Wood
Content
Materials for Civil and Construction Engineers CHAPTER 10 Wood
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
Introduction
Wood is the earliest construction material used by mankind. easy to use durable high strength low weight widely available low cost Still very widely used today for: building frames bridges utility poles floors roofs trusses piles, etc.
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
2
Classification of Trees
Endogenous (intertwined growth): e.g., palm trees very strong and lightweight not generally used for engineering applications in U.S. Exogenous (outward growth): e.g., most other trees Fibers grow from the center outward by adding concentric layers (annual rings) which gives more predictable engineering properties. Deciduous (broad leaf) = hardwood (ash, oak, maple, walnut, etc.) ± expensive slow growing Coniferous (cone bearing, evergreens) = softwood (Douglas fir, pine, spruce, cedar, etc.)
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
3
10.1 Structure of Wood
Each annual ring of exogenous tree is composed of: Earlywood (light ring): rapid spring growth of hollow thin-walled cells Latewood (dark ring): dense summer growth of thickwalled cells which are much harder & stronger
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
4
Main Structural Features of Tree Stem
From center axis outwards:
Pith ± center stem Heartwood (darker) ± provides structural support Sapwood (lighter) ± transports the sap Cambium (very thin layer) ± location of wood growth Inner bark Outer bark
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
5
Wood is Anisotropic ±
Longitudinal
properties change with direction:
parallel to the long axis (grain) strongest and least shrinkage
Radial
perpendicular to the growth rings (out from center)
Tangential
tangent to the growth rings weakest and most shrinkage
directions influence strength, modulus, thermal expansion, conductivity, shrinkage, etc.
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
6
10.2 Chemical Composition
Cellulose 50% by weight polymer that forms strands (fibrils) that make up cell walls (wood fibers) Gcellulose = 1.5 High density indicates higher strength Lignin 23-33% of softwood 16-25% of hardwood by weight glue Hemicellulose 15-20% of softwood 20-30% of hardwood Extractives 5-30% by weight tannins, coloring matters, essential oils, fats, resins, waxes, starches Ash-forming (minerals) 0.1-3% by weight calcium, potassium, phosphate, silica
7
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
Wm Wd Mc ! 100 10.3 Moisture Content Wd
shrinkage, strength, & weight depend on moisture content depends on air temperature and humidity: slow changing so it tends to adjust near the average Equilibrium Moisture Content (EMC) moisture content for average atmospheric conditions 1% when hot & dry >130oF & 5% humidity 20% when warm & humid <80oF & 90% humidity
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
8
Fiber Saturation Point (FSP)
moisture content when cells are completely saturated with bound water but no free water inside cell cavities
water inside cell cavities doesn't affect shrinkage held tightly in cell cavities, wood shrinks on removal
FSP = 21-32% Above FSP changes affect only wet weight Below FSP small changes strongly affect all physical and mechanical properties
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
9
Fiber Saturation Point
Shrinkage
largest shrinkage is in the tangential direction smallest shrinkage is in the longitudinal direction zero shrinkage above FSP regardless of direction For glulam (varying growth ring orientations) assume 6% shrinkage in 30% change in m/c below
FSP (or 1% shrinkage per 5% change in m/c)
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
10
10.4 Wood Production
Production Steps: 1. Harvesting 2. Sawing 3. Seasoning (drying) 4. Surfacing (Planing) (optional) 5. Grading 6. Preservative Treating (optional)
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
11
Wood Products for Construction
Dimensional lumber ± 2´ to 5" thick ± 2x4,s etc. used for light framing ± studs, joists, beams, rafters, trusses, decking Heavy timber ± 4x6, 6x6, 8x8 and larger usually rough sawn (actual sizes) used for heavy framing, railroad ties, landscaping Round stock posts and poles ± used for marine piling, utility poles, etc. Specialty items handrails, spindles, radius edge decking, turned posts, lattice, etc. Engineered wood products bonding wood strands, veneers, lumber or other wood fibers large integral composite unit
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
12
Mamlouk/Zaniewski, Materials for Civil and Chapter 10: Wood Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
Step 1. Harvesting
minimal sap concerns of fire hazard other plant growth and underbrush is minimal
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
14
Step 2. Sawing
Live (plain) sawing ± most rapid and economic Quarter sawing ± maximum amount of prime (vertical) cuts Combination ± most typical
Live (Plain) Sawing
Quarter Sawing
Combination
15
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
Three types of board cut Flat-sawn (grain is <45o from flat side) worst quality, most problems and defects Rift-sawn (45o-80o) Quarter-sawn (vertical- or edge-sawn) (80o-90o) best quality, least shrinkage problems
Flat-Sawn
Rift-Sawn
Quarter-Sawn
16
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
Step 3. Seasoning (Drying)
Green wood has 30-200% moisture content ~15% when it leaves the mill Methods of Seasoning air drying (cheap & slow) kiln drying (fast & expensive) usually a combination Uneven shrinkage in different directions during seasoning causes warping, checks, shakes, etc. Type of cut controls these problems (vertical is the best)
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
17
Step 4. Surfacing (Planing) (Planing)
Surfacing takes 1/4" (or more) from each side S4S = surfaced 4 sides = ³dressed´ Nominal sizes refer to the rough-sawn (unsurfaced) dimensions of the lumber in inches For example, the actual dimensions of a 2 x 4 are 1 ½ in. x 3 ½ in.
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
18
10.5 Lumber Grades (Step 5)
Several agencies for different regions and species Graded according to number of defects that affect strength & durability (knots, checks, pitch pockets, shakes, stains) Visual (appearance) grading Stress (structural) grading ± Table 10.3 Hardwood grades ± visual (also stress) grading Softwood grades ± visual & machine stress grading For civil engineering applications, appearance grades are less important than structural grades
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
19
10.6 Lumber Defects
Affect both appearance & mechanical properties Caused by: natural wood growth seasoning too fast wood diseases animal parasites faulty processing Knots ± branch base that degrades mechanical properties sound, tight knots may be good in compression but don¶t count on it
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
20
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
21
Shakes ± wood separations between annual rings Wane ± bark or other soft wood left on the edge of the board Sap Streak ± colored streak of sap accumulated in wood fibers Reaction Wood ± extra dense woody tissue that can cause warping and cracking Pitch pockets ± opening between annual rings that contain resin Bark Pockets ± small patches of bark embedded in the wood Checks ± ruptures along the grain from drying
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
22
Splits ± lengthwise separations caused by mishandling or seasoning Warping ± (several types) from uneven drying of internal tree stress Bowing ± lengthwise curvature from end to end Crooking ± lengthwise curvature from side to side Cupping ± edges roll up Twisting ± one corner lifts Raised, Loosened, or Fuzzy Grain Chipped or Torn Grain Machine Burn ± from worn saw blades
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
23
10.7 Physical Properties of Wood
1. Specific Gravity & Density Specific gravity of the cell walls (cellulose) = 1.5 regardless of species excellent indicator of the amount of material (and properties) in dry wood closer to 1.5 means more cell walls which is denser & stronger Dry density = usually 20-45 lb/ft3 (300-700 kg/m3)
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
24
2. Thermal Properties Thermal conductivity The rate that heat flows through (inverse of thermal resistance R value) Good R value (R = 1 / conductivity) much better than metals slightly worse than insulation reduces loss of heat and cold delays fire Specific Heat Ratio of the quantity of heat required to raise the temp. of the material 1o to that required to raise the temp. of an equal mass of water 1o
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
25
Thermal Diffusivity Rate that material absorbs heat from surroundings Much better (lower) than most other building materials Thermal Expansion Anisotropic: 5-10x greater across grain than parallel to it Applying heat to wood: first expands the wood from thermal expansion then it shrinks from moisture loss (when below FSP) 3. Electrical Properties Good electrical insulator which decreases with moisture content ± more water is a better electrical conductor
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
26
Wood is extremely anisotropic 1. Modulus of Elasticity 1-2 x 106 psi ± for compression parallel to the grain linear up to proportional limit, then small non-linear curve Depends on: species variation moisture content specific gravity direction of grain
10.8 Mechanical Properties of Wood
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
27
2. Strength Properties Vary widely because of anisotropy, moisture content, defects, etc. Tensile strength is greater than compressive strength Tensile strength parallel to grain is 20x greater than perpendicular
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
28
3. Load Duration Wood can support higher loads of short duration than sustained loads Under sustained loads wood continues to deform Design values assume 10 year loading and/or 90% of full maximum load throughout life of the structure Multiply design values by load duration factors for shortduration loads
Load Duration Factors
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
29
4. Damping Capacity Vibration damping (like shock absorbers) increases with moisture content up to FSP 10x greater damping than structural metals wood structures dampen vibrations much better than metal
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
30
strength of wood structures is usually controlled by the joints and connections, which is the main concern of structural wood design classes we have lots of experience with smaller structures (residential, light commercial) so design is usually empirical
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
31
10.9 Mechanical Testing
Wood is tested to predict performance two main techniques
testing of timbers of structural sizes (ASTM D 198)
testing of representative, small, clear specimens (ASTM D 143)
Testing of structural-size members is more important ± more applicable to design values Tests include flexure, compression, tension, etc. Flexure test is more commonly used than the other tests Two-point, third-point, or center-point loading
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
32
ThirdThird-point bending test on a 4 x 6 wood lumber
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
33
Testing Representative, Small, Clear Specimens
Compression parallel to grain Hardness perpendicular to grain
Tension perpendicular to grain
Compression perpendicular to grain
Tension parallel to grain
Hardness parallel to grain
Bending
34
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
10.10 Design Considerations
For design of wood structures, strength properties (Tables 10.3 &10.4) must be adjusted for the following factors Load duration Temperature Size Flat use Column stability Wet service Beam stability Volume (glulam only) Curvature (glulam only) Bearing area
Repetitive member (lumber only)
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
35
10.11 Organisms that Degrade Wood
Fungi caused dry rot Spruce Ips Beetle Marine-borer damage to a buried pile
Bacteria damage black heartwood Termite damage
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
36
10.12 Wood Preservation
1. Petroleum-based Solutions 2. Waterborne Preservatives (Salts) Application Techniques Superficial treatment: generally not effective Liquid penetration (pressure treating at high temp., heat, & moisture) Structural members need to be fabricated as much as possible before treatment in order not to expose untreated wood by cutting, drilling holes, etc. If not possible, treat cuts and holes with a liberal application of field applied preservative
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
Chapter 10: Wood
37
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
38
10.13 Engineered Wood Products
Made by bonding together wood strands, veneers, lumber, or other forms of wood fibers to produce large units engineered to produce specific and consistent mechanical properties that are better than natural large pieces very difficult and expensive to find high quality large natural pieces
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
39
Plywood thin sheets (plies) glued together with the grain at right angles to each other so it has the same properties in both directions veneer is peeled from a soaked log on a giant lathe
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
40
Particle & strand board
glue together wood scraps with resin to form sheets: particle board = sawdust sized particles chip board = randomly oriented wood chips OSB = wood chips & strands oriented in specific direction
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
41
Floor joists made with two 2x4s or 2x6s as flanges and an OSB web
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
42
Glue-Laminated Timbers (Glulam)
lumber glued together with the parallel grain used for structural members, furniture, sports equipment, and decorative wood finishes preferred because:
ease of manufacturing large members from standard commercial lumber can vary the cross section along the length special architectural designs can use lower wood grade in less stressed areas minimizes shrinkage defects
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
43
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
Introduction
Wood is the earliest construction material used by mankind. easy to use durable high strength low weight widely available low cost Still very widely used today for: building frames bridges utility poles floors roofs trusses piles, etc.
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
2
Classification of Trees
Endogenous (intertwined growth): e.g., palm trees very strong and lightweight not generally used for engineering applications in U.S. Exogenous (outward growth): e.g., most other trees Fibers grow from the center outward by adding concentric layers (annual rings) which gives more predictable engineering properties. Deciduous (broad leaf) = hardwood (ash, oak, maple, walnut, etc.) ± expensive slow growing Coniferous (cone bearing, evergreens) = softwood (Douglas fir, pine, spruce, cedar, etc.)
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
3
10.1 Structure of Wood
Each annual ring of exogenous tree is composed of: Earlywood (light ring): rapid spring growth of hollow thin-walled cells Latewood (dark ring): dense summer growth of thickwalled cells which are much harder & stronger
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
4
Main Structural Features of Tree Stem
From center axis outwards:
Pith ± center stem Heartwood (darker) ± provides structural support Sapwood (lighter) ± transports the sap Cambium (very thin layer) ± location of wood growth Inner bark Outer bark
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
5
Wood is Anisotropic ±
Longitudinal
properties change with direction:
parallel to the long axis (grain) strongest and least shrinkage
Radial
perpendicular to the growth rings (out from center)
Tangential
tangent to the growth rings weakest and most shrinkage
directions influence strength, modulus, thermal expansion, conductivity, shrinkage, etc.
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
6
10.2 Chemical Composition
Cellulose 50% by weight polymer that forms strands (fibrils) that make up cell walls (wood fibers) Gcellulose = 1.5 High density indicates higher strength Lignin 23-33% of softwood 16-25% of hardwood by weight glue Hemicellulose 15-20% of softwood 20-30% of hardwood Extractives 5-30% by weight tannins, coloring matters, essential oils, fats, resins, waxes, starches Ash-forming (minerals) 0.1-3% by weight calcium, potassium, phosphate, silica
7
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
Wm Wd Mc ! 100 10.3 Moisture Content Wd
shrinkage, strength, & weight depend on moisture content depends on air temperature and humidity: slow changing so it tends to adjust near the average Equilibrium Moisture Content (EMC) moisture content for average atmospheric conditions 1% when hot & dry >130oF & 5% humidity 20% when warm & humid <80oF & 90% humidity
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
8
Fiber Saturation Point (FSP)
moisture content when cells are completely saturated with bound water but no free water inside cell cavities
water inside cell cavities doesn't affect shrinkage held tightly in cell cavities, wood shrinks on removal
FSP = 21-32% Above FSP changes affect only wet weight Below FSP small changes strongly affect all physical and mechanical properties
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
9
Fiber Saturation Point
Shrinkage
largest shrinkage is in the tangential direction smallest shrinkage is in the longitudinal direction zero shrinkage above FSP regardless of direction For glulam (varying growth ring orientations) assume 6% shrinkage in 30% change in m/c below
FSP (or 1% shrinkage per 5% change in m/c)
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
10
10.4 Wood Production
Production Steps: 1. Harvesting 2. Sawing 3. Seasoning (drying) 4. Surfacing (Planing) (optional) 5. Grading 6. Preservative Treating (optional)
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
11
Wood Products for Construction
Dimensional lumber ± 2´ to 5" thick ± 2x4,s etc. used for light framing ± studs, joists, beams, rafters, trusses, decking Heavy timber ± 4x6, 6x6, 8x8 and larger usually rough sawn (actual sizes) used for heavy framing, railroad ties, landscaping Round stock posts and poles ± used for marine piling, utility poles, etc. Specialty items handrails, spindles, radius edge decking, turned posts, lattice, etc. Engineered wood products bonding wood strands, veneers, lumber or other wood fibers large integral composite unit
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
12
Mamlouk/Zaniewski, Materials for Civil and Chapter 10: Wood Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
Step 1. Harvesting
minimal sap concerns of fire hazard other plant growth and underbrush is minimal
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
14
Step 2. Sawing
Live (plain) sawing ± most rapid and economic Quarter sawing ± maximum amount of prime (vertical) cuts Combination ± most typical
Live (Plain) Sawing
Quarter Sawing
Combination
15
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
Three types of board cut Flat-sawn (grain is <45o from flat side) worst quality, most problems and defects Rift-sawn (45o-80o) Quarter-sawn (vertical- or edge-sawn) (80o-90o) best quality, least shrinkage problems
Flat-Sawn
Rift-Sawn
Quarter-Sawn
16
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
Step 3. Seasoning (Drying)
Green wood has 30-200% moisture content ~15% when it leaves the mill Methods of Seasoning air drying (cheap & slow) kiln drying (fast & expensive) usually a combination Uneven shrinkage in different directions during seasoning causes warping, checks, shakes, etc. Type of cut controls these problems (vertical is the best)
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
17
Step 4. Surfacing (Planing) (Planing)
Surfacing takes 1/4" (or more) from each side S4S = surfaced 4 sides = ³dressed´ Nominal sizes refer to the rough-sawn (unsurfaced) dimensions of the lumber in inches For example, the actual dimensions of a 2 x 4 are 1 ½ in. x 3 ½ in.
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
18
10.5 Lumber Grades (Step 5)
Several agencies for different regions and species Graded according to number of defects that affect strength & durability (knots, checks, pitch pockets, shakes, stains) Visual (appearance) grading Stress (structural) grading ± Table 10.3 Hardwood grades ± visual (also stress) grading Softwood grades ± visual & machine stress grading For civil engineering applications, appearance grades are less important than structural grades
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
19
10.6 Lumber Defects
Affect both appearance & mechanical properties Caused by: natural wood growth seasoning too fast wood diseases animal parasites faulty processing Knots ± branch base that degrades mechanical properties sound, tight knots may be good in compression but don¶t count on it
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
20
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
21
Shakes ± wood separations between annual rings Wane ± bark or other soft wood left on the edge of the board Sap Streak ± colored streak of sap accumulated in wood fibers Reaction Wood ± extra dense woody tissue that can cause warping and cracking Pitch pockets ± opening between annual rings that contain resin Bark Pockets ± small patches of bark embedded in the wood Checks ± ruptures along the grain from drying
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
22
Splits ± lengthwise separations caused by mishandling or seasoning Warping ± (several types) from uneven drying of internal tree stress Bowing ± lengthwise curvature from end to end Crooking ± lengthwise curvature from side to side Cupping ± edges roll up Twisting ± one corner lifts Raised, Loosened, or Fuzzy Grain Chipped or Torn Grain Machine Burn ± from worn saw blades
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
23
10.7 Physical Properties of Wood
1. Specific Gravity & Density Specific gravity of the cell walls (cellulose) = 1.5 regardless of species excellent indicator of the amount of material (and properties) in dry wood closer to 1.5 means more cell walls which is denser & stronger Dry density = usually 20-45 lb/ft3 (300-700 kg/m3)
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
24
2. Thermal Properties Thermal conductivity The rate that heat flows through (inverse of thermal resistance R value) Good R value (R = 1 / conductivity) much better than metals slightly worse than insulation reduces loss of heat and cold delays fire Specific Heat Ratio of the quantity of heat required to raise the temp. of the material 1o to that required to raise the temp. of an equal mass of water 1o
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
25
Thermal Diffusivity Rate that material absorbs heat from surroundings Much better (lower) than most other building materials Thermal Expansion Anisotropic: 5-10x greater across grain than parallel to it Applying heat to wood: first expands the wood from thermal expansion then it shrinks from moisture loss (when below FSP) 3. Electrical Properties Good electrical insulator which decreases with moisture content ± more water is a better electrical conductor
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
26
Wood is extremely anisotropic 1. Modulus of Elasticity 1-2 x 106 psi ± for compression parallel to the grain linear up to proportional limit, then small non-linear curve Depends on: species variation moisture content specific gravity direction of grain
10.8 Mechanical Properties of Wood
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
27
2. Strength Properties Vary widely because of anisotropy, moisture content, defects, etc. Tensile strength is greater than compressive strength Tensile strength parallel to grain is 20x greater than perpendicular
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
28
3. Load Duration Wood can support higher loads of short duration than sustained loads Under sustained loads wood continues to deform Design values assume 10 year loading and/or 90% of full maximum load throughout life of the structure Multiply design values by load duration factors for shortduration loads
Load Duration Factors
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
29
4. Damping Capacity Vibration damping (like shock absorbers) increases with moisture content up to FSP 10x greater damping than structural metals wood structures dampen vibrations much better than metal
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
30
strength of wood structures is usually controlled by the joints and connections, which is the main concern of structural wood design classes we have lots of experience with smaller structures (residential, light commercial) so design is usually empirical
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
31
10.9 Mechanical Testing
Wood is tested to predict performance two main techniques
testing of timbers of structural sizes (ASTM D 198)
testing of representative, small, clear specimens (ASTM D 143)
Testing of structural-size members is more important ± more applicable to design values Tests include flexure, compression, tension, etc. Flexure test is more commonly used than the other tests Two-point, third-point, or center-point loading
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
32
ThirdThird-point bending test on a 4 x 6 wood lumber
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
33
Testing Representative, Small, Clear Specimens
Compression parallel to grain Hardness perpendicular to grain
Tension perpendicular to grain
Compression perpendicular to grain
Tension parallel to grain
Hardness parallel to grain
Bending
34
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
10.10 Design Considerations
For design of wood structures, strength properties (Tables 10.3 &10.4) must be adjusted for the following factors Load duration Temperature Size Flat use Column stability Wet service Beam stability Volume (glulam only) Curvature (glulam only) Bearing area
Repetitive member (lumber only)
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
35
10.11 Organisms that Degrade Wood
Fungi caused dry rot Spruce Ips Beetle Marine-borer damage to a buried pile
Bacteria damage black heartwood Termite damage
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
36
10.12 Wood Preservation
1. Petroleum-based Solutions 2. Waterborne Preservatives (Salts) Application Techniques Superficial treatment: generally not effective Liquid penetration (pressure treating at high temp., heat, & moisture) Structural members need to be fabricated as much as possible before treatment in order not to expose untreated wood by cutting, drilling holes, etc. If not possible, treat cuts and holes with a liberal application of field applied preservative
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
Chapter 10: Wood
37
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
38
10.13 Engineered Wood Products
Made by bonding together wood strands, veneers, lumber, or other forms of wood fibers to produce large units engineered to produce specific and consistent mechanical properties that are better than natural large pieces very difficult and expensive to find high quality large natural pieces
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
39
Plywood thin sheets (plies) glued together with the grain at right angles to each other so it has the same properties in both directions veneer is peeled from a soaked log on a giant lathe
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
40
Particle & strand board
glue together wood scraps with resin to form sheets: particle board = sawdust sized particles chip board = randomly oriented wood chips OSB = wood chips & strands oriented in specific direction
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
41
Floor joists made with two 2x4s or 2x6s as flanges and an OSB web
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
42
Glue-Laminated Timbers (Glulam)
lumber glued together with the parallel grain used for structural members, furniture, sports equipment, and decorative wood finishes preferred because:
ease of manufacturing large members from standard commercial lumber can vary the cross section along the length special architectural designs can use lower wood grade in less stressed areas minimizes shrinkage defects
Mamlouk/Zaniewski, Materials for Civil and Construction Engineers, Third Edition. Copyright © 2011 Pearson Education, Inc.
43
