Solution

Published on June 2016 | Categories: Documents | Downloads: 32 | Comments: 0 | Views: 289
of 3
Download PDF   Embed   Report

Comments

Content

INTRODUCTION TO
MICROELECTRONIC
FABRICATION SECOND
EDITION
by

RICHARD C. JAEGER

First Printing Errata - Updated 07/30/03

Page number: Correction
42: Problem 2.5 180-nm should be 120-nm.
65: Problems 3.11 and 3.12: Assume a temperature of 1100 oC.
104: Problem 4.4(b) should refer to Fig. 4.12 .
106: Problem 4.10(e) should refer to part (d) .
106: Figure P4.10: The spacings between resistor legs should all be 3
107: Problem 4.14: Assume NB = 1016/cm3 .
107: Problem 4.15: Assume a 0.3 -cm p-type substrate.
107: Problem 4.21(c): the temperature should be 950 oC; Problem 4.21(d) should refer to Fig.
4.12.
128: Problem 5.18: "minimum substrate temperature" should be " maximum substrate
temperature"

150: Problem 6.5: 1000 molecules/cm3 ; Problem 6.14: A1 should be Al
169: The gray shading in Fig. 7.18 is almost invisible. Here is a corrected drawing: Download
Fig. 7.18
171: The figure captions for Fig. 7.20 are reversed.
176: Problem 7.12(c): ... if a 1-m thick "low-K"...
199: Problem 8.4: Compare the five yield ...; Problem 8.5 should refer to Fig. 8.16 not Fig. 8.11.
200: Problem 8.12. Assume a die cost of $1.00 to find the die sizes.
200: Problems 8.13 and 8.15: References to Fig. 8.11 should be to Fig. 8.16.
212: Paragraoh above Section 9.2: "scale factor  = square root of 2"
265: Problem 10.2: NE/DE = should be GE = ...; Problem 10.3: What epitaxial layer doping may
267: Problem 10.13: Reference should be to Table 10.1 not Table 10.2.
268: Problem 10.22: "What is a lower bound ..."; Problem 10.27: 1 m should be 1 m.
270: Table 11.1: Density should be in g/cm3 .
273: Third line: 22o should be 35o.

Answer Corrections
1.5

34.4 x 109 transistors

1.13 1 M, 16 M, 100 M
3.7

3.1 hours, 74 hours

4.3

5.21 hrs

4.15 14.5, 34.9, 203, 2840, 9.72, 12.5
5.1

3.5 x 1018/cm3, 7.5 x 1013/cm2 , 0.47 m

5.3

900 keV, 0.13 m

5.5

1.0 x 1015/cm2, 10.5 hrs

5.7

60.7 sec

5.11 2.69 x 104 m/sec should be 8.85 x104 m/sec
5.13 53 nm, 870 nm
6.1

820 psec

6.3

2.68 x 1020 molecules/sec, 72 m, 7.5 x 10-7 Torr

6.11 1247oC, delete 0.35 eV
6.15 0.886, 0.886, 0.769
6.17 N(x) = 1020{1 + erf [(x-2)/0.045]} /cm3
7.5

5 x 10-9-cm2

8.3

392, 492, 3746

8.7

$4.06 vs. $4.89, $6.52 vs. $6.57

8.13 17%, 8.3%
9.13 -0.16 V, -1.21 V, 1.67 x 1012/cm2, 3.02 x 1011 /cm2
9.21 384 2, 40  2
10.3 90 V
10.9 2/3, 2 , 2d(W+L)/WL ...
10.13 193 k, 9.63 k, 803 
10.19 33 nm
10.27 6-7 V, 8 V

Sponsor Documents

Or use your account on DocShare.tips

Hide

Forgot your password?

Or register your new account on DocShare.tips

Hide

Lost your password? Please enter your email address. You will receive a link to create a new password.

Back to log-in

Close