APPLICATION NOTE
Programming Guide for Vizia + Dimmers and Quiet Fan Speed Control
VIZIA + DIMMERS PROVIDE THE FOLLOWING ADVANCED PROGRAMMING FEATURES: I. DIMMER PROGRAMMING SECTION A
• Energy Save - Set the maximum brightness level for energy savings • Minimum Brightness Level – Set the minimum dimming level • Preset ON Level – Set the turn on brightness level regardless of the previous set light level (formerly Dim Lock) • Almost OFF Level – Sets the brightness level the device will dim the lights to when the push pad is pressed to turn OFF. In this mode the lights will always remain ON at a reduced energy consumption level. • ON Fade Rate – Set the amount of time in seconds it takes the lights to turn ON to maximum brightness • OFF Fade Rate – Set the amount of time in seconds it takes the lights to turn OFF from maximum brightness • LED Options – Set the time period in seconds the Locator LED and Brightness Display will stay lit before extinguishing • Restore Defaults – Restores the factory default settings
LED Brightness Display
Dim/Bright Bar
Push Pad
VPI06
Locator Light
APPLICABLE CAT. NUMBERS
VPI06, VPM06, VPM10, VPE04, VPE06, VPX10, VPZX12-7, VPH08, VPH06-7
MODE A-1 A-2 A-3 A-4 B-1 B-2 B-3 C ADVANCED FEATURES SUMMARY DESCRIPTION RANGE Energy Save 100% - 75% Minimum Brightness Level 1% - 50% Preset On Level 1% - 100%, not active Almost OFF Level 1% - 50% On Fade Rate 0s – 25s OFF Fade Rate 0s – 25s LED Options Active, turn off after 5s Restore Defaults DEFAULT 100% LED 2 Not active Not active 0.5 seconds 0.5 seconds Active
SECTION B
Leftmost LED = LED 1 Rightmost LED = LED 7
Leviton Mfg. Co., Inc.
59-25 Little Neck Pkwy, Little Neck, NY 11362-2591 Tech Line: 1-800-824-3005 Fax: 1-800-832-9538 www.leviton.com
© 2008 Leviton Manufacturing Co., Inc. All rights reserved. Subject to change without notice.
Vizia +™ Programming Guide
Section C Dimmer Programming
VPI06, VPM06, VPM10, VPE04, VPE06, VPX10, VPX12, VPH08, VZH06 NOTES: • Have a flashlight handy if this dimmer controls the only light source in the room • The device will exit programming mode after 3 minutes of inactivity • Pressing the Push Pad at any time during programming will advance the device to the next programming mode. A-3) The Locator LED will blink 3 times per second to indicate Program Mode A-3, Preset ON Level. To change the current Preset ON Level from 1-100%, use the DIM/BRIGHT Bar. If this feature is not desired, press and^ hold the left half of the DIM/BRIGHT Bar ( ) until no LED is lit (default setting). By tapping the Push Pad this setting will automatically be saved and the device will advance to the next programming mode, A-4. A-4) The Locator LED will blink 4 times per second to indicate Program Mode A-4, Almost OFF Level. To change the current Almost OFF Level, use the DIM/BRIGHT Bar to adjust the preset light level. If this feature is not desired, press and hold the right half of the DIM/BRIGHT Bar (^) until no LED is lit (default setting). Almost OFF can be overridden by pressing ^and holding the left half of the DIM/BRIGHT Bar ( ) until the lights turn off. By tapping the Push Pad this setting will automatically be saved and the device will exit Programming Mode A. Note: When Almost OFF Level is set the LED Locator will be illuminated when the dimmer is in the Almost OFF state, even though the light remains on at a reduced energy consumption level.
Program Mode A
To enter Program Mode A: Push and hold the Push Pad and then the right half of the DIM/BRIGHT Bar (^) for 5 seconds until the Locator LED and leftmost LED (LED 1) begin to blink.
Vizia +™ Programming Guide
A-1) Upon releasing the Push Pad and the right half of the DIM/BRIGHT Bar (^) , the Locator LED will continue to blink once per second and the rightmost LED will illuminate to display the device is in Program Mode A-1, Energy Save. To change the Energy Save Level, use the DIM/BRIGHT Bar to move the corresponding LED to the desired discrete preset level according to Chart A. By tapping the Push Pad this setting will automatically be saved and the device will advance to the next programming mode, A-2. CHART A
LED LED 1 LED 2 LED 3 LED 4 LED 5 LED 6 LED 7 (Default) ADVANCED FEATURES SUMMARY MAXIMUM BRIGHTNESS ENERGY SAVINGS 75% 34% savings 80% 29% savings 85% 24% savings 90% 16% savings 95% 8% savings 97% 5% savings 100% (full bright) 0 % Savings
Program Mode B
To enter Program Mode B: Push and hold the ^ Push Pad and then the left half of the DIM/BRIGHT Bar ( ) for 5 seconds until the Locator LED and rightmost LED (LED 7) begin to blink. B-1) Upon releasing the Push Pad, the Locator LED will continue to blink once per second indicating the dimmer is in Program Mode B-1, ON Fade Rate. To change the ON Fade Rate, use the DIM/BRIGHT Bar to move the LED to the desired preset level according to Chart B. By tapping the Push Pad this setting will automatically be saved and the device will advance to the next programming mode, B-2. B-2) The Locator LED will blink 2 times per second to indicate Program Mode B-2, OFF Fade Rate. To change the OFF Fade Rate, use the DIM/BRIGHT Bar to move the LED to the desired preset level according to the Chart B. By tapping the Push Pad this setting will automatically be saved and the device will advance to the next programming mode, B-3. CHART B
LED LED 1 LED 2 (Default) LED 3 LED 4 LED 5 LED 6 LED 7 FADE ON 0 seconds (instant) 0.5 seconds 1.5 seconds 3 seconds 6 seconds 10 seconds 25 seconds FADE OFF 0 seconds (instant) 0.5 seconds 1.5 seconds 3 seconds 6 seconds 10 seconds 25 seconds
A-2) The Locator LED will blink 2 times per second to indicate the device is in Program Mode A-2, Minimum Brightness Level. To change the Minimum Brightness Level from 1-50%, use the DIM/BRIGHT Bar. The light output will reflect the minimum brightness level selected. By tapping the Push Pad this setting will automatically be saved and the device will advance to the next programming mode, A-3.
Leviton Mfg. Co., Inc.
59-25 Little Neck Pkwy, Little Neck, NY 11362-2591 Tech Line: 1-800-824-3005 Fax: 1-800-832-9538 www.leviton.com
© 2008 Leviton Manufacturing Co., Inc. All rights reserved. Subject to change without notice.
B-3) The Locator LED will blink 3 times per second to indicate Program Mode B-3, LED Options. To change the LED Options settings, use the DIM/BRIGHT Bar to move the LED to the desired preset setting according to the chart below. By tapping the Push Pad this setting will automatically be saved and the device will exit Programming Mode B
Program Mode C
To enter Program Mode C: Engage the air-gap switch by gently pressing the top of the Push Pad until the bottom lifts completely out of the frame and a click is heard. All LEDs will extinguish. C) Press Push Pad back into the frame and hold for 7 seconds until and the LED Brightness Display starts bi-directional strobing to indicate Program Mode C, Restore Default. To Restore Default settings, release the Push Pad. This will save defaults settings and exit Programming Mode C.
LED OPTIONS CHART
LED LED 1 LED 2 LED 3 LED 4 LED 5 LED 6 LED 7 LOCATOR LED TIMEOUT Active Active Turns off 5 seconds after use Turns off 5 seconds after use N/A N/A N/A LED BRIGHTNESS DISPLAY OPTIONS Active Turns off 5 seconds after use Active Turns off 5 seconds after use N/A N/A N/A
SWITCH PROGRAMMING
• LED Option - Sets the Locator LED timeout to 5 seconds after use. NOTE: The switch will exit program mode after 3 minutes of inactivity
Program Mode
To enter Program Mode: Push and hold the Push Pad for 10 seconds until the Locator LED begins to blink. Upon releasing the Push Pad, the LED Option will automatically be changed.
LOCATOR LED Default First toggle LOCATOR LED OPTION SETTING Active Turns off 5 seconds after use
Push Pad
VPS15
Locator Light
Leviton Mfg. Co., Inc.
59-25 Little Neck Pkwy, Little Neck, NY 11362-2591 Tech Line: 1-800-824-3005 Fax: 1-800-832-9538 www.leviton.com
© 2008 Leviton Manufacturing Co., Inc. All rights reserved. Subject to change without notice.
Vizia +™ Programming Guide
FAN SPEED CONTROL PROGRAMMING Program Mode A
LED Brightness Display
Fan Speed Bar
To enter Program Mode A: Push and hold the Push Pad and then the right half of the FAN SPEED Bar (^) for 5 seconds until the Locator LED and leftmost LED (LED 1) begin to blink. The Locator LED will blink once per second to indicate Program Mode A, Preset ON Level. To change the current Preset ON Level from HIGH (LED 7), MEDIUM (LED 4) or LOW (LED 1), use the FAN SPEED Bar. If this feature is not desired, ^ press and hold the left half of the FAN SPEED Bar ( ) until no LED is lit (default setting). By tapping the Push Pad this setting will automatically be saved and the device will exit Programming Mode A.
Program Mode B
Push Pad
Vizia +™ Programming Guide
Locator Light
VPF01 • Preset ON Level – Set the turn on fan speed regardless of the previous set level • LED Options – Set the time period in seconds the Locator LED and Fan Speed will stay lit before extinguishing • Restore Defaults – Restores the factory default settings (including device load ON at maximum level)
MODE A B C ADVANCED FEATURES SUMMARY DESCRIPTION RANGE Preset On Level 1% - 100%, not active LED Options Active, turn off after 5s Restore Defaults DEFAULT Not active Active
To enter Program Mode B: Push and hold the Push ^ Pad and then the left half of the FAN SPEED Bar ( ) until the rightmost LED (LED 7) begins to blink. The Locator LED will blink 2 times per second to indicate Program Mode B, LED Options Mode. To change the LED Options settings, use the FAN SPEED Bar to move the LED to the desired preset setting according to the chart below. By tapping the Push Pad this setting will automatically be saved and the device will exit Programming Mode B.
LED LED 1 (Default) LED 3 LED 7 LED LOCATOR TIMEOUT Active Active Turns off 5 seconds after use LED BRIGHTNESS DISPLAY TIMEOUT Active Turns off 5 seconds after use Turns off 5 seconds after use
Program Mode C
To enter Program Mode C: Engage the air-gap switch by gently pressing the top of the Push Pad until the bottom lifts completely out of the frame and a click is heard. All LEDs will extinguish. Press Push Pad back into the frame and hold Push Pad for 7 seconds until the LED Brightness Display starts bi-directional strobing to indicate Program Mode C, Restore Default. Releasing the Push Pad will Restore Default settings and exit programming mode.
Vizia +™ is a trademark of Leviton Manufacturing Co., Inc. Covered by one or more U.S. and Foreign Patents and patents pending.
NOTES: • The device will exit program mode after 3 minutes of inactivity • Pressing the Push Pad at any time during programming will advance the device to the next programming mode.
Leviton Manufacturing Co., Inc.
59-25 Little Neck Parkway, Little Neck, NY 11362-2591 Telephone: 1-800-323-8920 • FAX: 1-800-832-9538 • Tech Line (8:30AM-7:30PM E.S.T. Monday-Friday): 1-800-824-3005
Leviton Manufacturing of Canada, Ltd.
165 Hymus Boulevard, Pointe Claire, Quebec H9R 1E9 • Telephone: 1-800-469-7890 • FAX: 1-800-563-1853
Leviton S. de R.L. de C.V.
Lago Tana 43, Mexico DF, Mexico CP 11290 • Tel. (+52) 55-5082-1040 • FAX: (+52) 5386-1797 • www.leviton.com.mx
Visit our Website at: www.leviton.com
© 2008 Leviton Manufacturing Co., Inc. All rights reserved. Subject to change without notice. G-7904/J7-tp
Programming Guide for Vizia + Dimmers and Quiet Fan Speed Control
VIZIA + DIMMERS PROVIDE THE FOLLOWING ADVANCED PROGRAMMING FEATURES: I. DIMMER PROGRAMMING SECTION A
• Energy Save - Set the maximum brightness level for energy savings • Minimum Brightness Level – Set the minimum dimming level • Preset ON Level – Set the turn on brightness level regardless of the previous set light level (formerly Dim Lock) • Almost OFF Level – Sets the brightness level the device will dim the lights to when the push pad is pressed to turn OFF. In this mode the lights will always remain ON at a reduced energy consumption level. • ON Fade Rate – Set the amount of time in seconds it takes the lights to turn ON to maximum brightness • OFF Fade Rate – Set the amount of time in seconds it takes the lights to turn OFF from maximum brightness • LED Options – Set the time period in seconds the Locator LED and Brightness Display will stay lit before extinguishing • Restore Defaults – Restores the factory default settings
LED Brightness Display
Dim/Bright Bar
Push Pad
VPI06
Locator Light
APPLICABLE CAT. NUMBERS
VPI06, VPM06, VPM10, VPE04, VPE06, VPX10, VPZX12-7, VPH08, VPH06-7
MODE A-1 A-2 A-3 A-4 B-1 B-2 B-3 C ADVANCED FEATURES SUMMARY DESCRIPTION RANGE Energy Save 100% - 75% Minimum Brightness Level 1% - 50% Preset On Level 1% - 100%, not active Almost OFF Level 1% - 50% On Fade Rate 0s – 25s OFF Fade Rate 0s – 25s LED Options Active, turn off after 5s Restore Defaults DEFAULT 100% LED 2 Not active Not active 0.5 seconds 0.5 seconds Active
SECTION B
Leftmost LED = LED 1 Rightmost LED = LED 7
Leviton Mfg. Co., Inc.
59-25 Little Neck Pkwy, Little Neck, NY 11362-2591 Tech Line: 1-800-824-3005 Fax: 1-800-832-9538 www.leviton.com
© 2008 Leviton Manufacturing Co., Inc. All rights reserved. Subject to change without notice.
Vizia +™ Programming Guide
Section C Dimmer Programming
VPI06, VPM06, VPM10, VPE04, VPE06, VPX10, VPX12, VPH08, VZH06 NOTES: • Have a flashlight handy if this dimmer controls the only light source in the room • The device will exit programming mode after 3 minutes of inactivity • Pressing the Push Pad at any time during programming will advance the device to the next programming mode. A-3) The Locator LED will blink 3 times per second to indicate Program Mode A-3, Preset ON Level. To change the current Preset ON Level from 1-100%, use the DIM/BRIGHT Bar. If this feature is not desired, press and^ hold the left half of the DIM/BRIGHT Bar ( ) until no LED is lit (default setting). By tapping the Push Pad this setting will automatically be saved and the device will advance to the next programming mode, A-4. A-4) The Locator LED will blink 4 times per second to indicate Program Mode A-4, Almost OFF Level. To change the current Almost OFF Level, use the DIM/BRIGHT Bar to adjust the preset light level. If this feature is not desired, press and hold the right half of the DIM/BRIGHT Bar (^) until no LED is lit (default setting). Almost OFF can be overridden by pressing ^and holding the left half of the DIM/BRIGHT Bar ( ) until the lights turn off. By tapping the Push Pad this setting will automatically be saved and the device will exit Programming Mode A. Note: When Almost OFF Level is set the LED Locator will be illuminated when the dimmer is in the Almost OFF state, even though the light remains on at a reduced energy consumption level.
Program Mode A
To enter Program Mode A: Push and hold the Push Pad and then the right half of the DIM/BRIGHT Bar (^) for 5 seconds until the Locator LED and leftmost LED (LED 1) begin to blink.
Vizia +™ Programming Guide
A-1) Upon releasing the Push Pad and the right half of the DIM/BRIGHT Bar (^) , the Locator LED will continue to blink once per second and the rightmost LED will illuminate to display the device is in Program Mode A-1, Energy Save. To change the Energy Save Level, use the DIM/BRIGHT Bar to move the corresponding LED to the desired discrete preset level according to Chart A. By tapping the Push Pad this setting will automatically be saved and the device will advance to the next programming mode, A-2. CHART A
LED LED 1 LED 2 LED 3 LED 4 LED 5 LED 6 LED 7 (Default) ADVANCED FEATURES SUMMARY MAXIMUM BRIGHTNESS ENERGY SAVINGS 75% 34% savings 80% 29% savings 85% 24% savings 90% 16% savings 95% 8% savings 97% 5% savings 100% (full bright) 0 % Savings
Program Mode B
To enter Program Mode B: Push and hold the ^ Push Pad and then the left half of the DIM/BRIGHT Bar ( ) for 5 seconds until the Locator LED and rightmost LED (LED 7) begin to blink. B-1) Upon releasing the Push Pad, the Locator LED will continue to blink once per second indicating the dimmer is in Program Mode B-1, ON Fade Rate. To change the ON Fade Rate, use the DIM/BRIGHT Bar to move the LED to the desired preset level according to Chart B. By tapping the Push Pad this setting will automatically be saved and the device will advance to the next programming mode, B-2. B-2) The Locator LED will blink 2 times per second to indicate Program Mode B-2, OFF Fade Rate. To change the OFF Fade Rate, use the DIM/BRIGHT Bar to move the LED to the desired preset level according to the Chart B. By tapping the Push Pad this setting will automatically be saved and the device will advance to the next programming mode, B-3. CHART B
LED LED 1 LED 2 (Default) LED 3 LED 4 LED 5 LED 6 LED 7 FADE ON 0 seconds (instant) 0.5 seconds 1.5 seconds 3 seconds 6 seconds 10 seconds 25 seconds FADE OFF 0 seconds (instant) 0.5 seconds 1.5 seconds 3 seconds 6 seconds 10 seconds 25 seconds
A-2) The Locator LED will blink 2 times per second to indicate the device is in Program Mode A-2, Minimum Brightness Level. To change the Minimum Brightness Level from 1-50%, use the DIM/BRIGHT Bar. The light output will reflect the minimum brightness level selected. By tapping the Push Pad this setting will automatically be saved and the device will advance to the next programming mode, A-3.
Leviton Mfg. Co., Inc.
59-25 Little Neck Pkwy, Little Neck, NY 11362-2591 Tech Line: 1-800-824-3005 Fax: 1-800-832-9538 www.leviton.com
© 2008 Leviton Manufacturing Co., Inc. All rights reserved. Subject to change without notice.
B-3) The Locator LED will blink 3 times per second to indicate Program Mode B-3, LED Options. To change the LED Options settings, use the DIM/BRIGHT Bar to move the LED to the desired preset setting according to the chart below. By tapping the Push Pad this setting will automatically be saved and the device will exit Programming Mode B
Program Mode C
To enter Program Mode C: Engage the air-gap switch by gently pressing the top of the Push Pad until the bottom lifts completely out of the frame and a click is heard. All LEDs will extinguish. C) Press Push Pad back into the frame and hold for 7 seconds until and the LED Brightness Display starts bi-directional strobing to indicate Program Mode C, Restore Default. To Restore Default settings, release the Push Pad. This will save defaults settings and exit Programming Mode C.
LED OPTIONS CHART
LED LED 1 LED 2 LED 3 LED 4 LED 5 LED 6 LED 7 LOCATOR LED TIMEOUT Active Active Turns off 5 seconds after use Turns off 5 seconds after use N/A N/A N/A LED BRIGHTNESS DISPLAY OPTIONS Active Turns off 5 seconds after use Active Turns off 5 seconds after use N/A N/A N/A
SWITCH PROGRAMMING
• LED Option - Sets the Locator LED timeout to 5 seconds after use. NOTE: The switch will exit program mode after 3 minutes of inactivity
Program Mode
To enter Program Mode: Push and hold the Push Pad for 10 seconds until the Locator LED begins to blink. Upon releasing the Push Pad, the LED Option will automatically be changed.
LOCATOR LED Default First toggle LOCATOR LED OPTION SETTING Active Turns off 5 seconds after use
Push Pad
VPS15
Locator Light
Leviton Mfg. Co., Inc.
59-25 Little Neck Pkwy, Little Neck, NY 11362-2591 Tech Line: 1-800-824-3005 Fax: 1-800-832-9538 www.leviton.com
© 2008 Leviton Manufacturing Co., Inc. All rights reserved. Subject to change without notice.
Vizia +™ Programming Guide
FAN SPEED CONTROL PROGRAMMING Program Mode A
LED Brightness Display
Fan Speed Bar
To enter Program Mode A: Push and hold the Push Pad and then the right half of the FAN SPEED Bar (^) for 5 seconds until the Locator LED and leftmost LED (LED 1) begin to blink. The Locator LED will blink once per second to indicate Program Mode A, Preset ON Level. To change the current Preset ON Level from HIGH (LED 7), MEDIUM (LED 4) or LOW (LED 1), use the FAN SPEED Bar. If this feature is not desired, ^ press and hold the left half of the FAN SPEED Bar ( ) until no LED is lit (default setting). By tapping the Push Pad this setting will automatically be saved and the device will exit Programming Mode A.
Program Mode B
Push Pad
Vizia +™ Programming Guide
Locator Light
VPF01 • Preset ON Level – Set the turn on fan speed regardless of the previous set level • LED Options – Set the time period in seconds the Locator LED and Fan Speed will stay lit before extinguishing • Restore Defaults – Restores the factory default settings (including device load ON at maximum level)
MODE A B C ADVANCED FEATURES SUMMARY DESCRIPTION RANGE Preset On Level 1% - 100%, not active LED Options Active, turn off after 5s Restore Defaults DEFAULT Not active Active
To enter Program Mode B: Push and hold the Push ^ Pad and then the left half of the FAN SPEED Bar ( ) until the rightmost LED (LED 7) begins to blink. The Locator LED will blink 2 times per second to indicate Program Mode B, LED Options Mode. To change the LED Options settings, use the FAN SPEED Bar to move the LED to the desired preset setting according to the chart below. By tapping the Push Pad this setting will automatically be saved and the device will exit Programming Mode B.
LED LED 1 (Default) LED 3 LED 7 LED LOCATOR TIMEOUT Active Active Turns off 5 seconds after use LED BRIGHTNESS DISPLAY TIMEOUT Active Turns off 5 seconds after use Turns off 5 seconds after use
Program Mode C
To enter Program Mode C: Engage the air-gap switch by gently pressing the top of the Push Pad until the bottom lifts completely out of the frame and a click is heard. All LEDs will extinguish. Press Push Pad back into the frame and hold Push Pad for 7 seconds until the LED Brightness Display starts bi-directional strobing to indicate Program Mode C, Restore Default. Releasing the Push Pad will Restore Default settings and exit programming mode.
Vizia +™ is a trademark of Leviton Manufacturing Co., Inc. Covered by one or more U.S. and Foreign Patents and patents pending.
NOTES: • The device will exit program mode after 3 minutes of inactivity • Pressing the Push Pad at any time during programming will advance the device to the next programming mode.
Leviton Manufacturing Co., Inc.
59-25 Little Neck Parkway, Little Neck, NY 11362-2591 Telephone: 1-800-323-8920 • FAX: 1-800-832-9538 • Tech Line (8:30AM-7:30PM E.S.T. Monday-Friday): 1-800-824-3005
Leviton Manufacturing of Canada, Ltd.
165 Hymus Boulevard, Pointe Claire, Quebec H9R 1E9 • Telephone: 1-800-469-7890 • FAX: 1-800-563-1853
Leviton S. de R.L. de C.V.
Lago Tana 43, Mexico DF, Mexico CP 11290 • Tel. (+52) 55-5082-1040 • FAX: (+52) 5386-1797 • www.leviton.com.mx
Visit our Website at: www.leviton.com
© 2008 Leviton Manufacturing Co., Inc. All rights reserved. Subject to change without notice. G-7904/J7-tp
