Best Practices in Weaving

Published on March 2017 | Categories: Documents | Downloads: 38 | Comments: 0 | Views: 423
of 12
Download PDF   Embed   Report

Comments

Content

 

Best Practices in Weaving To meet the ever-growing demands of quality and quantity of the textile industry, the world of weaving has witnessed tremendous technological advancement during the past three decades. The innovations were not confined to final f inal stage of fabric forming but also at various stages of weaving and weaving preparatory. The fabric forming technology has taken a big leap from handloom weaving of primitive years to power loom atomize weaving to today‟s high-speed shuttle less weaving technology. It is the result of persistent efforts put in by the scientists and technologists over the years. These sophisticated weaving technologies are considered as basic tool to ensure high productivity and quality in fabric. The mere existence of sophisticated weaving technology alone will not ensure fulfillment of above goals and thus it is needless to say to handle such sophisticated weaving technologies, also need best work  practices by the people handling these technologies, to ensure efficient weaving operations. It will not be out of the place to discuss the process flow of weaving and then the best practices to be followed at each stage of fabric manufacturing. A systematic process flow diagram will help to understand weaving in a better way. Yarn from Spinning Yarn Dyeing Winding

Direct Warping

Sectional Warping

Warping

Sizing

Drawing in / Knotting

Weaving

Fabric Inspection

 

Best Practices in Yarn Go down

Weaving process converts yarn in to fabric therefore the yarn is considered as raw material for weaving. Yarn is supplied to the weaving mill by Yarn supplier or spinning mill directly in the form of cones, which is stored in Yarn Go down. In Yarn go down following practices must be carried out for smooth functioning.

  All cones should be packed in polythene bags before transported to next process.



  Proper stacking of yarn, received from different suppliers to avoid lot to lot and



package to package variation for further process i.e. Dyeing D yeing and Weaving.

  Provide protection to the yarn, against external damages like bad handling, sunlight



and rain.

  Easy availability of yarn at one place for easy handling and to reduce machine down



time of further process.

  Make proper record of yarn received from supplier, Issued against requirement and



received return from Winding, Warping, Dyeing and Weaving department.

  Identify the trend of consumption of yarn separately for better inventory.



  Control on yarn wastages.



Best Practices in Winding Process

Winding converts, yarns from smaller spinner‟s bobbins to big cones in the form of soft and hard. Spinner‟s bobbin contains 60  –  80 Gms of yarn (3,000  –  5,000 mtrs) which are converted in to larger yarn package known as cone containing approx.

1.25 to 1.5 Kg of yarn

(1,00,000 -1,25,000 mtrs). Soft cones are used for „yarn dyeing purpose‟ where as hard cones are used as „weft for weaving‟ and as „cones „ cones for direct warping‟. Soft cones after dyeing are further warping‟.

 

converted in to as „big cones for dyed weft weft‟‟ or „small cones (Length of cones depends up on the fabric order length) for sectional warping warping‟‟. Winding process also removes objectionable yarn faults from yarn during winding. In winding process following practices must be carried out for smooth functioning of further process like warping and weaving.

  At 6% moisture content cotton shows high strength



therefore it is very much essential to condition the yarn before further process.

  Yarn received from dyed yarn ware-house for warp



winding must have right information on it like production order no., issued quantity, Count, Shade no., Lot no. etc.

  Before warp winding must check for package



condition, shade variation in packages, Bronziness problem etc. to avoid fabric defects which are observed only after weaving.

  Yarn must wound on clean empty cones specified for that particular count.



  Inner layer (Bottom) of dyed package yarn must remove during winding to avoid yarn



dyeing defect in fabric like undyed & uneven dyeing. In normal practice for lighter shade 10-15gms and for dark shade 20-25gms of yarn are removed from each dyed packages. 

  Never mix different lots even it is same in shade. Use of identification sticker will help.

  Use of different size of dyed yarn packages is



advisable to avoid shade variation problem in weft chambray fabric.

  Always use Knotter for mending broken end.



Winding

  Frequent checking of splicing quality and strength of knot for at least 10% of drums/ 



day will ensure better machine condition.

  Frequent checks for yarn passage of each spindle, yarn tension, tension unit disc



position, and removal of fluff and wild yarn helps for better winding quality.

 

  Preset all machine settings to remove all the objectionable faults and check frequently



to ensure zero deviation.

  Ensure Good housekeeping and PEEP Management system. (Place for Everything and



Everything in Place)

  Less attending time to start stopped drums, improves productivity.



  Use of nose mask avoids inhaling of fly and fluff.



Best Practices in Warping Process The initial stage in producing woven fabric is to convert yarn from cones to warp beams. Warping provides even and parallel distribution of warp ends over the entire width of the warping beam. Direct warping and Sectional warping are two types of warping and widely used in industry. When several beams with same beam length are prepared and then all beams are unwound on the weavers beam is called as direct warping. This type of warping is more productive and commonly used for bulk production. Similarly when several sections are wound in a sequence which is parallel to each other on a drum and then all sections are unwound on the weavers beam is called as sectional warping. This type of warping is cost effective for short and striped warp and fancy pattern fabric. In warping following practices must carry out for smooth functioning in weaving.

  Cleaning of machine at every creel



change will improve productivity of warping machine.

Direct Warping

  Polishing of weavers beam flanges to avoid scratches on it helps to reduce warp



brakes.

  Even tension throughout the warp sheet will ensure good quality of warping.



  Broken ends should mend correctly i.e. first find out the missing ends in the drum by



reversing 2 to 3 turns and then mend it.

  Never use two different yarn lots in same creel.



 

  Ensure even creel tension or warping speed in between one set.



  For beam dyeing beam density should maintain at 360 to 400gms/ltr.



  Creeling of cones must be done and



checked thoroughly as per as per the pattern given in design sheet.

  Do not use damaged cones, it will cause



frequent breakages of warp yarn and minimize the productivity.

  First pattern always starts from right side



Sectional Warping

of the creel.

  Adjust the section width and section starting position for every section start-up to



avoid section mark in the fabric.

  Use of seven leases and cross lease during each section winding improves working in



sizing and weaving.

Best Practices in Sizing Process

Strong, smooth and elastic yarn is the prime requirement of weaving process. To achieve these properties without deteriorating the inherent quality of yarn a starch /polymeric film or coating is applied on the warp yarn. During application of size it get penetrated in to the yarn structure and enhances its breaking load capacity, softeners makes surface smoother and binders binds protruding fibers of yarn resulting improvement in the warp yarn strength, smoother yarn surface aand nd reduction in hairiness of yarn. In Sizing following practices must carry out for smooth functioning in weaving.

  Frequent



check

and

maintain

viscosity and RF value of the size recipe.

  Close monitoring on temperature of cylinders and size-box at every stage of sizing.



 

  Close monitoring on machine parameters like squeezing pressures, dividing zone and



drag roll tension etc.

  While inserting lease rods start the machine in slow speed and ensure comb assembly



is lowered while knots are passing.

  Do the denting in the comb by using



cross lease, starting from the centre of comb.

  Apply the press roller after 20-25



mtrs, then run the machine at normal speed i.e. 40 mtrs /min.

  Maintain sheet opening angle equal to lease rod dia. and stretch always maintain below



1%.

  Ensure sized beam moisture content in between 5%  –  6 % because less moisture in



sized yarn makes it brittle and more moisture makes it sticky. Drain used size recipe from saw box and clean saw box properly, if light color set is   running after dark color set.

  Don't reuse the old or used size recipe.



  Don't allow un-dried portion to go inside the sized beam.



  Don‟t apply high stretch on warp sheet, will result in elongation loss of yarn and cause



high warp brakes in weaving.

  Don‟t size single count and double count together, double count will get loosen and



created crossing and migration in sizing and warp w arp brake at weaving.

  Use even warp tension across the width of the beam.



Best Practices in Drawing- in Process

After sizing, sized weaver beams are sent to drawing in department to draw each warp ends in predetermined drawing sequence provided by the design department. Design sheet provides information which is required for drawing in like Draft, Denting Plan and Warp Pattern. In drawing in each ends are threaded through a drop pin, heald eye and the reed according to the plan. After completion of drawing in process drawn d rawn set goes to weaving and gaited on loom.

 

  For better performance in weaving and quick startup of loom a drawn set must have almost zero broken ends and crossing ends. Broken ends and crossing ends need more time to mend and correct it thus in most of the case it is the only reason for higher beam gaiting time resulting less productivity of loom. 

In Drawing- in following practices must carry out for smooth functioning in weaving.

  Warp sheet should properly brush and combed



at

the

preparation

stage,

to

ensure

parallelization parallelizati on of each yarn before clamping.

  Drop pins, serrated bars, healdwires, healdframes and reeds must be clean thoroughly



before drawing in.   Strict checking and immediate disposal of damaged drop pins, serrated bars, healdwires, healdframes and reeds are required to improve weaving efficiency.

  Application of lamination sheet in drawn set reduces gaiting time considerably and



also ensures less end breakages during gaiting process.

  A good understanding of Draft, Denting Plan



and Design is very much needed to avoid any drawing in mistakes thus periodic training to the operators is must.

  Before handing over to weaving, a drawn set must be checked properly. Preparation of 



checklist and rigorous follow-up will help in this.

Best Practices in Textile Designing Textile designing involves producing patterns for cloth used in clothing, household textiles such as towel, upholstery and decorative textiles such as curtains / carpets. The field encompasses the actual pattern making as well as supervising part or all of the production process. Combination of colours and weaves play major role in textile designing.

 

In Designing following practices must carry out for smooth functioning in weaving.

  Total ends / repeat should not be odd otherwise it will create problem in warping



during leasing.

  Use bleach yarn for reactive dye shade instead of grey yarn.



  Do not use very close shade adjacent to each other especially in fila-fil designs.



  For combination weave like Plain + mix weave; take plain weave always in front heald



frame. frame.     Don‟t take more than 1800 ends in one heald frame. 



  Different color ends should not be taken in same dent where lifting is same like mock 



leno, oxford, matt and rib weave.

  Take selvedge ends from bottom beam in case of double beam design.



Best Practices in Weaving Process

Weaving is the process of interlacing two sets of yarns at right angles. The threads which lie along the length of the fabric are known as warp threads, while those which lie across the width are known as weft threads. More technical names for these same threads are ends and

picks

respectively.

The

weaving

or

interlacing of warp and weft threads is accomplished with a machine known as loom.   In order to interlace warp and weft threads to produce a fabric on any type of loom, following operations are necessary.

  Shedding: separating the warp threads into two layers to form a tunnel known as the



shed.

  Picking: passing the weft thread through the shed.



 

  Beating-up: pushing the newly inserted length of weft, into the already woven fabric



at a point known as the fell. After all these operations took place, a weaving cycle

is

completed.

Weaving

cycles

are

repeated over and over again until the cloth reaches the desired length.

In weaving following practices must carry out for better productivity and quality of the fabric.

  Apply count and shade details on each package holder of weft creel to avoid mixing of 



weft during weaving.

  Warp patterns in the fabric must check with the help of swatches.



  Display of denting and drawing plan on loom will help to reduce the weaver related



defects like wrong denting and wrong drawing. To avoid Starting mark defect in the fabric starting mark marking must be done after   startup of new sort.

  Apply standard machine setting after



each gaiting process.

  Always monitor and maintain standard



RPM on loom.

  Always do correct drawing and denting



of false selvedge to avoid fabric defects and warp brakes at selvedges.

  Always knot tail end of running weft package to start end of new weft package to



avoid weft brakes.

  Always use four accumulators for better mixing of weft in the fabric to avoid fabric



defect i.e. weft bar and shade variation.

  Do online checking of fabric at regular interval to avoid any continuous defect.



 

Best Practices in Maintenance

In foregoing discussion only best operational practices are discussed but in order to enhance the probability of accomplishment of final goal of productivity and quality the best operational practices need to be supported by good maintenance management. Ideally, maintenance is performed to keep equipment and systems running efficiently for at least designed life of the components. The design life of most equipment requires periodic maintenance like Belts need adjustment; alignment and proper lubrication on rotating equipment and so on. In some cases, certain components need to be replaced and therefore a maintenance manager manager has to do following types of maintenance activitie activities. s.

breaks”  1.  Breakdown Maintenance: “run it till it breaks”  2.  Preventive Maintenance: “Periodic checking, adjustment and replacement”  replacement”  3.  Predictive maintenance: “ Maintenance on actual condition of the machine components by judging performance, abno abnormal rmal worn-out, noise & vibration rather tthan han on some preset maintenance schedule” schedule”  Preventive and Predictive Maintenance are the best maintenance practices over the Breakdown Maintenance because

  It Reduces equipment or process failure.



  Flexibility to allow maintenance periodicity.





  Increases component life cycle.   Estimated 12% to 18% cost savings over ov er Breakdown maintenance.



Best Practices in Fabric Inspection

After the production of fabric from loom, woven out fabric sent to inspection department for

checking and grading. Men ding is a tool for removing fabric defect manually; similarly fabric inspection is a tool for satisfying internal as well as external customer by mapping fabric defects in the fabric. External customer can benefit by getting the products as per the specification provided while internal customer benefit by knowing the reason for any down-

 

gradation and can thus correct the same. Fabric inspection also mirrors the packing percentage and associated value losses due to down-gradation. A systematic approach of  inspection is important for proper and timely feedback  to all pre production activities like weaving, weaving preparatory, yarn dyeing and spinning. From weaving department cloth rolls are sent for inspection at various stages of fabric production i.e. just after the starting of  new sort (first piece), in between the running sort (running piece) and at the finish of sort (last piece).First priority must be given to first piece because it will help to rectify fabric defect immediately after the production start and also helps to raise an alert to backward process. Next priority must be given to those cloth roll for which inspection or quality control department has alre already ady raised alert and then after running piece and llast ast piece of the sort.

 

There are many inspection practices and of them four point inspection practice has got wide acceptance and is followed globally by fabric and garment manufactures. Basic requirement of Four Point Inspection System is as follows.  

  The light source must have perpendicular to the



surface of the fabric and the fabric runs at an angle of 45 degree.

  The inspection area surface illumination level



shall be a minimum of 1075 lux.

  Inspect the fabric at a distance of one meter,



while the fabric is in motion.

FOUR POINT INSPECTION SYSTEM:

  Assign defect points based on the length of the defect as mentioned in the following



table.

 

Defect Length ( Inches)

Defect Point

Category

Up to 3

1

Minor Defect

3 to 6

2

Minor Defect

6 to 9

3

Medium Defect

Over 9

4

Major Defect

f abric.   Maximum 24 defect points are permissible in a 100 square meter of fabric.



  Only 20 numbers of defects are permissible in 100 square meter of fabric.



  Only 4, four point defects are permissible in 100 square meter of fabric.



  No Major defect is allowed for first and last one meter of cloth roll.



  Holes with ¼ inches or more considered as cut able defect.



Conclusion Going forward every weaving mill needs to do periodic brainstorming sessions with work  force on each activities which is carried out in day to day work and find out the best ways to do each activities. A continuous education / training of work force will further improvise the best practices. Periodic brainstorming on Standard operating procedures (SOPs) of every activities and strict adherence to SOPs are very much essential. These good practices in process will help to enhance the productivity, quality of fabric, reduction of manpower requirement and stress.

Sponsor Documents

Or use your account on DocShare.tips

Hide

Forgot your password?

Or register your new account on DocShare.tips

Hide

Lost your password? Please enter your email address. You will receive a link to create a new password.

Back to log-in

Close