Tube
Content
Summary of Policy No.: 555776202
Life Insured
Plan Name
Policy Issue date
Payment Mode
Due Date
Client I.D
:
Mr. Sidhartha Sankar Sadangi
:
Max Life Life Gain Premier
:
:
26-FEB-2014
Annual
:
26-FEB-2015
:
5002965371
This post "Fluorescent Light Wiring Diagram | Tube Light Circuit" is about
how to wiring fluorescent light and "how a Fluorescent Tube Light works".
The wiring process of fluorescent tube lamp/light with Ballast,Starter is quite
easy and simple. In most cases when we buy a fluorescent light it comes in
a complete set with all wire connected. If you want do it yourself (DIY), you
can buy all the parts individually. And you can complete all connection of the
fluorescent light/lamp with the help of this wiring circuit diagram.
Fluorescent Light Wiring Diagram
Fig: Fluorescent Light Wiring Diagram
Main parts of Fluorescent Tube Light:
1.Fluorescent Tube
2.Ballast
3.Starter
4.Holder, wire etc.
How Fluorescent Light's works:
The starter is like a key of fluorescent light because it is used to light up the
tube. When we connect the AC supply voltage to the circuit, then the starter
act like short circuited and current flow through those filament (located at
the first and second end of the tube light) and the filament generate heat
and it ionized the gas (mercury vapor) in the fluorescent tube lamp. So the
gas becomes electrically conductive medium. At the same time when the
starter opened the circuit path of two filaments from series connected, then
the ballast release its stored voltage. And it makes the fluorescent tube fully
lighten. Now the starter has no job in the circuit, if you open it from the
circuit the fluorescent tube light will be still lighten, until you release the
main supply.
Re-using fused tube-light by 4 diode
A tube-light get fused due to use from a long time. You may notice that a used fluorescent
tube-light get black colored on the both end of it. This circuit is to light-up those fused tubelight.
Have you think about re using a fused tube light? (Which is usually thrown out). Well here
I’m showing a simple circuit using 4 diode for re-using a fused tube light.
The circuit diagram shown above is quite simplified from basic tube light wiring diagram by
adding a bridge rectifier. Bridge rectifier provides high voltage DC to the both end of tube.
All we have focused in this project is to lighting-up the weak tube using high voltage DC.
Note: A fully damaged or broken tube-light could not be light-up anyway. Use those tubelight for this project that is still trying to light-up but not fully lightened on the basic
connection of tube-light.
Life Insured
Plan Name
Policy Issue date
Payment Mode
Due Date
Client I.D
:
Mr. Sidhartha Sankar Sadangi
:
Max Life Life Gain Premier
:
:
26-FEB-2014
Annual
:
26-FEB-2015
:
5002965371
This post "Fluorescent Light Wiring Diagram | Tube Light Circuit" is about
how to wiring fluorescent light and "how a Fluorescent Tube Light works".
The wiring process of fluorescent tube lamp/light with Ballast,Starter is quite
easy and simple. In most cases when we buy a fluorescent light it comes in
a complete set with all wire connected. If you want do it yourself (DIY), you
can buy all the parts individually. And you can complete all connection of the
fluorescent light/lamp with the help of this wiring circuit diagram.
Fluorescent Light Wiring Diagram
Fig: Fluorescent Light Wiring Diagram
Main parts of Fluorescent Tube Light:
1.Fluorescent Tube
2.Ballast
3.Starter
4.Holder, wire etc.
How Fluorescent Light's works:
The starter is like a key of fluorescent light because it is used to light up the
tube. When we connect the AC supply voltage to the circuit, then the starter
act like short circuited and current flow through those filament (located at
the first and second end of the tube light) and the filament generate heat
and it ionized the gas (mercury vapor) in the fluorescent tube lamp. So the
gas becomes electrically conductive medium. At the same time when the
starter opened the circuit path of two filaments from series connected, then
the ballast release its stored voltage. And it makes the fluorescent tube fully
lighten. Now the starter has no job in the circuit, if you open it from the
circuit the fluorescent tube light will be still lighten, until you release the
main supply.
Re-using fused tube-light by 4 diode
A tube-light get fused due to use from a long time. You may notice that a used fluorescent
tube-light get black colored on the both end of it. This circuit is to light-up those fused tubelight.
Have you think about re using a fused tube light? (Which is usually thrown out). Well here
I’m showing a simple circuit using 4 diode for re-using a fused tube light.
The circuit diagram shown above is quite simplified from basic tube light wiring diagram by
adding a bridge rectifier. Bridge rectifier provides high voltage DC to the both end of tube.
All we have focused in this project is to lighting-up the weak tube using high voltage DC.
Note: A fully damaged or broken tube-light could not be light-up anyway. Use those tubelight for this project that is still trying to light-up but not fully lightened on the basic
connection of tube-light.
