BSR 2008

Published on May 2016 | Categories: Documents | Downloads: 28 | Comments: 0 | Views: 208
of 65
Download PDF   Embed   Report

Comments

Content

ALL RATES ARE COMMON TO COLOMBO, GAMPAHA & KALUTARA DISTRICTS (Rates effective from 2008.01.01 until further notice)

CONTENTS Description Item A B C D E F G H J K L M N P Q R S T U V W Y Z AA Notes Excavation Concrete Form Work Reinforcement Brick Masonary Hollow & Solid Block Masonary Rubble Masonary Flooring Waterproofing Plastering Tiling Colour Washing, Painting & Polishing Doors & Windows Brass Founder Roofing & Ceiling Gutters & Down Pipes Sanitary Fittings Plumbing Drainage Electrical Installation Metal Work Structural Steel Work Maintenance Work Miscellaneous Annex-1 iii - xiii 1 2 4 5 5 6 6 6 7 8 8 10 11 12 12 14 15 18 21 24 32 38 39 42 a Page

ii

BUILDING SCHEDULE OF RATES General Notes 1. This Building Schedule of Rates (BSR) become operative from 01.01.2008 and shall be valid until further notice. The rates given herein are the maximum rates adoptable in preparation of Bill of Quantities of the estimates for Building Construction, Additions and Improvements and Repair (Maintenance) works. In case where the Resources are available at lesser rates depending on area and locality, such rates are to be used. The rates include an overhead and profit component, but do not include VAT. Provisions should be made separately in the estimate for the payment of VAT and should also allow Contingencies (up to a maximum of 10% of the BOQ total). Provision for price escalation should be separately allowed in the estimate. In preparation of Bill of Quantities, the item description shall conform to that relevant item as appearing in this Building Schedule of Rates, so as to avoid any ambiguity. Recommended cement brand names for concreting, brick masonary and rubble masonary are “Holcim”, “Mahaweli Marine”, “Mitsui”, “Ambuja”, “UltraTech Ceylinco Cement” or any other brand conforming to SLS 1072002 and approved by the Divisional Engineer based on a laboratory test report. The rates indicated herein are valid only for the material conforming to the relevant standards as indicated in the covering letter and also as per under Item (8) and the workmanship and finished quality of work should conform to be following ICTAD specification document series. (a) Specification for Building Work (SCA/4 Volume I) (b) Specification for Sanitary Installation (SCA/4 Volume II) (c) Specification for Water Supply & Sewerage and Storm Water Drainage Work (SCA/3/2). (d) Specification for Electrical and Mechanical Work associated with Building and Civil Engineering (SCA/8). 6. For concrete work, instructions issued by the Circular No. 2/98 and 3/98 of the Engineering Organization are to be adhered to. Before making full payment for concreting work, Divisional Engineer should get at least 3 sample cubes tested for 28 days strength at an approved testing laboratory. The rates for formwork will be applicable only for the relevant form material. Material specifications are as follows : (i) Concrete constituent materials : (a) (b) (c) Cement – SLS 107: 2002 Aggregate – BS 812/BS 882 Steel Reinforcement – SLS 375/1996

2.

3.

4.

5.

7. 8.

Concrete mixers should be used for all reinforced concreting exceeding 1 (one) Cube. Poker vibrators should be used to compact the concrete irrespective of the volume.

iii

(ii) Ready-mix concrete shall conform to SLS 114 (iii)Hollow Blocks shall conform to SLS 855 (iv) Structural steel shall conform to BS 4360 (v) Aluminium extrusions shall conform to BS 1474 and BS 1615 and extruted from AA 6063 (vi) Structural steel should be of or 43 to conform to BS 7668: 1994 (vii) List of approved electrical fittings are as follows. LIST OF APPROVED ELECTRICAL FITTINGS No. 01 02 03 04 Item Sunk Switches 10A 13A Switched Socket Outlets, plugs & Adopters 5A and 15A Switched Socket Outlets R.C.C.B./R.C.D. Relevant Standard Specifications B.S. 3676 B.S. 1363 B.S. 546 B.S. 4293, IEC 1008, BS EN 61008 Recommended Brand Names Legrand, M.K., K.I.K, Orange Legrand, M.K., K.I.K., Orange Legrand, M.K., K.I.K., Orange F & G (Australia) Siemens (Germany) Crabtree (U.K.) Merlin Gerin (France) Legrand (France) F & G (Astralia) Siemens (Germany) Crabtree (U.K.) Merlin Gerin (France) Legrand (France) ABB (Germany) ABC (Singapore) Crabtree (U.K.) Hager (France) Legrand (France) Legrand (France) Merlin Gerin (France) Terrasaki (Japan) Klokner Moeller (Germany) Crabtree (U.K.) ACL (Sri Lanka) Wilson (Singapore) Kelani (Sri Lanka) ACL (Sri Lanka) Wilson (Singapore) Kelani (Sri Lanka) Schwabe (Germany) ATCO (Australia) B.G. (U.K.)

05

M.C.B.

IEC 898 or BS.EN 60898 or IEC 947-2 or B.S. 3871:Part I B.S. 5486 Part I & Part 13, LEC 439-1 or BS EN 60439-3 IEC 695-2-1 L.E.C. 947-2:1989 BS EN 60947-2:1992

06

Consumer Unit

07

M.C.C.B.

08

Cu/PVC/SWA/PVC Cables Cu/PVC/PVC Cables

B.S. 6346 B.S. 6004:1995 & SLS 733:1995 B.S. 5467B.S. 5467

09

Cu/XLPE/SWA/PVC Cables Cu/XLPE/PVC Cables Fluorescent Ballasts with Screw Type Terminals

10

I.E.C. 920, 921 & 922 ESEN 60928

iv

11

Fluorescent Lamps Colour : Cool White (4000K)

IEC 81 B.S. 1853

Osram (Germany) Tungsram (Hungary) Philips (Holland) GE (USA) Sylvania (USA) Westinghouse (USA) Elsteel (Sri Lanka) Legrand (France) Himel (Spain) Enlotek (India) Metalix (Sri Lanka) KDK (Japan) Alstom (UK) National (Japan) National, Authon, Duro, S-lon. Matsushita, Maruichi, Pusan or any U.L. approved U.S. Brands. Richardson Projects (Pvt.) Ltd. KDK, National

13

Steel Enclosures (Epoxy Powder coated finish)

I.E.C. 529 for degree of protection BSEN 60529

14 15 16 17 18

Exhaust Fans PVC Conduits G.I. Conduits Moeller Ceiling Fans

BS 5060 I.E.C. 879:1987 BS 4607 & BS 6099 BS 4568 Part I

List of Cable brands in Sri Lanka with SLS Certificate ACL, KML, KELANI, ALUCOP, RUHUNU, KAMAL (vii) The following timber species should be used for construction work unless otherwise specifically stated in the description of the BOQ. Timber Usage for BSR Trade Items (a). Roof frame and ceiling frame Approved Timber Alubo, Bato Domba, Bedi-Del (Wal-Del), Burutha, Dambu, Daw, Dawata, Domba, Dun, Etatibiriya, Gammalu, Hadewaka, Halmilla, Hora (Pressure Impregnated), Liyan, Mee, Na, Palu, Teak, Treated Kempas, Thawvama, Uberiya, Welipana, Wewarana. Imported timber Balau, Bitis, Kampur, Kempus, red Balaue, Merbau (b). Door, Window and Fanlight, Weld mesh frame Alubo, Bata-Domba, Bedi-Del (Wal Del), Balau, Bitis, Burutha, Dambu, Dawata, Domba, Dun, Etatimbiriya, Hadewaka, Halmilla, Ketakara, Kohomba, Kolon, Kumbuk, Liyan, Mee, Milla, Na, Palu, Sooriyamara, Teak, Thawvama, Uberiya, Welang, Wewarana, Welipana. Halmilla, Kirihambiliya, Kohomba, Kolon, Mahogany,Sooriyamara, Teak, Uberiya.

©. Door, Window & Fanlight Sashes

v

(d). Timber Ceiling Planks, Panelling (e). Valance/Barge Boards (f). Partition Frame (g). Floor Boards (h). Furniture Items

Cyprus, Eucalyptus Microcoris, Kirihambiliya, Lunumidella, Tualang Ginisapu, Kumbuk, Wal-Del Cyprus Na, Kubuk,Sooriya mara Etatimbiriya, Hooriyamara, Kolon, Kohomba, Mahogany, Mee, Na, Nadun, Sooriyamara, Teak.

(viii) All PVC pipes shall conform to SLS 147. 9. The approved rates for the following trade items listed in the following table are meant for single storeyed (Ground floor only) buildings. Hence, allowances to be made in the rates for lift in respect of work on upper floors. The percentages indicated in the Table below should be added to obtain the rates applicable to the upper floors. Items Formwork (Sqrs) Plastering (Sqrs) Floor Tiling (Sqrs) Wall Tiling (Sqrs) Roof Calicut Tile (Sqrs) Roof asbestos (sqrs) Ceiling Works (Sqrs) Painting (Sqrs) First Floor 3% 5% 2% 2% 3% 3% 3% 3% Second Floor 5% 10% 4% 4% 6% 5% 5% 6% Third Floor 7% 15% 6% 6% 9% 7% 7% 9%

10. Following conversion factors should apply for the rates when it is necessary to convert from the Imperial Units to Metric. Conversion: Imperial to Metric factor (1foot x 0.3048 = metre) To convert Rate per Cube Square Sq.ft. L.ft. Cwt. To Rate per M3 M2 M2 M Kg Multiply the Present Rate by 0.35 0.108 10.76 3.28 0.02

vi

11.

IRON and STEEL gauge systems Standard Wire Gauge. Birmingham Wire Gauge BWG mm inch

No.

SWG mm inch

20 18 16

0.914 1.219 1.626

0.036 0.048 0.064

0.996 1.257 1.588

0.0392 0.0495 0.0625

12. Units To convert “Litres to “Galloons” multiply by “Miles to “Kilometers” multiply “Kilo to “Pounds” multiply by 13. Steel Dia. Mm 25 20 16 12 10 6 Dia. Inch 1 3/4 5/8 1/2 3/8 1/4 Normal Weight Kg per meter 3.854 2.466 1.578 0.888 0.617 0.222 0.2205 1.609 2.205

14. Method of Measurement shall be done in accordance with SLS 573:1999 (Revised) edition. 15. Incorporation of a preliminary bill for works costing over Rs. 500,000/= is mandatory. Please refer Annexure for sample preliminary bill items. The values indicated are only for guidance and you are advised to insert only the relevant items and cost based on contract period and amount of contract. 16. The trade names, brand names along with catalogue numbers have been used purely to describe certain items in order to fully describe the expected quality, appearance, finish and performance characteristics of the relevant fitting. However, mere appearance of the brand name does not mean to restrict to that particular brand and any other brand having similar characteristics are acceptable provided prior approval is obtained for use of such brands. 17. Following item descriptions shall be used to describe the water proofing in side toilets, and measurements to be taken accordingly.

vii

(a). Water proofing inside shower areas and toilets : Application of water proofing agent “Barralastic” or an approved equivalent brand to the entire toilet floor and up to 1.50 m (5’-0”) height on to the masonry wall the function between the wall and concrete floor shall be treated with a non-wooyen reinforced fiber mesh entire work shall be done in conformity to the manufacturer’s specifications. This item is payable only upon the submission of a written guarantee jointly by the Contractor and the water proofing material supplier. (b). Certificate for Water Proofing: Contractor shall submit a written certificate to the effect that all the material used and workmanship was in conformity to the water proofing material manufacturer’s requirements and has been installed as per the manufacturer’s specifications. ©. Warranty for Water Proofing: Contractor shall submit a 10 year written warranty jointly with the water proofing manufacturer/Supplier to the effect that “The treated surface has a 10 year warranty against dampness/and/or moisture penetration due to defective workmanship and/or defective material and that in the event of a failure, the material equipment and labour necessary for the rectification work will be provided free of charge. 18. Guide for Preparing a Preliminary Estimate for proposal identification. 1. Visit the site and make a note on the field book : (i) Ownership of the land and availability of survey plan and contour survey plan (ii) Soil types up to 6’-0” depth. Classify soil as Sand Clay Sandy clay (if a sand content is more than 50%). Clayey sand Peat.

(iii)Depth of water table under normal weather condition. (iv) Disposal of rain water is the site to be filled ? is the main drain available in the road ?

(v) Necessity of leveling/filling the ground, retaining walls, boundary wall, fence, gate and culvert (either Hume pipe or concrete slabs over masonary/concrete drain). (vi) Pipe water with pump + Overhead tank Well water with pump + overhead tank.

viii

In case of a new well to dig; get a location yield and water quality check from the Water Supply & Drainage Board of from Water Resources Board. Preliminary investigation Rs. 26,250/= Detailed investigation Rs. 300,000/= (They will give a detailed estimate after preliminary investigation).

(vii) Availability of electricity. 2. Desk Study and Preparation of an Itemized Estimate (without a B.O.Q.) The covering letter should read as ………………………………………….. The tentative cost estimate for the proposed work is Rs. ………… The break-up of item costs are as given below. The detailed estimate will be forwarded upon the approval of plans and after preparing a detailed B.O.Q.. In the mean time, please obtain the local authority approval for the construction

Items to reflect in the tentative estimate are : (a) Construction of the proposed building (@ 2750/= per Sq.ft. on hard ground) (@ 3200/= per Sq.ft. on soft ground) (@ 3400/= for storeyed buildings on hard ground) (@ 3800/= for storeyed buildings on soft ground). (b) Construction of gate 12’-0” wide and culvert = Rs. ………………. = Rs. ……………….

©.1 Construction of boundary wall of 6’-0” height @ 2500/= per L.ft. = Rs. ……………….. or ©.2 Construction of a fence with PVC coated metal wire to 5’-0” height with plinth wall @ 3000/= per L.Ft. = Rs. ……………… (d) Soil investigation fee (for two bore holes) = (e) External service connection – 3 phase = (f) External water supply or well + sump + O.H. tank = Sub Total = Rs. 70,000/= Rs. 50,000/= Rs. ……………… X A B X+A+B =========== Rs. Q Rs. P+Q Rs.

Add 10% as Contingencies = Add 10% of (or 5% for less than 6 months) as price Escalation = Total approximate Cost Add 15% VAT Total Estimated cost T.E.C Rounded to nearest Thousand. P = = =

ix

3. Preparation of a Detailed BOQ Upon the receipt of an allocation this is how to proceed. (a) Submit the Survey Plan (should be a scaled plan without reduction during copying), confirm the ownership of the land, and functional requirements of the building to the Architect through Director (Buildings) or Director (Engineering). (b) Arrange a site inspection with the Architect, Chief Engineer (Designs), Chief Engineer (W.S. & S). (c) Get the Architectural Sketch Plan approved from the Head of Institution concerned. (d) Send a copy of the approved Architectural Sketch Plan to the Architect (with or without modifications) to prepare the Council Drawings. (e) Inform the Client to get the local authority approval based on Council drawings.

(f) In the mean time, following drawings shall be obtained before proceeding with the preparation of the detailed BOQ. 19. Detailed Architectural Drawing including floor plans, elevations, sections, door/window schedule, finishing schedule, staircase and railing details, ceiling details. Structural Drawings including foundation details, columns, floor beams/slabs/stairs, roof frame work (if necessary, ceiling frame work), retaining walls etc. Water supply, waste water, sewerage, plumbing layout drawings including drain pipe positions, cleaning eyes, floor gullies, manholes, septic tanks and soakage pits. Electrical layout plan including wiring diagram, fitting locations, mains, D.B.s locations etc. External storm water (rainwater) disposal drawing.

Only upon the receipt of the above detailed drawings shall the BOQ be prepared. Rate to be Comprehensive The rates for each item of measured work, must be comprehensive and must include for complying with the details on the drawings, description in the bills of quantities, relevant specifications, cover all the obligation under the contract and all matters and things necessary for the proper construction, completion and maintenance of the works. In the preparation of the BOQ, following act as a guideline. 1. BOQ item descriptions shall be as per BSR item description wherever possible.

x

2. 3. 4. 5. 6.

Preamble notes shall be used with the BOQ. Follow the standard method of measurement SLS 573:1999 (revised edition) to extract the quantities from the drawings. A preliminaries bill is mandatory for all works costing over Rs. 500,000/=. In case of type plans, ensure the ground conditions meet with the prescribed soil bearing pressure appearing on the structural plan. In the respective BOQ trade items, indicate the following . “Contractor shall submit the following samples for approval when requested to do so. (a) (b) (c) (d) (e) (f) (g) (h) (i) (j) (k) (l) Brass hinges, casement stays, door locks, door closers Sample aluminium sections along with a test report Mix design report for the ready mix concrete Samples of bib taps, gate valves, sanitary fittings fixtures Ceramic tile samples Electrical fittings Timber samples for door/window frames Specific guarantees from the manufacturer/authorized agent for sanitary fittings, door locks, ceiling fans, electrical accessories of MCB, MCCB, RCCB, water proofing material Water pressure test report for the plumbing system Electrical system test from a Chartered Electrical Engineer Slump test and concrete cube test is mandatory for all concrete work. In case of earth compaction, the field density of the fill shall be measured with the sand cone method or any other appropriate method.

20.A Item

Preliminary Bill (for Works between (0.5m–1.0m), (1m–5m),(5m–10m), (10m–25m) Description 0.5m-1.0m 10,000/= 1 m-5m 5m-10m 10m-25m

20.A.1 Allow lump sum to construct, furnish and maintain Contractor’s site office. 20.A.2 Allow lump sum to protect materials and plant. 20.A.3 Allow lump sum to obtain electricity and water for the site. 20.A.4 Allow lump sum for the provision of sanitary facilities to be Contractor’s staff. 20.A.5 Allow lump sum to barricade the site with a fence and a gate. 20.A.6 Allow lump sum for providing a name board of (size to define) and to erect at a 7’-0” height.

15,000/= 25,000/= 30,000/=

3,500/= 5,300/= 3,200/=

4,500/= 7,500/= 5,000/=

6,000/=

10,000/=

12,000/= 15,000/= 5,000/= 7,000/=

_ _

4,000/= _

4,000/= 1,500/=

6,000/= 1,900/=

xi

20. A.7. Allow lump sum for insurance, performance bond and guarantee = Rs. 4,800.00 per one million projects For projects costing over 5m, contractor shall employ to following personal 20. A.8 Construction management services (Engineer, Technical Officer) Rate Per Month 1. Graduate Engineer with 3 Years experience = Rs.25,000.00 Rs.40,000.00 20.B Preliminary Bill (for works costing over Rs. 25 Million)

2. NCT qualified Technical officer with 3 Years experience = Rs.15,000.00

Divisional Engineer to decide on the necessity of each and every item for the work concerned. The total preliminary cost is in the range of 3-4% of the building construction cost. 20.B.1. Allow lump sum for providing performance bond, insurance/bank guarantees – payment to be done either for the actual amount or for the quoted sum which ever is less. 20.B.2. Allow lump sum for insurance against the following: (a) (b) (c) (d) (e) (f) (g) Work at site and property Accident and injury to workmen Third party Material Theft Riot and civil commotions Flooding.

20.B.3 Provision of a sum to construct, furnish and maintain site office for the Consultant’s staff the requirements are : 12’-0”x 10’-0” Office with a toilet 2 No. 3’-6”x 2’-0” Tables with lockable drawers and 6 No. plastic chairs. One ceiling fan with two lights Steel four drawer cupboard Water filter and water heater 3 pairs of gun boots and 3 helmets Drawing rack 4’-0”x 2’-0” Display board Pentium III Computer with a Dot matrix printer (wide carriage) Direct telephone line with fax First-Aid Box Measuring Tape (20m).

xii

20.B.4 Provision of a sum to construct, furnish and maintain a site office for the Contractor’s staff. 20.B.5 Provision of a sum to construct and maintain facilities for Contractor’s staff accommodation 20.B.6 Provision of a sum to construct sanitary facilities for workmen 20.B.7 Provision of a sum to construct facilities to store materials and plants. 20.B.8 Provision to supply and temporary storage of water including plumbing work an d service connection or to use the Client’s facility and to make a monthly payment. 20.B.9 Provision to obtain temporary electricity connection and maintain throughout the construction period. 20.B.10 Provision to erect fence, barricades (describe) 20.B.11 Provision to safeguard the works, material and plants against theft, Watchers including provision for shelter and torches. 20.B.12 Allow lump sum for maintaining temporary roads 20.B.13 Allow lump sum for safety, health and welfare of the workmen as per statutory requirements 20.B.14 Setting out of the works through a licensed Surveyor and submission of a sign survey drawing of the premises. 20.B.15 Establishment of permanent bench works and reference points of the column/building grids. 20.B.16 Erection of a sign board with the building elevation on a screen point fixed to a G.I. frame work of 6’-0”x 4’-0” at 7’-0” above Ground level (letter height 3”). 20.B.17 Allow for the Construction management (resident Engineer and Technical Officers ….. ) described throughout the construction. 20.B.18 Employment of a Quality Assurance Engineer under the direct supervision of the Consultant and to establish a quality assurance system including documentation. 20.B.19 Hiring of a air-conditioned vehicle with driver for the exclusive use of the Consultant throughout the construction period. Maximum per month mileage of 300km and only on week days between 8.00 a.m. and 6.00 p.m. 20.B.20 Allow for scaffolding (describe) 20.B.21 Allow for survey equipment, slump cone, cube moulds 20.B.22 Preparation of As-built drawings of A-1 size for the entire building including structural services and landscape. 20.B.23 Cleaning the building including dis-infection of sanitary fittings and premises including carting away debris and submission of a list of moveable and xiii

permanent fittings and fixtures.

xiv

Item

Description B - EXCAVATION Clearing site vegetation, including bushes, removing shrubs and top soil to a depth not exceeding 6" and removing away from site. Manual Excavation over site to reduce level in any material (except rock requiring blasting) including depositing and levelling as directed up to a distance not exceeding 30'. Manual Excavation over site to reduce level in any material except rock requiring blasting including depositing and levelling as directed exceeding 30'-0" distance but not exceeding 1/4 mile. Manual Excavation for column,wall,staircase foundations in any material (except rock requiring blasting) up to 5'0" depth, part return fill in and ram and surplus depositted within site as directed. (Shoring, dewatering blasting up to 5'0" depth if mecessary, shall be paid for separately) Bulk excavation using machinery to be paid for as per item B12 Earth work support (Open planking) in trenches up to a depth of 5'0". Earth work support (Close planking) in trenches up to a depth of 5'0". Approved earth shall mean filling materials that comply to the following : The earth shall be free of vegetation, roots, boulders, easily decomposable materials, chemicals, industrial waste, plastic etc. The maximum size of particle shall not exceed 75mm. The earth shall be well graded and the silt and clay (fines) content shall not be more than 30% Approved hard Earth spreading , leveling watering and manual compaction, using standered cast iron stamper or equivalent and filling in 3"-6" mm thick layers (loose volume) in respected area (Earth available at site) Approved earth supplying within 16 Km from the source and piled at site (measured at piled volume)

Unit

Rate

B01

Sqr.

750.00

B02

Cube

1130.00

B03

Cube

1280.00

B04

Cube

1645.00

B05 B06

Sq.ft. Sq.ft.

69.00 120.00

(a)

(b) ( c)

B07

Cube

960.00

B08

Cube

1800.00

B09 B10

Transport of Earth per Km per cube for over and above 16 Km River sand supply within 16km from the source (for distances over 16km, add Rs. 75 per Cube per Killo Meter) subject to the specific approval by the Divisional Engineer) Rate is applicable for loose volume. In case of measurements to be done on compacted volume multiply the rate by 1.2. Compaction of Earth including watering in 9" layers (measured on piled volume ) using machine Rammer. (Rate include hire charges of the machine .) This rate is applicable for building construction with earth work not exceeding 50 cubes. (earth available at site). Manually spreading and leveling piled approved earth H.S.R. item Ew1 -002 (applicable for filling out side the building area) rate without compaction Bulk excavation using machinery C - CONCRETE Note: The quality of the concrete should confirm to the relevant B.S., S.L.S. and ICTAD specification for Building works. Refer General notes for approved cement brands. IN - SITU PLAIN CONCRETE Cement concrete 1:3:6( 2" ) in wall foundation (Mass concrete) Cement concrete 1:3:6(1 1/2") in foundation under column footings (concrete mixer) Cement concrete 1:3:6(1 1/2") in foundation under column footings (lean concrete of 3" thickness) Cement concrete 1:3:6(1") in foundation under column footings (lean concrete of 2" thickness) Cement concrete bedding1:2 1/2:5(1") in Toilets/Garage/Factory floors IN - SITU REINFORCED CONCRETE

1 Km Cube

120.00 6400.00

B11

Cube

775.00

B12

Cube

250.00

B13

Cube

725.00

1

2 C01 C02 C03 C04 C05

Cube Cube Sqr. Sqr. Cube

23225.00 24730.00 6180.00 3950.00 25840.00

C06 C07 C08 C09

Cement concrete 1:2:4(3/4") footings, beams/lintels and columns in ground floor using mixer and vibrator Cement concrete 1:1 1/2:3(3/4") using mixer and vibrator in Ground floor Cement concrete 1:1 1/2:3(3/4") using mixer and vibrator in first floor Cement concrete 1:1 1/2:3(3/4") using mixer and vibrator in second floor

Cube Cube Cube Cube

30990.00 33425.00 34420.00 35095.00

C10 C11 C12 C13 C14 C15 C16 C17

Cement concrete 1:2:4(3/4") in beams/lintels and columns in first floor using mixer and vibrator. Cement concrete 1:2:4(3/4") in beams/lintels and columns in second floor using mixer and vibrator. 4" Thick slab in first floor with cement concrete 1:2:4(3/4") using mixer and vibrator. 4 1/2" thick R.C.C. slab in cement concrete 1:2:4(3/4") in first floor using mixer and vibrator. 5" thick R.C.C. slab in cement concrete 1:2:4(3/4") in first floor using mixer and vibrator. 5 1/2" thick R.C.C. slab in cement concrete 1:2:4(3/4") in first floor using mixer and vibrator. 6" thick R.C.C. slab in cement concrete 1:2:4(3/4") in first floor using mixer and vibrator. Pre-cast lintols size 9"x6" deep in 1:2:4(3/4") Concrete, reinforced with 3 No 10mm dia. Tor steel bars and MS stirrups of 6mm @ 8" c/c including necessary formwork Pre-cast lintols size 4 1/2"x6" deep in 1:2:4(3/4") Concrete, reinforced with 2 No 10mm dia. Tor steel bars and M.S. stirrups of 6mm @ 6" c/c including necessary formwork. Cement concrete drains in 1:3:6(1 ") of 6" wide and 9" average depth, 3" thick sides and base including 1:3 rendering to 1/2" thickness, without ramp including necessary formwork. Cement concrete - do - with concrete ramp 3" thick and 2'6" width. Cement concrete - do - with concrete ramp 3" thick and 1'6" width. Construction of concrete drain 300mm width x 350mm depth and varies up to 400mm. Rate include for necessary excavation in hard earth, 75mm thick concrete base and walls in Grade 20 concrete, fair finish internal surface with size 450mm wide x 600mm long, 75mm thick Grade 20 removable cover slabs with side formwork. Drain and cover slab reinforced with tor steel 10mm at 150m c/c both ways.

Cube Cube Sq.. Sqr. Sqr. Sqr. Sqr. L.ft.

31920.00 32540.00 10900.00 11850.00 12800.00 14190.00 15200.00 300.00

C18

L.ft.

240.00

C19

L.ft.

440.00

C20 C21 C22

L.ft. L.ft. L.ft.

690.00 415.00 640.00

C23

Construction of concrete drain 450mm width x 600mm minimum depth and varies up to 750mm. Rate include for necessary excavation in hard earth, 100mm thick concrete base and walls in Grade 20 concrete, fair finish internal surface with adequate slab, 75mm thick Grade 20 removable cover slabs with side formwork. Drain cover slab and drain cover slab reinforced with tor steel 10mm at 150m c/c both ways. Casting of 6"x6"x6" concrete cubes on a steel mould, curing for 7 days and testing for compressive strength at an approved laboratory (rate includes transport of cubes from site to laboratory ). READY MIX CONCRETE

L.ft.

820.00

C24

No.

1100.00

C25

Ready mix concrete of grade 20 (20 N/mm2) confirming to SLS 144-1997, transport from batching plant and delivered to the site (slump of 12 Cm) -Ditto- grade 25 (25 N /mm2) -do-Ditto- grade 30 (30N/mm2) doPlacing , leveling and vibrating the concrete. Hire charges for concrete pump car per day (up to 30 m3) For more than 30 m3 additional pumping charges. (Rate for every m3 over and above 30 m3) D - FORM WORK Note: The rates given for items D02,D03 to D08 herein are applicable for plywood sheets of 15 mm thick. Hence the rate is valid only if the shuttering / formwork for footing , column , beams , lintel, walls, slabs are of 15 mm thick ply boards. Any deviation from the specified materials, specified thickness and the arrangement of formwork given in this document should require the written approval of the Divisional Engineer. Rate for such deviation from the item description will be decided by the D(B/SW)

Cum.

8964.00

C26 C27 C28 C29 C30

Cum. Cum. Cum. Item Cum

9125.00 9370.00 400.00 12000.00 400.00

a)

c)

D01

Shuttering for sides of foundation with 1" thick rubber planking including dismantling For ordinary plywood of 15mm thick boarding as shuttering, (Even for WBP sheets the same rate shall be applicable).

Sqr

3700.00

D02

Shuttering of sides and bottom for plinth beams, ground beams including dismantling in 15mm thick plywood board. Shuttering for floor slab including dismantling in 15 mm thick Plywood board. Shuttering for columns including dismantling in 15mm thick Plywood board. Shuttering for Beams/Lintols including dismantling in 15 mm thick Plywood Board Shuttering for floor slab including dismantling in 15 mm thick Plywood board support by scaffolding up to 12'. Shuttering for floor slab including dismantling in 15 mm thick Plywood board support by scaffolding up to 16'. Shuttering for Beams/Lintols including dismantling in 15 mm thick Plywood Board support by G.I Jack. The Note : rates given in Items D11,D12,D13 herein are applicable for Rubber planks. The rubber planks are allowed only for minor works and should be used with the written approval of the D.E.

Sqr

10260.00

D03 D04 D05 D06 D07 D08

Sqr. Sqr. Sqr. Sqr. Sqr. Sqr.

8900.00 11900.00 14800.00 8780.00 9270.00 14300.00

D09 D10 D11 D12 D13

Shuttering for floor slab including dismantling. Shuttering for columns including dismantling. Shuttering for Beams/Lintols including dismantling. Shuttering for stiffener columns between wall panels in 9" walls, 4 1/2" walls and in boundary walls. Shuttering for R.C.C. copings in top of balcony , stair and boundary walls and pre - cast lintel sides E - REINFORCEMENT Mild steel reinforcement to slabs, beams, lintels, columns ,footings etc. bent to shape, laid in position and tied with 16 B.W.G. binding wire in Ground floor . Mild steel reinforcement to slabs, beams, lintels, columns ,footings etc. bent to shape, laid in position and tied with 16 B.W.G. binding wire 1st floor. Mild steel reinforcement to slabs, beams, lintels, columns ,footings etc. bent to shape, laid in position and tied with 16 B.W.G. binding wire 2nd floor. Tor steel reinforcement - do Tor steel reinforcement - do Tor steel reinforcement - do - do - in Ground floor. - do - in 1st floor. - do - in 2nd floor.

Sqr. Sqr. Sqr. Sqr. Sqr.

Deleted Deleted 5700.00 5100.00 3700.00

E01

Cwt.

8660.00

E02

Cwt.

8920.00

E03

Cwt.

9090.00

E04 E05 E06

Cwt. Cwt. Cwt.

9290.00 9460.00 9755.00

E07 E08

Rate for testing of Tor-steel specimen of 1m length for mechanical properties at an approved laboratory. Application of two coats of Corrosion resistant primer of " BARRA ZINC SP" or equivalent to all exposed reinforcements. F - BRICK MASONRY Brick work in cement and sand 1:8 in foundation up to D.P.C. level. Brick work in cement and sand 1:8 in super Structure in ground floor. ( 9" thick brick work) Brick work in cement and sand 1:8 in 1st floor level.(9" thick brick work) Brick work in cement and sand 1:8 in 2nd floor level.(9" thick brick work) Brick work in cement and sand 1:8 in superstructure in ground floor (8" thick brick work) Brick work in cement and sand 1:8 in 1st floor level.(8" thick brick work) Brick work in cement and sand 1:8 in 2nd floor level.(8" thick brick work) Brick work in cement and sand 1:5 in 4 1/2" thick walls in ground floor. Brick work in cement and sand 1:5 in 4 1/2" thick walls in 1st floor Brick work in cement and sand 1:5 in 4 1/2" thick walls in 2nd floor Brick drain internal size 9"x9"(average depth) including excavation, back filling, 3" thick plain concrete (1:3:6(1") base, 4 1/2" thk. Brick side walls in cement and sand (1:5), render 1/2" thick cement and sand (1:3) and finish smooth with cement putty. 3" thick brick paving in cement and sand 1:8 mix 4 1/2" thick wire cut brick wall in cement and sand 1:5 in ground floor 9" thick wire cut brick wall in cement and sand 1:5 in ground floor. Steps 1' - 1 1/2" in brick in cement and sand 1:5 with 1/2" thick rendering in cement and sand 1:2 including 6" high foundation. Brick work 1:5 in piers. G - HOLLOW AND SOLID BLOCK MASONRY

sample L.ft.

3800.00 70.00

F01 F02 F03 F04 F05 F06 F07 F08 F09 F10 F11

Cube Cube Cube Cube Cube Cube Cube Sqr. Sqr. Sqr. L.ft.

21780.00 22570.00 23700.00 24150.00 18400.00 18790.00 19310.00 9425.00 9900.00 10000.00 335.00

F12 F13 F14 F15

Sqr. Sqr. Sqr. L.ft.

6715.00 12840.00 24390.00 240.00

F16

Cube

24000.00

G01

8" thick cement sand Hollow block wall (blocks confirming to S.L.S. 855 and subject to the approval of the quality of the blocks) in cement and sand mortar 1:5 in G.F. 6" thick cement sand Hollow block wall (blocks confirming to S.L.S. 855 and subject to the approval of the quality of the blocks) in cement and sand mortar 1:5 in G.F. 4" thick cement sand Hollow block wall (blocks confirming to S.L.S.855 and subject to the approval of the quality of the blocks) in cement and sand mortar 1:5 in G.F. 8" thick cement sand Solid block wall (blocks confirming to S.L.S. and subject to the approval of the quality of the blocks) in cement and sand mortar 1:5 in G.F. 6" thick cement sand Solid block wall (blocks confirming to S.L.S. and subject to the approval of the quality of the blocks) in cement and sand mortar 1:5 in G.F. 4" thick cement sand Solid block wall (blocks confirming to S.L.S and subject to the approval of the quality of the blocks) in cement and sand mortar 1:5 in G.F. supply and fixing 1' x 1' cement grill on wall supply and fixing glass blocks size 6" x 6"

Sqr.

15700.00

G02

Sqr.

10750.00

G03

Sqr.

7630.00

G04

Sqr.

Deleted

G05

Sqr.

10870.00

G06

Sqr.

8010.00

G07 G08

No Sqr.ft

90.00 720.00

H01

H - RUBBLE MASONRY Random rubble (6"-9") masonry in cement mortar 1:5 in wall foundation and retaining walls. J - FLOORING 3/4" thick D.P.C. in cement sand 1:2 finished with 2 coats of D.P.C. tar and blinded with sand. Gauge 700 polythene damp proof membrane with 6" laps laid under floors Rendering 1/2" thick in cement and sand 1:2 in exposed concrete surfaces and garage floors finished smooth with neat cement slurry. Rendering - do - with colour pigment. ( Pigment added at 2.5 Kg / Sqr ) Rendering 1/2" thick in cement and sand 1:3 in R.C.C. floors and paved floors finished smooth with neat cement slurry and colour pigment. Rendering 1/2" thick - do - without colour pigment.

Cube

17550.00

J01 J02 J03

Sqr. Sqr. Sqr.

5790.00 300.00 3610.00

J04 J05

Sqr. Sqr.

4250.00 3730.00

J06

Sqr.

3180.00

J07

J08 J09

Skirting 4" x 1/2" thick in cement and sand 1:3 projected or flush to walls finished with cement floating including forming groove. Skirting 4" x 1/2" thick - do - with colour pigmented neat cement. Skirting 6" x 1/2" thick in cement and sand 1:3 projected flush to walls finished with cement floating including forming grove in neat cement slurry. Skirting - do - with colour pigmented neat cement. 3" thick brick paving in cement sand 1:8and cement rendered in 1:3 (1/2" thick) floated with neat cement. 3" thick brick paving - do - neat cement and colour pigment. Floor cement concrete in 1:2 1/2":5(1") to a thickness of 3" with 1/2" rendering 1:2 with expansion joints filled with cement and sand. Brick work in cement 1:5 wearing & throating on 41/2" brick wall including 1/2" thick 1:3 cement rendering Brick work in cement 1:5 wearing & throating on 9" brick wall including 1/2" thick 1:3 cement rendering Water Proofing The rates for Items J16, J17,J18and J19 are strictly applicable, subject to the fulfillment of the following conditions. The waterproofing contractor (or sub-contractor) should be a registered specialist contractor at the ICTAD on the particular area. The Contractor should sumit a written warranty of at least 5 year to cover on the quality of the material, suitability of the material for the situation and the workmanship including water tightness. The water proofing material shall conform to relevant British, Euro or ASTM specifications Application of liquid polymer cement water proofing agents for the following areas: Water Proofing the inner surface of walls and floor slab of toilets and balconyes where a waterproofing is necessary before tiling,Application of "Baralastic" polymer modified cementitious waterproofing agent after cleaning the subtrate all as per manufacturer's specifications with 10 yesr warranty on application.Rate shall include for ponding test for a 300mm water height kept for a period of 48 hours

L.ft.

52.00

L.ft. L.ft.

56.00 65.00

J10 J11

L.ft. Sqr.

70.00 11350.00

J12 J13

Sqr. Sqr.

11900.00 9990.00

J14 J15

L.ft. L.ft.

180.00 240.00

(a)

(b)

©

J16

Sq.ft.

210.00

J17

Flat roofs, concrete/masonry tanks, wet areas of toilets including bathrooms, exposed balconies, concrete gutters. "Smart flex", "Tharoseal" or any other equivalent product marketed/installed by specialist contractor registered at ICTAD. Application of cementitious type agents on newly cast under ground sumps, swimming pools basements. "Osmoseal", "Xypex", "Vandex" or any other equivalent product marketed/installed by a specialist contractor registered at ICTAD. Application of membrane type agents

Sq.ft.

190.00

J18

Sq.ft.

265.00

J19

on large flat roofs, gutters, basements. "Agro" or any other equivalent product marketed/installed by a specialist contractor registered at ICTAD The above rates include the cost of surface preparation, but do not include the cost of protective masonry screed. The approving authority for equivalent products will be the Deputy Chief Secretary (Engineering)

Sq.ft.

395.00

J20

Supply and installtion of 1'x1'x3" thick interlocking slab paving (grey colour) on 30 mm thick compacted sand bed laid on top of a well compacted earth sub base K - PLASTERING

Sq.ft.

200.00

K01 K02

5/8" thick plastering to plinth wall in cement sand 1:3 including cement floating. Plastering 5/8" thick to walls in cement, lime or equivelent chemical product (Febmix) and sand 1:1:5 finished semirough with wooden float. (Sand to be seived). -Ditto- plaster reveals not exceeding 6" width. Plastering 5/8" thick to walls in cement, lime or equivelent chemical product (Febmix) and sand 1:1:5 finished smooth with lime putty. -Ditto- plaster reveals not exceeding 6" width. Plastering 3/8" thick to soffit of slab, sunshade, sides and soffit of beams stair cases and sides of columns in cement and sand 1:3 including floating with lime putty. Plastering -do - - do - - do - do - in cement and sand 1:3 and finished semi rough with wooden float. Application of plaster coatings of thickness not less than 2mm "Total coat"", Boral coat", or approved equivalent to slab, beam, column facings.

Sqr. Sqr.

3460.00 3480.00

K03 K04

L.ft. Sqr.

80.00 4430.00

K05 K06

L.ft. Sqr.

90.00 5260.00

K07

Sqr.

4950.00

K08

Sqr.

5330.00

K09

Forming drip for sunshade edge cement sand 1: 2 finish semi rough L - TILING Note: Tiles should comply with European standard specification CEN 177. Wall tiling Glazed ceramic wall tiling of size 4"x4" white, supplying and fixing to walls on a 1:3 cement sand mortar layer, and pointed with tile grout to match the tile, (Rate does not include the 1:3 cement sand mortar layer and is separately measured under item L08) Glazed ceramic wall tiling of size 6"x6" white, supplying and fixing to walls on a 1:3 cement sand mortar layer, and pointed with tile grout to match the tile, (Rate does not include the 1:3 cement sand mortar layer and is separately measured under item L08) Glazed ceramic wall tiling of size 4"x4" approved colour supplying and fixing to walls on a 1:3 cement sand mortar layer, and pointed with tile grout to match the tile, (Rate does not include the 1:3 cement sand mortar layer and is separately measured under item L08) Glazed ceramic wall tiling of size 6"x6" approved colour supplying and fixing to walls on a 1:3 cement sand mortar layer, and pointed with tile grout to match the tile, (Rate does not include the 1:3 cement sand mortar layer and is separately measured under item L08) Glazed ceramic wall tiling of size 8"x6" approved colour supplying and fixing to walls on a 1:3 cement sand mortar layer, and pointed with tile grout to match the tile, (Rate does not include the 1:3 cement sand mortar layer and is separately measured under item L08) Glazed ceramic wall tiling of size 8"x 10" approved colour supplying and fixing to walls on a 1:3 cement sand mortar layer, and pointed with tile grout to match the tile, (Rate does not include the 1:3 cement sand mortar layer and is separately measured under item L08) Glazed ceramic wall tiling of size 8"x 12" approved coloured design supplying and fixing to walls on a 1:3 cement sand mortar layer, and pointed with tile grout to match the tile, (Rate does not include the 1:3 cement sand mortar layer and is separately measured under item L08)

L.ft.

75.00

L01

Sqr.

Deleted

L02

Sqr.

19865.00

L03

Sqr.

Deleted

L04

Sqr.

23355.00

L05

Sqr.

20670.00

L06

Sqr.

22680.00

L07

Sqr.

22080.00

L08

Cement and sand (1:3) screed of 1/2" thick backing to receive wall tiles. Floor tiling Note:For Item No. L09, L10 and L11 Shall be Homogenous, Vitreous ceramic floor tiles of industrial grade (heavy duty) Floor tile rate includes the cost of 1:3 motar leveling bed.

Sqr.

3100.00

L09

Industrial grade ( heavy duty) homogeneous vitreous floor tile (mat or glazed) 8"x8" paving on 1:3 cement sand bedding and pointed with tile grout to match the tiles. Industrial grade (heavy duty) homogeneous vitreous floor tile (mat or glazed) 12"x12" paving on 1:3 cement sand bedding and pointed with tile grout to match the tile. Industrial grade (heavy duty) homogeneous vitreous floor tile (mat or glazed) 16"x 16" paving on 1:3 cement sand bedding and pointed with tile grout to match the tile. Supply and laying of 4" high skirting including grouting of tiling conforming to items L09,L10,L11 Supply and laying of 4" high raking skirting at staircase

Sqr.

23530.00

L10

Sqr.

24310.00

L11

Sqr.

26845.00

L12 L13

L.ft. L.ft.

75.00 100.00

Note :
The tiles specified inL12, L13 and L14 are exclusively for residential/non-public area as specified by an Architect. The rate is applicable for tiles manufactured by European standards and are of coloured designed tiles.

L14

L15

L16

Lay Ceramic glazed floor tiles 12"x12" (paving on 1:3 cement sand bedding and pointed with tile grout to match the tile. Lay Ceramic glazed floor tiles 16"x16" paving on 1:3 cement sand bedding and pointed with tile grout to match the tile. Lay Ceramic glazed floor tiles 18"x18" paving on 1:3 cement sand bedding and pointed with tile grout to match the tile. Note : Rate for tiling should include for cement and sand 1:3 backing 20mm thick including pointing and grout to match colours and sizes of tiles to approval. by the Architect.

Sqr.

32765.00

Sqr.

35260.00

Sqr.

31650.00

L17

Polished Granite floor tiles size 2'-0"x 1'-0" laid on 1/2" thick cement sand 1:3 screed level off using cement slurry and 1mm joints to be absolutely in line and flush and grout. Non-slippery bathroom floor tiles (heavy duty) of sizes between 8"x 8" and 16"x 16" paving on 1:3 cement sand bedding and pointed with tile grout to match the tiles.

Sqr.

31095.00

L18

Sqr.

21610.00

M - COLOUR WASHING, PAINTING & POLISHING M01 M02 M03 M04 M05 M06 M07 M08 M09 M10 M11 M12 M13 M14 M15 M16 M17 M18 Note: White washing walls two coats in single storied building including preparing surface. White washing walls two coats in two storied building -doPainting walls with one coat of wall primer Painting walls with two coats of weather shield Painting walls with two coats of emulsion paint Painting walls with one coat of Emulsion paint Painting walls with two coats of snowcem including preparing surface. Cement washing two coats to walls in single storied buildings including preparing surface. Painting walls with enamel paint one coat. Painting walls with Enamel paint two coats. Preparing and painting old wood work with two coats of enamel paint. Preparing and painting new wood work with primer and two coats enamel paint. Varnishing two coats with polyurethane varnish after sand papering and application of sealer coat Wax polishing to timber in panels and floors. Applying one coat of approved type floor polish including smoothing. Painting floors with one coat of quick drying floor paint including washing and cleaning surfaces. Steel anticorrosive paint (one coat) with Primer. Steel Anticorrosive Paint (two coats) with primer Sqr. Sqr. Sqr. Sqr. Sqr. Sqr. Sqr. Sqr. Sqr. Sqr. Sqr. Sqr. Sqr. Sqr. Sqr. Sqrs. Sqr. Sqr. 460.00 475.00 1025.00 1810.00 1445.00 720.00 1765.00 385.00 935.00 1975.00 1900.00 2430.00 2045.00 570.00 1040.00 1350.00 1095.00 1550.00

M19

Labour rate for two coats of Emulsion Painting walls including scaffolding (Paint & Brushes supplied by the client) Labour rate for single coat of Emulsion Painting walls including scaffolding (Paint & Brushes supplied by the client) Labour rate for two coats of enamel painting (Paint & Brushes supplied by the client)

Sqr.

680.00

M20

Sqr.

455.00

M21

Sqr Sqr.

975.00 760.00

M.22 Painting with aluminium or Red oxide paint
N - DOORS & WINDOWS Timber : Refer general note item 8 VI for approved species. Finished door sash size of less than 1" thicknesses not allowed. Glass thickness to be 5mm window sash size of less than 7/8" thicknesses not allowed. N01 Door flush paneled 1 1/8" thick single sash hung on 3 3/4" x 2 3/4" frame and brass furniture Rate without painting and lock Door glazed and paneled 1 1/8" thick single sash hung on 3 3/4" x 2 3/4" frame and brass furniture. Rate without painting and lock Door flush paneled 1" thick single sash hung on 3 3/4" x 2 3/4" frame and brass furniture Rate without painting and lock Door glazed and paneled 1" thick single sash hung with 3 3/4" x 2 3/4" frame and brass furniture. Rate without painting and lock Door 30mm thick plywood ordinary sash single hung on 3 3/4" x 2 3/4" frame and brass furniture. Rate without painting and lock Door 30mm thick plywood (marine) sash single hung on 3 3/4" x 2 3/4" frame and brass furniture. Rate without painting and lock Window glazed 1 1/8" sash and 3 3/4" x 2 3/4" frame with brass furniture. Painting measured separately. Window glazed 1" sash and 3 3/4" x 2 3/4" frame with brass furniture. Painting measured separately. Window glazed 7/8" sash and 3 3/4" x 2 3/4" frame with brass furniture. Painting measured separately. Door/Window ledged, braced & battened with 3 3/4" x 2 3/4" frames and 7/8" thick sash and brass furniture. Sash out of GINISAPU Painting measured separately.

Sq.ft.

740.00

N02

Sq.ft.

755.00

N03

Sq.ft.

710.00

N04

Sq.ft.

635.00

N05

Sq.ft.

440.00

N06

Sq.ft.

520.00

N07 N08 N09 N10

Sq.ft. Sq.ft. Sq.ft. Sq.ft.

830.00 790.00 750.00 730.00

N11

Timber slats with 3 3/4" x 1 3/4" frame , 1" x 2 1/2" vertical slats at 2 1/2" centers. Painting measured separately. P - BRASS FOUNDER Note: All Iron mongary shall be heavy duty and samples should be approved by the D.E. Prior to installation.

Sq.ft.

455.00

P01 P02 P03 P04 P05 P06 P07 P08 P09 P10 P11 P12 P13 P14 P15 P16

Supplying and fixing butt hinges 4" x 2 1/2" brass oxidized. Supplying and fixing butt hinges 4" x 3" brass oxidized. Supplying and fixing casement fastener brass oxidized. Supplying and fixing Heavy duty casement stay - 10" brass oxidized Supplying and fixing fanlight catch - brass oxidized. Supplying and fixing 3" centre pivot - brass oxidized. Supplying and fixing 4" barrel bolt - brass oxidized. Supplying and fixing 6" barrel bolt - brass oxidized. Supplying and fixing 10" tower bolt - brass oxidized. Supplying and fixing Night - latch (Imported) Supplying and fixing mortice lock-Imported chinese Supplying and fixing Union mortice lock-(European make) Supplying and fixing Yale mortice lock-(Italy make) Supplying and fixing mortice lock- Italian Viro) purchase by Mascons or B.M.C Supplying and fixing "Showa" or "Miwa" cylindrical door lock with knob of Japanese make. Supplying and fixing cylindrical door lock of WHITCO Australian make knob locks or equivalent stainless steel or polished brass.

Pair Pair No. No. No. Pairs No. No. No. No. No No. No. No. No. No.

915.00 1070.00 300.00 300.00 305.00 185.00 365.00 450.00 465.00 1000.00 2330.00 4730.00 6050.00 4090.00 6085.00 5400.00

Supplying & fixing medium quality hydraulic door closer P.18 Supplying & fixing heavy quality hydraulic door closer (approved by D.E.)
Q01 Q - ROOFING AND CEILING Roof covering with calicut pattern clay tiles (Timber frame work and ridge covering measured separately).

P17

No. No.

6085.00 8380.00

Sqrs.

5915.00

Q02

Roof covering with corrugated asbestos sheets (Timber frame work and ridge covering measured separately) Asbestos close fitting ridges fixed complete with roofing screws or hook bolts Ridging with calicut pattern tiles bedded in cement lime sand mortar 1:1:4 and coloured to match the tiles. One layer of half round things or asbestos over existing corrugated sheets. 3/4" x 6" wide tongued and grooved lunumidella ceiling boards fixed to underside of existing rafters with brass nails including leveling with timber strip where necessary. Asbestos eaves ceiling with Halmilla coves & fillets. Under side to existing rafter size of fillet to be 1 1/2"x1/2" size of cove moulding 2"x2" Supplying and Fixing finished size 4"x2" Coconut Rafters Supplying and Fixing finished size 3 1/2 "x1 1/2" Coconut Rafters Aluminium Valley gutter of 3'-0" wide in gauge 24 sheets including 3/4" thk. Ginisapu timber boarding finished with two coats of wood preservative. Aluminium flashing of 1'- 6" wide in gauge 24 sheets including 3/4" thk. Ginisapu timber boarding finished with two coats of wood preservative. Aluminium flashing (gauge 24)of 1'-6" wide, bent to shape and fix to wall. (without timber boarding) Flashing G.I. Flashing 20 B.W.G. of 1'6" girth with end laps not less than 6" , turned and tuck up not less 6" in wall and pointed in cement motor 1:2 G.I. Valley gutter of 3'-0" wide in gauge 0.48 sheets including 3/4" thk. Ginisapu timber boarding including two coats of anti-corrosive paint and wood preservative to sheet and boarding. (Only to be specified when repairing an existing G.I. gutter) Zincalum flashing (0.47mm thick) and 1'6" wide bent to shape and fixed to wall (without timber coating) Zincalum Valley gutter of 3'-0" wide in gauge 20 sheets including 3/4" thk. Ginisapu timber boarding including two coats of anti-corrosive paint and wood preservative to sheet and boarding. (Only to be specified when repairing an existing G.I. gutter) Roof Timber

Sqrs.

6640.00

Q03 Q04

L.ft L.ft

170.00 130.00

Q05 Q06

Sqr. Sqr.

15700.00 12260.00

Q07

Sqr.

6620.00

Q08 Q09 Q10

L.ft L.ft L.ft

100.00 75.00 960.00

Q11

L.ft

760.00

Q12

L.ft

250.00

Q13

L.ft.

325.00

Q14

L.ft

1110.00

Q15 Q16

L.ft L.ft

330.00 1120.00

Refer general note item 8 VI for approved timber species. The rate for timber items will remain same irrespective of timber species. Q17 Roof with calicut pattern tiles on local Micro (Eucalyptus Microcoris) or Balau , Bitis or Kempas timber frame work complete with ridge hips etc. Roofing with asbestos corrugated sheets on local Micro (Eucalyptus Microcoris) or Balau , Bitis, or Kempas timber frame work (Ridging measured separately). Asbestos flat ceiling fixed with coves & fillets to local Micro (Eucalyptus Microcoris) or Balau , Bitis or Kempas timber frame work of 4" x 2" @ 4' - 0" c/c 2" x 2" @ 2' - 0" c/c fillet size to be 1 1/2"x1/2" cove moulding size to be 2"x2" Asbestos flat eaves ceiling fixed with coves and fillets to local Micro (Eucalyptus Microcoris) timber work. or Balau , Bitis or Kempas. fillet size to be 1 1/2"x1/2" cove moulding size to be 2"x2" 3/4" thick x 6" wide tongued and grooved lunumidella ceiling boards fixed horizontal on 4" x 2" local Micro (Eucalyptus Microcoris)or Balau , Bitis or Kempas. timber joist at every 2'0" c/c. cove moulding size to be 2"x2" Supplying and fixing 6" x 4', 7" x 2', 6" x 3' and 6' x 2' local micro or Balau , Kempas or Bitis timber purling, hip/valley rafters etc. Supplying and fixing 5"x3" purling up to 12'-0" length Balue, Kempas , Micro. Supplying and fixing 4"x3" wall plates up to 12'-0" length, Balue, Kempas, Micro. Supplying and fixing 5" x 3" x 5"2" x 4" x 3" local Micro (Eucalyptus Microcoris) Balau , Bitis , Kempas timber purlins,wall plates, rafters etc. Supplying and fixing 4"x2" local Micro (Eucalyptus Microcoris) or Balau Kempas or Bitis timber purling, rafters etc. Supplying and fixing 2"x2" local Micro (Eucalyptus Microcoris) or Balau, Kempas or Bitis timber bearers. Supplying and fixing 2"x1" local micro (Eucalyptus Microcoris)or Balau, Kempas or Bitis. timber reapers Timber valance/barge board in GINISAPU timber size 9" x3/4" thick fixed to roof frame with brass screws. Sqr. 20450.00

Q18

Sqr.

13700.00

Q19

Sqr.

16575.00

Q20

Sqr.

13120.00

Q21

Sqrs.

19170.00

Q22

Cu.ft.

5150.00

Q23 Q24 Q25

L.ft L.ft Cu.ft.

325.00 260.00 3800.00

Q26

L.ft.

195.00

Q27

L.ft.

86.00

Q28 Q29

L.ft. L.ft.

50.00 165.00

Q30 Q31 Q32

Pressure treatment of timber at an approved kiln including transport charges Applying two coats of wood preservative (Clear) to wood work. Supply and fixing 3/4"x 1/4"x12" long flat iron bracket for fixing valance board/barge board R - GUTTERS AND DOWN PIPES Note: P.V.C. eaves gutter 4 1/2" square type fixed to valance board with P.V.C. brackets at 1'6" c/c including necessary specials. P.V.C. down pipes 3 1/2" dia. fixed to wall with PVC clips at 4'-0" c/c including necessary specials. S - SANITARY FITTINGS Note : 1 In view of the variety of sanitary ware and fittings available in the market, it has become necessary to prescribe the exact quality requirements in terms of performance and durability aspects. The "TOTO" brand and respective model numbers have been chosen as a bench mark to establish the said requirements.

Cu.ft. Sqrs. No.

390.00 470.00 150.00

R01

L.ft.

135.00

R02

L.ft

125.00

2 The brand name and model number appearing in the respective BSR items are purely meant to describe the performance standard of the said fitting/item and does not imply in any model that only the "TOTO" brand is recommended or considered to be restricted to the "TOTO" brand. 3 Any other make/brand that has equivalent performance characteristics are considered as equivalent provided such fittings met with following criteria. (a) (b) (c) (d) (e) (f) has an authorized local agent in Sri Lanka The local agent has been in the trade of the offered make for not less than 5 years. The offered sanitary fitting has a 10 Year manufacturer's warranty issued by the agent. The cistern mechanism shall have an assurance for the availability of spares for the next 3 years. The fittings are manufactured in conformity to BS, JIS, A.S.T.M., A.S. or S.L.S. standards. The dimensions are and performance characteristics are in par with the stated model.

The brands that may be considered as equivalent are "Ideal" brand, or "American standard" or any other approved make which prior approval to be obtained. S01 Supply and fix white ceramic wash basin and pedestal of "TOTO" brand, model LW 236CJ/LW 239 FJ or approved equivalent complete to working order inclusive of : TOTO brand model No. T 205 Chromium plated tap or approved equivalent. Brass Chromium plated "P" trap of "TOTO" brand, model THX-1A3N or approved equivalent. Supply and fix wall hinge white ceramic wash basin on iron brackets; "TOTO" brand model L34 or approved equivalent complete to working order including fixing to the iron wall brackets. (Rate without pillar tap and bottle trap). No. 18465.00

(a) (b) S02

No.

5485.00

S03

S04

S05

S06 S07 S08

Supplying and fixing 11/ 4" (40 mm) dia Bottle 'P' Trap. No. Note : 1 In case where wash basin outlet directly falls on to an open drain, the bottle trap may be omitted. 2 For wash basins fixed on open areas plastic tap of item P08 be specified. Supply and fix Chromium plated tap of "TOTO" brand model No. No. T-205 or approved equivalent with 3 year written warranty from the authorized agent. Supply and fix brass Chromium plated "P" trap of 1 1/4" No. dia. "TOTO" brand model THX-1A-3N or approved equivalent. Supply and fix squatting pan with foot rest "TOTO" brand No. model CE-6 or approved equivalent. Supply and fix ceramic cistern of "TOTO" brand model No. or approved equivalent. Supply and fix close couple dual flush ceramic water closet (6- No. 3 Liters) of "TOTO" brand model CW 660 PJ, SW660J or approved equivalent complete to working order. Supply and fix hand held bidet spray of ABS plastic "TOTO" No. brand model THX 20 NP1V or approved equivalent. Supply and fix Brass Chromium plated 1/2" dia. stop valve of No. "TOTO" brand model TL 511C1 or approved equivalent. Supply and fix Chromium plated adjustable shower bar of "TOTO" brand model TX721AN or approved equivalent. No.

1370.00

3775.00

3790.00

6145.00 8545.00 21250.00

S09

3350.00

S10

2700.00

S11

6460.00

S12

S13 S14

Supply and fix telephone shower of ABS plastic, 5'-0" long No. flexible hose of "TOTO" brand model THX 18N or approved equivalent. Supply and fix brass chromium plated soap tray of "TOTO" No. brand model TX2BV1 or approved equivalent. Supply and fix brass chromium plated single towel bar of No. 600mm "TOTO" brand, model TX5B or approved equivalent. Supply and fix brass chromium plated toilet paper holder of "TOTO" brand, model TS116R or approved equivalent. Supply and fix brass chromium plated towel ring of "TOTO" brand, model TS115S or approved equivalent. Supply and fix brass chromium plated double swivel type towel bar 450 mm of "TOTO" brand model TX725AC. Supply and fix brass chromium plated towel shelf of "TOTO" brand, model TX4A or approved equivalent. Supply and fix automatic hand dryer of "TOTO" brand, model HD 1000 or approved equivalent including electrical connection. Supply and fix brass chromium plated elbow operated tap for the operating theatres of "TOTO" brand, model T23BQ13 or approved equivalent complete to working order. No. No. No. No. No.

4235.00

3900.00 7700.00

S15 S16 S17 S18 S19

4730.00 3060.00 9200.00 9770.00 16385.00

S20

No.

6500.00

S21

Supply and fix wall hung ceramic corner wash basin of size No. 600 x 450 mm of "TOTO" brand, model LW7CJ or approved equivalent complete to working order. Rate inclusive of brackets and connection to pipe line, but without tap and bottle trap. Supply and fix ceramic wall hung wash basin for disabled of "TOTO" brand, model LW103 JT1 or approved equivalent. Supply and fix ceramic urinal with flush valve of "TOTO" brand model U104 or approved equivalent complete to working order. Supply and fix ceramic urinal partition 100 x 350 x 760 mm of "TOTO" brand, model A/100 or approved equivalent. Supply and fix sensor for urinals of "TOTO" brand, model TEA99DV1 or approved equivalent. Supply and fix laboratory sink of 505 x 505 mm with steel pedestal of "TOTO" brand, model LW640CJ and TX812L or approved equivalent. Supply and fix mirror of size 450 x 600 mm of "TOTO" brand, model TX719 AW or approved equivalent. Supply and fix floor drain of square flange of 115 x 115 mm of cast iron with stainless steel TX9BN openable lid of "TOTO" brand or approved equivalent. No.

9100.00

S22

29195.00

S23

No.

10170.00

S24 S25 S26

No. No. No.

14565.00 67830.00 45750.00

S27 S28

No. No.

9990.00 6445.00

S29

S30

S31

Closet squatting square type cum foot rest with trap supplied No. and fixed including flush pipe laid on concrete base. (Indian make) Bowl type glazed ceramic urinal Lanka Ceramic Ltd No. manufactured or equivalent with trap fixed to wall as directed with inlet and outlet connection. Stainless steel kitchen sink of 'TECCA" brand or approved No. equivalent single bowl and single drain board including 12mm heavy duty chromium plated swan tap of 'Grohe" or "Pegler" brand and water connection. Waste water connection with flexible hose chain and PVC bottle trap (bottle trap measured as per item T126) All complete to working order. Mirror bevelled rectangular 20"x 15" with hard wood back 3/4" thickness finished with 2 coats of enamel paint. Aluminium clips and key hole hanging plate including glass shelves. Shower rose 6" P.V.C. fixed vertically with 1/2" valve socket including water connection. Shower rose chromium plated 6" dia. Fixed vertically with 1/2" valve socket including water connection. Supply and fixing plastic seat cover Adjustable shower heads with flexible cords. Make Grohe or equivalent to approval. Supply and install angle valve 12mm dia. chromium plated. Make "Plumber" or equivalent to approval. Bib tap of 12mm dia. chromium plated. Make Grohe or equivalent to approval Supplying and fixing 1/2" bib tap (as per Manufacturer's specification) High-level plastic cistern 9 liters capacity supplied and fixed to wall rawl plug & screws complete with P.V.C. flush pipe, stop cock, water supply connection etc. (Malaysian make) No.

3100.00

3730.00

13000.00

S32

1450.00

S33 S34 S35 S36 S37 S38 S39 S40

No. No. No No. No. No. No. No.

250.00 280.00 800.00 8250.00 1120.00 1955.00 800.00 3400.00

T - PLUMBING Note: All P.V.C. pipes should confirm to S.L.S. 147 T01 T02 T03 T04 T05 Supplying laying and/or fixing 1/2" dia. P.V.C. pipes TYPE 1000 (Specials paid separately). -Do-Do-Do-Do-Do-Do-Do-Do3/4" 1" 1 1/4" 1 1/2" dia. -dodia. -Dodia. -Dodia. -DoL.ft. L.ft. L.ft. L.ft. L.ft. 42.00 58.00 59.00 86.00 123.00

T06 T07 T08 T09 T10 T11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 T23 T24 T25 T26

-Do-Do2" dia. -DoSupplying and fixing 1/2" brass bib tap. (Heavy duty) Supplying and fixing 1/2" bib tap " Water-tech" (as per Manufacturer's specification) Supplying and fixing 1/2" stop cock. Supplying and fixing 3/4" stop cock. Supplying and fixing 1" wheel valve. Supplying and fixing 1 1/2" wheel valve. Supplying and fixing 1/2" Handle valve Supply and install angle valve 12mm dia. chromium plated. Make "Plumber" or equivalent to approval. Bib tap of 12mm dia. chromium plated. Make Grohe or equivalent to approval Adjustable shower heads with flexible cords. Make Grohe or equivalent to approval. Supplying and fixing cormium plated 1/2" angle valve tap with necessary specials Supplying and fixing 3/4" Handle valve Supplying and laying 4" dia. sewer pipes (type 600) Including cement concrete hunching 1:3:6: ( 1") Supplying and laying 6" dia. PVC. sewer pipes (type 600) fixed to wall and floor slab with clips. Supplying and Fixing 1 1/4" dia PVC. waist pipe (type 600) Supplying and fixing 1 1/2" dia PVC. waist pipe (type 600) Supplying and fixing 2" dia. PVC waist pipe (type 600) Supplying and fixing "Plastishell" water tank 500 Ltr. capacity (fittings paid separately). Supplying and fixing "Plastishell" water tank 1000 Ltr. capacity (fittings paid separately). Supplying and installing 2000 ltr. "pastiche" or fiber glass water tank at average 12 ft. height including transporting and hoisting in position Construction of a 12ft. height R.C.C. trestle to lay a 2000 ltr. water tank. (Water tank measured separately as per item T26 ) Construction of a 12ft. height Steel trestle to lay a 2000 ltr. water tank (Water tank measured separately as per item T26) Supplying and fixing 1/2" dia PVC Socket Supplying and fixing 1/2" dia. PVC Valve Socket Supplying and fixing 1/2" dia. PVC Faucet Socket Supplying and fixing 1/2" dia. PVC Elbow Supplying and fixing 1/2" dia. PVC Equal Tee

L.ft. No. No. No. No. No. No. No. No. No. No. No. No. L.ft. L.ft. L.ft. L.ft. L.ft. No. No. No.

177.00 690.00 660.00 170.00 175.00 310.00 400.00 380.00 1130.00 2200.00 8990.00 600.00 440.00 595.00 648.00 90.00 105.00 125.00 6700.00 15700.00 18600.00

T27

No.

48840.00

T28

No.

36405.00

T29 T30 T31 T32 T33

No. No. No. No. No.

37.00 24.00 23.00 33.00 50.00

T34 T35 T36 T37 T38 T39 T40 T41 T42 T43 T44 T45 T46 T47 T48 T49 T50 T51 T52 T53 T54 T55 T56 T57 T58 T59 T60 T61 T62 T63 T64 T65 T66 T67 T68 T69 T70 T71 T72

Supplying and fixing 1/2" dia. PVC Clips Supplying and fixing 3/4" dia. PVC Socket Supplying and fixing 3/4" dia. valve socket Supplying and fixing 3/4" dia. PVC Elbow Supplying and fixing 3/4" dia. PVC Equal Tee Supplying and fixing 3/4" dia. PVC Clips Supplying and fixing 1" dia. PVC Socket Supplying and fixing 1" dia. PVC Valve Socket Supplying and fixing 1" dia. PVC Elbow Supplying and fixing 1" dia. PVC Equal Tee. Supplying and fixing 1" dia. PVC Clips Supplying and fixing 1 1/4' dia. PVC Socket Supplying and fixing 1 1/4" dia. PVC Faucet Socket Supplying and fixing 11/4" dia. PVC Elbow Supplying and fixing 11/4' dia. PVC Equal Tee Supplying and fixing 11/4" dia. PVC Clips Supplying and fixing 11/2" dia. PVC Socket Supplying and fixing 1 1/2" dia. PVC Valve Socket Supplying and fixing 11/2" dia. PVC Faucet Socket Supplying and fixing 1 1/2" dia. PVC Elbow Supplying and fixing 1 1/2" dia. PVC Equal Tee Supplying and fixing 1 1/2" dia. PVC Bend Supplying and fixing 1 1/2" dia. PVC Clips Supplying and fixing 2" dia. PVC Socket Supplying and fixing 2" dia. PVC Elbow Supplying and fixing 2" dia PVC Equal Tee. Supplying and fixing 2" dia. PVC Bend Supplying and fixing 2" dia. PVC Clips Supplying and fixing 2" - 1/1/2" dia. PVC. Re. Socket Supplying and fixing 1 1/2"-11/4" dia. PVC Re. Socket Supplying and fixing 1 1/2" - 1" -doSupplying and fixing 11/4"-1" dia. PVC Re. Socket Supplying and fixing 1"-3/4" dia. PVC Re. Socket Supplying and fixing 1"-1/2" dia. PVC Re. Socket Supplying and fixing 1 1/2"-1/2" dia. PVC Re. Socket Supplying and fixing 1 1/4"-3/4" -doSupplying and fixing 1 1/2"-3/4" -doSupplying and fixing 2"-1/2" -doSupplying and fixing 2"-1/4" -do-

No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No.

30.00 42.00 30.00 45.00 75.00 10.00 53.00 30.00 58.00 95.00 9.00 66.00 43.00 77.00 120.00 10.00 109.00 68.00 75.00 138.00 213.00 189.00 12.00 152.00 195.00 285.00 350.00 12.00 115.00 90.00 75.00 70.00 50.00 45.00 73.00 65.00 78.00 100.00 110.00

T73 T74 T75 T76 T77 T78 T79 T80 T81 T82 T83 T84 T85 T86 T87 T88 T89 T90 T91 T92 T93 T94 T95 T96 T97 T98 T99 T100 T101 T102 T103 T104 T105 T106 T107 T108 T109 T110 T111 T112 T113 T114 T115 T116

Supplying and fixing 2"-1" -doSupplying and fixing 2"-1 1/4" -doSupplying and fixing 3/4"-1/2" dia. PVC Re. Tee. Supplying and fixing 1"-1/2" dia PVC Re. Tee. Supplying and fixing 1"-3/4" dia. PVC Re. Tee. Supplying and fixing 1 1/4"-1/2" dia. PVC Re. Tee Supplying and fixing 1 1/4'-1" dia. PVC Re. Tee Supplying and fixing 1 1/4" - 3/4' -doSupplying and fixing 1 1/2" -1/2" dia. PVC. Re. Tee. Supplying and fixing 1 1/2"-3/4" -doSupplying and fixing 1 1/2"-3/4" -doSupplying and fixing 1 1/2"-1 1/4' -d0Supplying and fixing 2"-1/2"-doSupplying and fixing 2"- 3/4" dia. -doSupplying and fixing 2"-1" dia. -doSupplying and fixing 2"- 1 1/4' dia. -doSupplying and fixing 3/4"-1/2" Re. Forcet tee Supplying and fixing 1'-1/2" -doSupplying and fixing 1"-3/4" -doSupplying and fixing 3/4"-1/2" Re. Elbow Supplying and fixing 1'-1/2" Re elbow Supplying and fixing 1'-3/4" Re. Elbow Supplying and fixing 1/2" dia. bend Supplying and fixing 3/4" -doSupplying and fixing 1" -doSupplying and fixing 1 1/4" -doSupplying and fixing 1 1/2" -doSupplying and fixing 2" -doSupplying and fixing 2 1/2 " -doSupplying and fixing 3" -doSupplying and fixing 4" -doSupplying and fixing 2 1/2" dia PVC sockets Supplying and fixing 3' -doSupplying and fixing 4" -doSupplying and fixing 2 1/2" dia. PVC Valve Sockets Supplying and fixing 3" -doSupplying and fixing 4" -doSupplying and fixing 2 1/2" dia. PVC faucet sockets Supplying and fixing 3" -doSupplying and fixing 4" -doSupplying and fixing 2 1/2" dia. PVC Elbow Supplying and fixing 3" -doSupplying and fixing 4" -doSupplying and fixing 2 1/2" dia. PVC Equal Tee

No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No.

110.00 55.00 60.00 74.00 100.00 90.00 82.00 82.00 125.00 175.00 175.00 200.00 230.00 230.00 230.00 230.00 50.00 55.00 80.00 43.00 54.00 60.00 40.00 50.00 60.00 94.00 210.00 354.00 480.00 1000.00 1370.00 185.00 271.00 380.00 350.00 550.00 750.00 400.00 650.00 1000.00 400.00 620.00 700.00 486.00

T117 T118 T119 T120

Supplying and fixing 3" -doSupplying and fixing 4" -doSupply and fixing 1/2" dia flexible hose - 12" length. Supply and fixing 1/2" dia flexible hose - 18" length. Imported Pipe fittings Note : All imported Pipe fittings shall conform to B.S. Standards and has the Kite mark embossed on the fitting. Supplying and fixing imported (British make or equivalent approved) fittings of the following category.

No. No. No No

780.00 1000.00 415.00 590.00

T121 Supplying and fixing 4" (110 mm) dia double branch. T122 Supplying and fixing 11/4" (40 mm) dia sweep tee 91 deg. T123 Supplying and fixing 4" (110 mm) dia trapped floor gulley. T124 Supplying and fixing 4" (110 mm) dia floor gulley inlet stainless steel. (cover) T125 Supplying and fixing 11/ 4" (40 mm) dia Bottle 'P' Trap. T126 Supplying and fixing 11/2" (110 mm) dia Tubular 'P' Trap. T127 Supplying and fixing 11/2" (50 mm) dia sweep tee135 deg.] T128 Supplying and fixing 11/2" (50 mm) dia double access branch. (with cleaning eye) T129 Supplying and fixing 4" (110 mm) dia access bend. (with cleaning eye) T130 Supplying and fixing 4" (110 mm) dia single branch. (92deg) T131 Supplying and fixing 4" (110 mm) dia single branch. (132 deg) T132 Supplying and fixing 4" (110 mm) dia access branch. 92 deg (with cleaning eye) T133 Supplying and fixing 4" dia. Drainage elbow moulded with cleaning eye (Local make) T134 Supply and fixing 1" dia ball T135 Supply and fixing 3/4" dia ball T136 Supply and fixing 1/2" dia ball U - DRAINAGE

No. No. No. No. No. No. No. No. No. No. No. No. No No No No

6085.00 1000.00 4020.00 6087.00 1335.00 3640.00 1400.00 7230.00 6085.00 3085.00 3485.00 5720.00 850.00 810.00 690.00 630.00

U01

Manhole consists of Grade 15 concrete base of 75mm thickness, 225mm thick brick side walls, Grade 20 concrete cover slab of 75mm thickness, reinforced with Type 2 deformed tor steel bars of 10mm dia. at 150mm c/c both ways. Rate to include for excavation, necessary formwork, lifting hooks and 12mm thick cement sand rendering in 1:3 mix trowel smooth with neat grey cement to all internal surfaces and external exposed surfaces. Manhole internal size of 2'-0"x 2'-0" and depth upto 2'-0" Manhole consists of Grade 15 concrete base of 75mm thickness, 225mm thick brick side walls, Grade 20 concrete cover slab of 75mm thickness, reinforced with Type 2 deformed tor steel bars of 10mm dia. at 150mm c/c both ways. Rate to include for excavation, necessary formwork, lifting hooks and 12mm thick cement sand rendering in 1:3 mix trowel smooth with neat grey cement to all internal surfaces and external exposed surfaces. Manhole internal size of 3'-0"x 3'-0" and depth upto 2'-0" to 3'-0" Manhole consists of Grade 15 concrete base of 75mm thickness, 225mm thick brick side walls, Grade 20 concrete cover slab of 75mm thickness, reinforced with Type 2 deformed tor steel bars of 10mm dia. at 150mm c/c both ways. Rate to include for excavation, necessary formwork, lifting hooks and 12mm thick cement sand rendering in 1:3 mix trowel smooth with neat grey cement to all internal surfaces and external exposed surfaces. Manhole internal size of 4'-6"x 2'-7 1/2" and depth upto 3'-0" to 5'-0"

No.

7450.00

U02

No.

12300.00

U03

No.

41220.00

U04

Construction of brick manhole internal size 4'6"x 2'7 1/2" x 2'6" deep - do - including forming channels. Rate to incolude for RCC Cover slab. Excavation not exceeding 5'0" depth with hard soil. Drawing No. WSS 156.13 & 156.22. Construction of Interceptor Manhole internal size 4'6"x 2'7 1/2"x 5'6" deep - do -. Excavation not exceeding 5'0" depth including working spaces with hard soil - do Construction of Drop manhole internal size 4'6"x 2' 1/2"x 10'0" deep - do -. Excavation exceed 5'0" depth not exceeding 15'0" depth. Drawing No. WSS 169.02.

No.

28655.00

U05

No.

38895.00

U06

58330.00

U07

Manhole consists of Grade 15 concrete base of 75mm thickness,150mm thick RCC side walls r/f with 10mm dia. tor steel work125mm c/c both ways, Grade 20 concrete cover slab of 75mm thickness, reinforced with Type 2 deformed tor steel bars of 10mm dia. at 150mm c/c both ways. Rate to include for excavation, necessary formwork, lifting hooks and 12mm thick cement sand rendering in 1:3 mix trowel smooth with neat grey cement to all internal surfaces and external exposed surfaces. Manhole internal size of 2'-0"x 2'-0" and depth upto 10'-0" Manhole cover 3" thick 2'-0"x2'-0" approx with 1:2:4(3/4") R.C.C. concrete R/F with 10mm dia. torrods @ 4" c/c both ways bottom. Heavy duty cast iron manhole cover 24"x18" supplying and fixing including cover frame. Gully S.W. 4" supplied and fixed including 1:2:4(3/4")concrete gully box. Gulley size 1'-o"x 1'-0" and depth to suit the location, but not exceeding 2'-0", cast in Grade 20 concrete, 75mm thick base slab, wall and cover slab; Cover slab reinforced with 6mm dia. MS rods @ 150mm c/c. Rate to include for necessary excavation, formwork and 20mm thick cement sand 1:3 rendering to all internal and exposed external surfaces, trowel smooth with neat grey cement. Construction of 3'0" dia. soakage pit as per Draw. No.W.S.S. 169.01 in hard ground. Construction of 4'0" dia. soakage pit as per Drw. No.W.S.S. 169.02 in hard ground. Construction of 6'0" dia. Soakage pit in hard soil as per Drawing No. WSS 169.03 Construction of 8'0" dia. Soakage pit in hard soil as per Drawing No. WSS/WP/WS/ TPSP/ 2001/07/01 Construction of 30 persons septic tank as per Drw. No.W.S.S. 174.02 in hard ground Construction of 100 persons septic tank built in brick work chambers as per Drawing No. WP/WS/TPSET/2002/05/01. Construction of 50 Persons Septic tank - do - - do Construction of 150 Persons Septic tank - do - Drawing No. WP/WS/TPSET/2002/03/01 V - ELECTRICAL INSTALLATION. Note: Work shall be done in accordance with specifications for electrical and mechanical works(ICTAD Publication No.SCA/8 of Nov.1987

No.

77000.00

U08

Sq.ft.

400.00

U09 U10 U11

No. No. No.

5840.00 1550.00 2413.00

U12 U13 U14 U15 U16 U17

No. No.

18220.00 24900.00 50000.00

No. No. No.

70000.00 115300.00 198715.00

U18 U19

No. No.

132755.00 238795.00

1

2 3

Internal lighting wiring shall comply with the drawings and shall be in 230/440 volt single core PVC insulated copper cables All switches and socket outlets shall be plated type "Clipsal", " Orange"or Cabtree make. All Fluorescent fittings of gauge 24 GI should be complete with choke (Make:-"Atco","BG" original or -Equivalent) starter and the tube should be Thron, Philips, or Osram All ceiling fans should be KDK, National, Mitsubishi, Hittachi(Original Japan)with guarantee card from the authorized dealer. Rate to include switch boxes, plugs, round or square blocks, Chromium plated M.S. chains, brass hooks, ceiling roses, holders (angle batten and ordinary battens) and any other item necessary. All distribution boards should be incorporated with multi 9 genuine Merlin Gerin, A.B.B. , Hager, F & G , clipsal make MCB's ( Miniature circuit Breaker ) and cabtree, F & G, Clipsal , Merlin Gerin make R.C.C.B.'s (Residual Current circuit Breaker) and Terrasaki, Merlin Gerin, , Dormans Smith ,Biticano , Clockner moeller make M.C.C.B.'s (Moulded Case Circuit Breakers) The whole installation shall be carried out according to CEB/IEE wiring regulations. All the M.C.C.B.'s for the distribution boards should be purchased from the following authorized agents or from their dealers and a certificate or invoice along with their Company seal and Part No., numbers should be produced at the time of payment. Type 1. Merlin Gerin M.C.C.B.'s 2. F & G M.C.B.'s and R.C.C.B.'s 3. Terrasaki M.C.C.B.'s 4. Cabtree R.C.C.B.'s Agent Figaro Ltd. Rotex Ltd. Rotex Ltd. Nawaloka Ltd.

4

5

6

7 8

5. K.I.K. M.C.B.'s K.I.K. Engineers 6.Moeller MCB,MCCB,RCCB Richardson Electrical (Pvt)Ltd. 7. Orange, Switches and Socket outlet OS Projects Pvt Ltd Note The height of the light bracket from floor level is 2.5m Height of the switches from floor level is 1.5m

1 2

3 4

No ceiling fan should be installed at a height of less than 2.7m from floor level The distance of a light source from the wall should be equal to one half the distance between two adjacent light sources and also the distance between light fittings should not exceed 1.5 times the Mounting height. Point wiring only with and including switches (Rate includes wiring from MCB through switch to lamp point and includes the switch, switch box, lamp holder wire and conduit)

V01

Light point wired through a 5Amp one gang one way plate per point switch using 2x1/1.13(2x1/044) P.V.C. insulated copper wire in fully concealed/surface P.V.C. conduits. Light points wired through a 5 Amp two gang one way plate per point switch using 2x1/1.13 (2x1/044) P.V.C. insulated copper wire in fully concealed/surface P.V.C. conduits Light points wired through a 5 Amp three gang one way plate switch using -dittoLight points wired through a 5 Amp four gang one way plate switch using -dittoLight points-wired through a 5Amp 5 gang one way plate switch using - ditto Light points-wired through a 5Amp 6 gang one way plate switch using -dittoLight point wired through a 5Amp one gang two way plate switch using -dittoLight point wired through a 5 Amp one gang one way plate switch using 2x1/1.13(2x1/044) P.V.C. insulated copper wire in fully surface plastic casing and capping Light points wired through a 5 Amp two gang one way plate switch using -dittoLight points wired through a 5 Amp three gang one way plate switch using -dittoLight points wired through a 5 Amp four gang one way plate switch using -dittoLight points wired through a 5 Amp. 5 gang one way plate switch using -dittoLight points wired through a 5 Amp. 6 gang one way plate switch using -dittoLight point wired through a 5Amp one gang two way plate switch using -dittoper point per point per point per point per point per point

1115.00

V02

1675.00

V03 V04 V05 V06 V07 V08

2235.00 2780.00 3330.00

nil
1245.00 1740.00

V09 V10 V11 V12 V13 V14

per point per point per point per point per point per point

2300.00 2860.00 3425.00 3960.00 nil 2500.00

V15

Light point wired through a 5 Amp one gang one way plate per point switch using 2x1/1.13 ( 2x1/044)P.V.C. insulated copper wire in half surface with plastic casing and capping and other half in open air. Light points wired through a 5 Amp two gang one way using dittoLight points wired through a 5 Amp three gang one way using -dittoLight points wired through a 5 Amp four gang one way plate switch using -dittoLight points wired through a 5 Amp. five gang one way plate switch using -dittoLight points wired through a 5 Amp. Six gang one way plate switch using -dittoLight point wired through a 5Amp one gang two way plate switch using -dittoElectric Bell with Bell press switch using 2x1/1.13mm (2x1.044 PVC/insulated copper wire in fully concealed/surface PVC conduits. Electric Bell with bell press switch using flexible wire (twisted twin wire) only in the table legs and floor crossings. 5 Amp Switch socket outlet wired using 2x1/1.13 P.V.C. insulated copper wire & 1x7/0.67(7/029)copper earth wire in fully concealed/surface P.V.C. conduits. 5 Amp Switch socket outlet wired using -ditto- in fully surface plastic casing and capping. 15 Amp switch socket outlet wired using -ditto- in fully concealed/surface P.V.C. conduits. 15 Amp switch socket outlet wired using 2x7/0.67(2x7/029)insulated copper wire & 1x7/0.67 copper earth wire in surface plastic casing and capping. Flush mounted 13 Amp. non-reversible type square pin switched socket outlets wired in ring circuit using 4x1x7/0.67 PVC insulated copper wire and 2x7/0.67 PVC insulated copper earth wire in casing and capping. R = 360/= x L+255/= x N per point per point per point per point per point per point No.

1515.00

V16 V17 V18 V19 V20 V21 V22

2010.00 2575.00 3135.00 3700.00

nil
2500.00 1875.00

V23

1920.00

V24

No.

1725.00

V25 V26 V27

No. No. No.

2205.00 2290.00 2500.00

V28

No.

Rate as following formula

N (R) Rate per circuit (to be calculated as per formula.
L = Distance from DB to last socket ( in Meter) N = Number of 13 Amp. sockets Fan regulator wired without a switch using 2x1/1.13 mm P.V.C. insulated copper wire 1x7/0.67 P.V.C. insulated copper earth wire in fully concealed/surface P.V.C. conduits.

V29

No.

1640.00

V30

V31 V32

Fan regulator wired through a 5 Amp plate one gang one way switch using .-Ditto- in fully concealed/surface P.V.C.conduits. Fan regulator wired without a switch using -ditto- in fully surface plastic casing and capping Fan regulator wired through a 5 Amp plate one gang one way switch using -ditto- in fully surface plastic casing and capping Fan regulator wired without a switch using -ditto- in half surface with plastic casing and copping and other half in open area. Fan regulator wired through a 5 Amp plate one gang one way switch using -dittoFan regulator wired without a 5Amp plate two gang one way switch using -ditto- in fully concealed/ surface PVC conduit Fan regulator wired without a 5Amp plate three gang one way switch using -ditto- in fully concealed/ surface PVC conduit Supply install and wiring the following (Rate includes wiring from MCB through switch and regulator to the fan point and includes the cost of fan)

No.

1730.00

No. No.

2025.00 2170.00

V33

No.

2315.00

V34 V35

No. no

1970.00 3595.00

V36

no

4975.00

V37

Supply and install a electrical fan and fan regulator wired through a 5Amp plate one gang one way switch using - ditto in fully concealed surface P.V.C. conduit Supply and install a electrical fan and fan regulator wired through a 5Amp plate one gang one way switch using - ditto in fully concealed surface P.V.C. conduit casing and capping Supply and install a electrical fan and fan regulator wired through a 5Amp plate one gang one way switch using - ditto in fully surface with plastic casing and capping and other half in open area Supply & Install only the following fillings. Decorative ceiling lamp (Osram Dulux Carrel or approved equivalent) Bracket lamp of gold plated base and transparent cover. Bracket lamp with batton holder including bulbs Pendent Lamp Spot light (equivalent to Osram Halospot)

No.

7690.00

V38

No.

7730.00

V39

No.

7580.00

V40 V41 V42 V43 V44

No. No. No. No. No.

2150.00 2400.00 465.00 455.00 2275.00

V45 V46 V47 V48

Water tight weather proof lamp (equivalent to Osram Dulux Brik) Mercury Vapour Lamp bracket complete 125 watts with clamps (equivalent to Siemens SNA 395) -Ditto- 250 watts (equivalent to Siemens SNA 395) Ceiling fan 56" Sweep (KDK,National,Mitsubishi,Hittachi of Japanese origin) Dimmer type fan regulator with a switch (Clipsal, KDK or equivalent) Exhaust or blower fan 12" dia. (K.D.K. or Equivalent ) Wall mounted fan (K.D.K. or Equivalent )

No. No. No. No.

2500.00 7690.00 14420.00 6200.00

V49 V50 V51

No No. No.

590.00 10410.00 10445.00

Note:
In all fluorescent lamp complete fittings incorporating, choke-Atco, BG and starter, Bulb-Philips, Osram, Thorn Choke-Atco, Starter - BG and Bulbs - Philips, osram, Thorn V52 V53 V54 V55 V56 V57 V58 V59 V60 V61 V62 V63 V64 V65 V66 V67 V68 V69 V70 4-0" long x40W single fluorescent lamp suspension, reflector type. .-Ditto- Box type .-Ditto- Diffuser type 4' -0" longx40W Twin fluorescent lamp suspension, powder coated reflector type. .-Ditto- Box type .-Ditto- Diffuser type 2x20W single fluorescent lamp suspension, powder coated reflector type .-Ditto- Box type .-Ditto- Diffuser type 2'-0" longx20W Twin fluorescent lamp suspension powder coated Reflector type .-Ditto- Box type .-Ditto- Diffuser type 4'-0" longx20W single fluorescent lamp Batten, powder coated Reflector type .-Ditto- Box type .-Ditto- Diffuser type 4'-0" longx20W Twin Fluorescent lamp Batten, powder coated Reflector type .-Ditto- Box type .-Ditto- Diffuser type 2"x40W single fluorescent lamp Batten powder coated Reflector type No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. 1000.00 1000.00 1150.00 1500.00 1500.00 2050.00 760.00 830.00 995.00 1300.00 1300.00 1550.00 850.00 850.00 1230.00 1300.00 1300.00 1515.00 1175.00

V71 V72 V73 V74 V75 V76

V77 V78 V79 V80 V81

.-Ditto- Box type .-Ditto- Diffuser type 2'-0" longx40W Twin fluorescent lamp Batten powder coated Reflector type .-Ditto- Box type .-Ditto- Diffuser type 4-8 ways SP&N Distribution Board with thermo plastic frame and door, earth and neutral bars din trail type (protection rating IP40) 8-10 ways SP&N Distribution board with -ditto10-12 ways SP&N Distribution board with -ditto14-16 ways SP&N distribution board with -ditto16-19 ways SP&N Distribution board with -dittoProvide an earth electrode copper plate 2'-0"x2'-0"x1/8" in 3m deep. Rate to include connection to the main panel, sub main, earth clips, excavation etc. with 1'-0"x 1'-0"x 1'-0" earth pit including 4 1/2" brick work and 3" concrete slab. Provide an earth electrode 2" dia 6'0" long G.I. pipe -dittowith 1'-0"x 1'-0"x 1'-0" earth pit including 4 1/2" brick work and 3" concrete slab. Supplying and wiring 2 x 2.5mm2 (7/.029") PVC/PVC/Cu cable + 2.5mm2 (7/.029) earth wire to working order excluding conduit. Supplying and wiring 2 x 6mm2 (7/.044") PVC/PVC/ Cu cable + 6mm2 (7/.044") earth wire complete to working order excluding conduit/casing Supplying and wiring 2 x 6mm2 (7/.044") PVC/PVC/ Cu cable complete to working order excluding conduit/casing Supplying and wiring 4 x 6mm2 (7/.044") PVC/PVC/ Cu cable + 6mm2 (7/.044") earth wire complete to working order excluding conduit/casing Supplying and wiring 2 x 10mm2 (7/.052") PVC/PVC/ Cu cable + 10mm2 (7/.052") earth wire complete to working order excluding conduit/casing Supplying and wiring 4 x 10mm2 (7/.052") PVC/PVC/ Cu cable + 10mm2 (7/.052") earth wire complete to working order excluding conduit/casing Supplying and wiring 2 x 16mm2 (7/.064") PVC/PVC/ Cu cable + 16mm2 (7/.064") earth wire complete to working order excluding conduit/casing

No. No. No. No. No. No.

1175.00 1690.00 1380.00 1380.00 1590.00 1420.00

No. No. No. No. Item

1420.00 1610.00 1825.00 1825.00 17040.00

V82

Item

1470.00

V83

L.ft.

50.00

V84

L.ft.

118.00

V85

L.ft.

91.00

V86

L.ft.

183.00

V87

L.ft.

165.00

V88

L.ft.

274.00

V89

L.ft.

237.00

V90

Supplying and wiring 4 x 16mm2 (7/0.064") PVC/PVC/ Cu cable + 16mm2 (7/.064") earth wire complete to working order excluding conduit/casing Supplying and wiring 2 x 25mm2 PVC/PVC/Cu cable + 16 mm2 earth wire complete to working order excluding conduit/casing. Supplying and wiring 4 x 25mm2 PVC/PVC/Cu cable + 16 mm2 earth wire complete to working order excluding conduit/casing. Supplying and wiring 4 x 95mm2 PVC/PVC/Cu cable + 50 mm2 earth wire complete to working order excluding conduit/casing. Supplying and fixing 2 core flexible (0.5mm2) - do Supplying and wiring 2.5mm2 (7/.029") earth wire complete to working order excluding conduit/casing. Supplying and wiring 6 mm2 (7/.044") earth wire complete to working order excluding conduit/casing. Supplying and wiring 10 mm2 (7/.052") earth wire complete to working order excluding conduit/casing. Supplying and wiring 16 mm2 (7/.064") earth wire complete to working order excluding conduit/casing. Supplying and wiring 1mm2 (1/.044") PVC/PVC/ Cu two wire complete to working order excluding conduit/casing.

L.ft.

401.00

V91

L.ft.

332.00

V92

L.ft.

564.00

V93

L.ft.

1808.00

V94 V95 V96 V97 V98 V99

L.ft. L.ft. L.ft. L.ft. L.ft. L.ft.

14.00 12.00 27.00 47.00 88.00 11.00

V100 Supplying and wiring 2.5mm2 ((7/.029") PVC/PVC Cu two wire complete to working order excluding conduit/casing. V101 Supplying and wiring with 4mm2 (7/.036") PVC/PVC/Cu two wire complete to working order excluding conduit/casing. V102 Supplying and wiring with 2* 4mm2 (7/.036") PVC/PVC/Cu cable+4mm2(7/.036) earth wire complete to working order excluding conduit/casing. V103 Supplying and wiring with4* 4mm2 (7/.036") PVC/PVC/Cu cable+4mm2(7/.036) earth wire complete to working order excluding conduit/casing. V104 Supplying and wiring with 2* 2.5mm2 (7/.029") PVC/PVC/Cu cable+2.5mm2(7/.036) earth wire complete to working order excluding conduit/casing. Note: Supply, install and wire with enclosure the following makes :

L.ft.

27.00

L.ft.

34.00

L.ft.

80.00

L.ft.

135.00

L.ft.

55.00

Cabtree, F & G, Genuine, Merlin & Gerin, Terrasaki,. V105 25Amp(30 mA) SP&N (Single Phase & Neutral) RCCB V106 V107 V108 V109 V110 V111 V112 V113 V114 V115 V116 V117 V118 V119 V120 V121 V122 V123 V124 25Amp(100 mA) SP&N RCCB 40Amp(30 mA) SP&N RCCB 40Amp(100 mA) SP&N RCCB 60Amp(30 mA) SP&N RCCB 60Amp(100 mA) SP&N RCCB 25Amp(30 mA) TP&N (Three Phase & Neutral) RCCB 25Amp(100 mA) TP&N RCCB 40Amp(30 mA) TP&N RCCB 40Amp(100 mA) TP&N RCCB 60Amp(30 mA) TP&N RCCB 60Amp(100 mA) TP&N RCCB Main switch 30 Amp SP&N MCB SP (Single Pole) 6-40 Amp MCB SP 50-100 Amp MCB DP (Double Pole) 6-40 Amp MCB DP 50-100 Amp MCB TP ( Three Pole) 6-40 Amp MCB TP 50-100 Amp 30,40,60,100 Amp Three pole MCCB with metal enclosure No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. deleted deleted 3215.00 3475.00 4675.00 5800.00 deleted deleted 4590.00 4590.00 7945.00 7955.00 1245.00 737.00 3530.00 1730.00 1775.00 3650.00 4085.00 10060.00 11600.00 9215.00 10100.00 4950.00 8840.00 127.00 2255.00 3050.00 5130.00 1680.00 L.ft. L.ft. L.ft. 12.00 10.00 13.00

V125 30,40,60,100 Amp four pole MCCB (25KA) with metal enclosure V126 30,40,60,100Amp Three pole MCCB without enclosure V127 30,40,60,100Amp Three pole MCCB (25 Ka) without enclosure V128 30 Amp TP&N main switch V129 60 Amp TP&N main switch V130 D'Bracket complete set (small size) V131 Supplying and fixing 30 A T.P.N. isolator complete to working order with enclosure. V132 Supplying and fixing 60 A T.P.N. isolator complete to working order with enclosure. V133 Supplying and fixing 100 A T.P.N. isolator complete to working order with enclosure. V134 Supplying and fixing 100 A T.P.N. isolator complete to working order with enclosure. V135 3/4" - 1" PVC conduits laying in the slab including placing binding wire to draw through conduits. V136 Supplying and fixing 5/8" PVC conduit including clips. V137 Supplying and fixing 3/4" PVC conduit including clips.

V138 Supplying and fixing 1" PVC conduit including clips. V139 Supplying and fixing 3" dia. PVC type 400 pipe including clips. V140 Supplying and fixing 1 1 /2" dia. PVC type 400 pipe including clips. V141 Supplying and fixing 1 1 /4" dia. PVC type 400 pipe including clips. V142 Supplying and fixing 3/4" dia. PVC conduit bend V143 Supplying and fixing 1" dia. PVC conduit bend V144 Supplying and fixing 1 1/2" dia. PVC conduit bend V145 Supplying and fixing 1 1/4" dia. PVC conduit bend V146 Supplying and fixing 2" dia. PVC conduit bend V147 Supplying and fixing 1 1/4" dia. PVC conduit pipe V148 Supplying and fixing 1 1/2" dia. PVC conduit pipe V149 Supplying and fixing 2" dia. PVC conduit pipe V150 Supplying and fixing 1" dia. PVC conduit pipe V151 Supplying and fixing 3/4" or 1" PVC conduit junction box. V152 V153 V154 V155 V156 V157 Supplying and fixing 1" PVC casing Supplying and fixing 1 1/4" PVC casing Supplying and fixing 1 1/2" PVC casing Supplying and fixing 2" PVC casing Supplying and fixing 2"x 2: box casing. PVC casing

L.ft. L.ft. L.ft. L.ft. No. No. No. No. No. L.ft. L.ft. L.ft. L.ft. No. L.ft. L.ft. L.ft. L.ft. L.ft. per Set

14.00 177.00 29.00 22.00 15.00 17.00 38.00 27.00 54.00 31.00 46.00 56.00 12.00 24.00 16.00 20.00 25.00 36.00 65.00 214.00

Supply and install complete "D" shape bracket including insulator, Nuts, bolts ect. fixed to working order.

V158 Supply and install 2"*2"*6mm "L" Iron, including

Per l.ft

220.00

drilling 12mm holes, 10mm G.I. bolt, and application of anticorrosive paint all complete to working order.
V159 Supply and install Recessed type ceiling lights with louvered mirror type, florescent lamp fitting with No. No. No. No. No. No. Lft. 2880.00 3410.00 4530.00 3580.00 5340.00 5985.00 100.00

(a)2'-0"*1'0"-2 no 20 watts fluorescent lamps (b)2'-0"*2'0"4 no 20 watts fluorescent lamps (c)2'-0"*1'0"-4 no 20 watts fluorescent lamps (d)4'-0"*1'0"-2 no 40 watts fluorescent lamps (e)4'-0"*1'0"-3 no 40 watts fluorescent lamps (f)4'-0"*4'0"-4 no 40 watts fluorescent lamps V160 Supply and wiring 2x6mm2(7/044) PVC/PVC/CU Cable complete to working order excluding conduit & casing W - METAL WORK Note: Aluminium doors, windows and partitions shall confirm to the following requirements:

1

Aluminium alloy should confirm to- BS 1474:1972 Surface treatment shall confirm to BS 1615 and BS 3987 Anodized coating thickness should be 15 +/- 5 microns Minimum section thickness 1.8mm door frame , 1.5 mm window frame and 1.00 mm partition. Most of the aluminium extrusions available in the Local Market are being manufactured in Sri Lanka by two leading companies and both companies are changing the extrusion profiles and thicknesses from time to time. Hence it has become very difficult t o specify standard section sizes that are to be used for door /window frames and sash members. Hence the rates given herein are based on the recommended minimum sizes and thicknesses and profiles as per their hand books published by M/S ALUMAX (PVT) LTD and by M/S LANKA ALUMINIUM INDUSTRIES LTD At the same time of bidding, all the Bidders shall specifically be requested to submit the following information. The specifications and thickness of Aluminium extrusions bidder proposes to use on the works. Full size cross sections Documentary evidence from the Profile Manufacture to the effect that the proposed profile will serve for the intended purpose. A Manufacturer's test certificate be produced as evidence that the powder coating is of required thickness. Physical properties :(a) Minimum tensile strength 150 Mpa (b) Elongation 7% All screws should be stainless steel But hinges and bar type hinges should be Aluminium or Stainless Steel. The item descriptions should be read along with the annexed detail drawings. The rates and hence the item description shall include 5mm thick plain or Tinted glass, Neoprene gasket, pop revets, Rawl plugs, Screws, Aluminium cleats etc. The rates given herein are for Bronze Anodized aluminium profiles. For powder coated aluminium profiles (minimum powder coating thickness of 40 + 5 microns) the rates shall be increased by 10%.

2 3 4

5

(a)

(b)
©

(d)

6

7 8

9

For natural aluminium profiles, the rates shall be decreased by 5%. Single Sliding Door W01 Bronze anodized aluminium glazed single sliding door with mid rail and 5mm thick tinted glass panes, neoprene and wool beading, gaskets, flush bolt, threaded bar with nut roller, cup and approved quality lock Double Sliding Door Bronze anodized aluminium glazed double sliding door with mid rail and 5mm thick tinted glass panes, neoprene and wool beading, gaskets, flush bolt, threaded bar with nut roller, cup and approved quality lock Double Sliding Door with Fanlight Bronze anodized aluminium glazed double door with sliding fanlight on top with mid rail and 5mm thick tinted glass panes, neoprene and wool beading, gaskets, flush bolt, threaded bar with nut roller, cup and approved quality door lock, door handle with cap and nut and floor closer. Bronze anodized aluminium glazed double door with sliding fanlight on top with mid rail and 5mm thick tinted glass panes, neoprene and wool beading, gaskets, flush bolt, threaded bar with nut roller, cup and approved quality door lock, door handle with cap and nut without door closer Swing Door Single Sash Butt Hinges Bronze anodized aluminium single sash sliding door with mid rail and 5mm thick tinted glass panes, neoprene and wool beading, gaskets, pop rivots, hreaded bar with nut and approved quality lock, butt hinges, door handle with cap nut. Swing Door Double sash floor Hinge Bronze anodized aluminium double sash (swing type) with mid rail and 5mm thick tinted glass panes, neoprene and wool beading, gaskets, flush bolts, hreaded bar with nut and approved quality lock, butt hinges, door handle with cap nut and floor mounted door closer. Bronze anodized aluminium double sash (swing type) with mid rail and 5mm thick tinted glass panes, neoprene and wool beading, gaskets, flush bolts, hreaded bar with nut and approved quality lock, butt hinges, door handle with cap nut without door closer. Top Fixed Swing Door Double Sash Floor Hinge Sq.ft. 735.00

W02

Sq.ft.

780.00

W03

Sq.ft.

1190.00

W04

Sq.ft.

1000.00

W05

Sq.ft.

950.00

W06

Sq.ft.

2450.00

W07

Sq.ft.

1190.00

W08

Bronze anodized aluminium double sash (swing type) with fixed glass on top, mid rail and 5mm thick tinted glass panes, neoprene and wool beading, gaskets, flush bolts, hreaded bar with nut and approved quality lock, butt hinges, door handle with cap nut and floor mounted door closer. Bronze anodized aluminium double sash (swing type) with fixed glass on top, mid rail and 5mm thick tinted glass panes, neoprene and wool beading, gaskets, flush bolts, hreaded bar with nut and approved quality lock, butt hinges, door handle with cap nut without door closer. Swing Door Single Sash Butt Hinges - Veneered Plywood door

Sq.ft.

2200.00

W09

Sq.ft.

1075.00

W10

Bronze anodized aluminium single sash butt hinges 3mm thick veneered plywood on both side door with mid rail and 5mm thick tinted glass panes, neoprene and wool beading, gaskets, pop rivots, hreaded bar with nut and approved quality lock, butt hinges, door handle with cap nut.

Sq.ft.

960.00

Swing Door Single Sash Butt Hinges Ply Board W11 Bronze anodized aluminium single sash butt hinges 3mm thick ply board both side door with mid rail and 5mm thick tinted glass panes, neoprene and wool beading, gaskets, pop rivots, hreaded bar with nut and approved quality lock, butt hinges, door handle with cap nut. Swing Door Single Sash Butt Hinges Aluminium Sheeting W12 Bronze anodized aluminium single sash butt hinges Aluminium sheeting paneled board door with neoprene and wool beading, gaskets, pop rivots, hreaded bar with nut and approved quality lock, butt hinges, door handle with cap nut. Double Sliding Window with Transom Bronze anodized aluminium double sliding with Transom, consisting of 5mm thick tinted glass and frame. Sliding with Top Fixed Bronze anodized aluminium sliding window with top fixed consisting of 5mm thick glass and lock, roller screws, gaskets, nut felt, pop rivots, cap, plastic guide etc. Double Sliding Window Sq.ft. 975.00 Sq.ft. 1000.00

W13

Sq.ft.

1050.00

W14

Sq.ft.

750.00

W15

Bronze anodized aluminium double sliding window consisting of 5mm thick glass and lock, roller screws, gaskets, wool felt, plastic guide and cap etc. Sliding Window with Top Pivot Bronze anodized aluminium sliding window with top pivot/top hung consisting of 5 mm thick tinted glass and locks, roller screws, gasket wool felt, pop rivots, cap plastic guide, pivot hinge, pivot lock and weather ring etc. Sliding Window with Top Louver Bronze anodized aluminium sliding window with top louvers and 5mm thick glass and aluminium frame with locks, roller, screws, gaskets, wool felt, pop rivots, cap and plastic guide etc. Sliding Window Bronze anodized aluminum sliding window consisting of 5mm thick tinted glass and lock, roller screws, gasket, wool felt, pop rivots, plastic guide and cap etc. Double Sliding Window Bronze anodized aluminum double sliding( 4 track) window consisting of 5mm thick tinted glass and lock, roller screws, gasket, wool felt, pop rivots, plastic guide and cap etc. Casement Window with Sash (Using) Bronze anodized aluminium casement window with sash casement hook, screws, pop rivots, door hinge, weather strip gasket etc. Bronze anodized aluminium casement window with sash divided using casement hook, screws, pop rivots, door hinge, weather strip gasket etc. Casement Window with Top Hung Bronze anodized aluminium casement window with top hung fanlight and complete with casement lock, screws, pop rivots, gaskets, door hinge, weather strip etc. Casement Window with Top Louver Bronze anodized aluminium casement window with top louver consisting of casement lock, screws, pop rivots, gaskets, door hinge, weather strip etc. Fixed Window Bronze anodized aluminium fixed glazed window with 5mm thick tinted glazed and screws, pop rivots, gasket and wool felt etc. Louver Bronze anodized aluminium frame louvers with pop rivots, screws etc. Partition with Glass & Board

Sq.ft.

675.00

W16

Sq.ft.

1210.00

W17

Sq.ft.

refer item no.W18 & W25

W18

Sq.ft.

780.00

W19

Sq.ft.

1035.00

W20

Sq.ft.

850.00

W21

Sq.ft.

970.00

W22

Sq.ft.

1050.00

W23

Sq.ft.

975.00

W24

Sq.ft.

460.00

W25

Sq.ft.

975.00

W26

Bronze anodized partition frame top and bottom 3mm thick ply board both side (total thickness 6mm), 5mm thick tinted glass with pop rivots, gasket and GI channels Partition with Door Bronze anodized aluminium partition or shop front with fully glass (5mm thick tinted) and door single sash hinged type with pop rivots, gasket, wool felt, door handle with cap nut, door lock, butt hinges, GI channels, threaded bar with nuts etc. Bronze anodized aluminiuum with 5mm thick tinted glass on top and 3mm plywood sheet at bottom (total board thickness 6mm t) with single sash hinged type with pop rivots, screws, gasket etc. Shop Front with Door Bronze anodized aluminium shop front with door 5mm thick tinted glass and hinged door with pop rivots, casements, gaskets, wool felt, door handle, cap nut, door lock, floor hinge, threaded bar with nut etc. Shop Front with Glass and board Bronze anodized aluminium shop front with 5mm thick tinted glass on top and 3mm plywood sheet at bottom (total thickness 6mm) with single sash hinged type with pop rivots, casements, gaskets, wool felt, cap nut, threaded bar with nut etc. Curtain Wall with Sash Bronze anodized aluminium curtain wall with 5mm thick tinted glass sash fixed with casement lock, pop rivots, arm pair, gasket, double foam tape etc. Gypsum Board Partition Fabricating and installing gypsum board partitioning with necessary GI channel member frame work fixed on to wall and floors and 1/2" thick gypsum board fixed to both sides of the frame work all completed with board joints taped and finished with gypsum compound to get wall finish. Rate to include for applying one coat of Acrylic filler to boards.

Sq.ft.

515.00

W27

Sq.ft.

635.00

W28

Sq.ft.

680.00

W29

Sq.ft.

1135.00

W30

Sq.ft.

670.00

W31

Sq.ft.

1250.00

W32

Sq.ft.

485.00

W33

Supply, fabricate and install powder coated (color to approval) aluminium partition for cubicles including vertical, horizontal members fixed with suitable expansion type Anchor bolts to RCC column, floor etc. consisting of 12mm thick plywood laminated with coloured high pressured melamine coated board (perstorp or equivalent to approval) on both faces (colour to approval) for bottom panel, 5mm thick clear float glass for middle panel and to top panel to approval (height varies from 7'-0" to 8'-0") complete with suitable gaskets around frames. (Door measured separately). Powder coating thickness + microns.

Sq.ft.

550.00

W34

W35

Door Pull Handle Supplying and fixing 'U' shape stainless steel door pull handle No fixed complete to working order. CEILING Expanded polystyrene panel ceiling system consisting 4'-0"x2'- Sq.ft. 0"x3/4" thick expanded polystyrene ceiling panels, white backed enamel aluminium capped. G.I. T-Section frame work suspended on gage 14 G.I. wire at 4'-0" centers Mineral fiber suspended ceiling system consisting 4'-0"x2'0"x9/16" thick mineral fiber ceiling panels, white backed enamel aluminium . capped G.I. T - Section frame work suspended on gage14 G.I. wires at 4'-0" centers Supply and install mineral fiber Japanese make suspended exposed ceiling system using 2'-0"x 2'-0"x 12mm ceiling slabs in white color interlock type aluminium grid system suspended with gauge 14GI wire to soffit of concrete or timber roof members. Supplying and fixing 10mm thick gypsum board suspended ceiling 2'-0"x 2'-0"x with GI grid system comprising main T bars, hangers etc. Rate to include for making joints and applying one coat filler. IRON GRILL Welded, Diamond shaped Iron grill, consisting 1/4"x3/4" flat iron frame, 1/4" dia M.S. rods at 3" centers to form 3"x6" diamond shape grill Rate shall include for fixing with No.10, 1" counter sunk iron screws and applying two coats of antiCorrosive paint. (Based on 2'-0"x4'-0" area) Sq.ft.

6000.00

Deleted

W36

215.00

W37

Sq.ft.

310.00

W38

Sq.ft.

355.00

W39

Sq.ft.

337.00

W40

Welded Diamond shaped iron grill, consisting 1/4"x3/4" flat iron frame without joints, 1/4"x3/4" mullions without joints, 1/4"x3/4" isolated mid rails, 1/4" dia. M.S. rods welded to form 3"x6" diamond shaped isolated panels. Rate -do(Based on 9'-0"x6'-0" area) Mild steel door 3'-0"x9"-0" high overall with 2'-3" high Iron grill on top consisting 1 1/2"x1 1/2"x4mm thick angle Iron door frame, 1/4" dia. mild steel grill on top (3"x6" diamond shape), 1"x1" M.S. Hollow section outer frame in sash with 2 No. 1"x1"x 3mm thick angle iron mid rail at 3'-0" hight, sheet gage 2.0 G.I. bottom panel, 1/4" dia. mild steel grill on top panel , (3"x6" diamond shape) fix complete with 3No. 4"x4" M-S Butt Hinges tower bolt and Hasp and plate. Rate shall include for applying shall two coats of anti-Corrosive paint. Welded Diamond shaped iron grill, consisting 3/4"x3/4"x 4mm angle iron frame 1/4"x3/4" Mullions at 2'-0" centres.1/4" dia. MS rods welded together to form 3"x6" Diamond shape grill. Rate shall include for fixing with No.10, 1" counter sunk iron screws and applying -do-. MILD STEEL BALUSTRADE

Sq.ft.

290.00

W41

Sq.ft.

375.00

W42

S.ft.

370.00

W43

Mild steel balustrade in stair case consisting 1/4"x1 1/2" flat iron top rail, 2 No. 1/4"x3/4" flat iron side rails welded together with 5/8" dia. M.S. uprights at 1'-0" centers. Rate shall include for making holes and fixed to stair case and applying two coats of anti-Corrosive paint. Fabricate, supply and fix stainless steel pipe hand rail at staircase comprising 1 1/4" dia. uprights at 1'-0" c/c, 2" dia. top rail and 1" dia. middle rail. Uprights fixed to steps with 100 x 100 x 8mm thick S.S. base plate with 8mm dia. S.S. nuts and bolts complete as per working order.

L.ft.

470.00

W44

L.ft.

3700.00

Y01

Y - STRUCTURAL STEEL WORK Supplying and fixing 2"x2"x5mm angle iron purling at maximum spacing of 4'-0" centers upto maximum span of 10'0" including nuts, necessary bolds & washers etc. and application of two coats of Anti-Corrosive paint.

L.ft.

240.00

Y02

Supplying and fixing 2 1/2"x 2 1/2" x 5mm angle iron purling at maximum spacing of 4'-0" centers maximum span of 11'0"(not less than 10'-0") for a asbestos purling roof without covering tiles on top. Rate shall include for necessary nuts, bolds & washers, etc. applying two Anti-Corrosive paint. Supplying and fixing3"x3" x 5mm angle iron purling at maximum spacing of 4'-0" centers maximum span of 12'0"(not less than 11'-0") for a asbestos purling roof without covering tiles on top. Rate shall include necessary nuts, olds & washers etc. , applying two coats of anti -Corrosive paint. Supplying and fixing 4" x 2" x 5mm channel Iron purling including 2 coat of anticorrosive paint up to 14'-0" span at 4'0" c/c Supplying and fixing 5" x 21/2" x 6mm chanel Iron purling to existing Roof frame work , including two coats of anticorrosive paint up to 16'-0" span, at 4'-0" c/c Supplying and fixing 6" x 3" x 1/4" channel Iron -do- up to 18'-0" span at 4'-0"c/c Mild steel Roof truss Mild steel Roof truss (Maximum spacing 10'-0" ),20'-0", span centre to centre, 25 pitch max,18 pitch minimum with 4'-0" wide eaves at both sides, consisting of 2 No. 2"x2"x 5mm angles as top and bottom chords, 1 No. 2"x2"x 5mm angles as struts and ties, 1/4" thick gusset plates, 3/8" thick. base plates, 1/2" dia M.S. Rag bolts, 3"x3"x 5mm size 1'-0" long purling cleats at 3'-6" centers and 2"x2"x 5mm thick spacers at 2'-0" centers. Rate shall include for fabricating, transport, hoisting, fixing in position, and applying two coats of anti corrosive paint. (as per detail drg. No. 1190 school work branch)

L.ft.

273.00

Y03

L.ft.

347.00

Y04

L.ft.

428.00

Y05

L.ft.

798.00

Y06

L.ft

967.00

Y07

No

39000.00

Y 08

Mild steel Roof truss (Maximum spacing 10'-0") 25'-0", span centre - do-

No

45000.00

Y09

Supplying, fabricating and hoisting in position of 9 m (30'-0") span steel roof truss as per Drawing No. 1732 of School Work Division of Ministry of Education comprising of 2 No. 65 x 65 x 6mm double angles as top and bottom welded with M.S. Plate of 65 x 65 x 8mm at 600mm intervals, and web member comprising of double angle of sizes 65 x 65 x 6mm and 50 x 50 x 6mm connected with 8mm thick mild steel gusset plate and 10mm thick base plate of 225 x 225 on either side and 10mm thick vertical gusset plate at the ends. All as per drawing including 02 coats of Zinc Phosphate paint and two coats of enamel paint including hoisting in position. Rate shall include for hoist in position. Steel Scaffolding Supplying and erecting steel scaffolding. Rate to include for dismantling same after completion of work. Zinc Alum Roofing Supplying and fixing zinc aluminium color bond standard ridge cap to existing sheet roof using new fasteners. Supply and fix proprietary coated zinc alum gutter (minimum base metal thickness of sheet 0.4mm and minimum total thickness 0.47mm) complete with end caps, running joints etc.. All joints to be properly connected with an adequate side laps not less than 225mm length and with sealant to ensure water tightness along the entire length of the gutter and including angle iron gutter brackets 25x25x3mm at 450mm centers with an adequate slope as directed and including application of two coats of each anticorrosive paint and enamel paint to all steel surfaces to match the gutter fix in position. Color bonded wall cladding 0.40mm thick fixed to external wall boxed out at down pipes including sills, flashing, removable sections at access points such as cleaning eyes etc. completely covering the surface as directed by the Engineer. Supply and lay aluminium foil heat reflecting material double side and fire proof at underside of roof supported at 2"x 2" mesh. Supply and fix zinc alum profile sheet (minimum base metal thickness of 0.4mm and minimum thickness of 0.47mm laid on existing purling of joints to be properly connected with an adequate side slope and to ensure water tightness along the entire length and complete to working order.

No

65000.00

Y10

Set per day L.ft.

77.00

Y11

305.00

Y12

L.ft.

510.00

Y13

Sq.ft.

235.00

Y14

Sqr.

2390.00

Y15

Sqr.

23530.00

Y15 Y16 Y17 Y18 Z01.

Supply and installation of Galvanize iron "C" channels 125 x 50 x 20 x 2.3mm thick Supply and fixing double angle sleepers size 2" x 2" x 1/4" Supply and fixing double angle sleepers size 21/2" x 21/2" x 1/4" Supply and fixing double angle sleepers size 3x3x1/4 Z-MAINTAINED WORK Demolishing reinforced cement concrete in suspended floors 4" thick , removing reinforcement and clearing debris. Demolishing cement concrete and clearing debris in 6" thick floors. Demolishing reinforced cement, concrete in lintol of 9"x6" removing reinforcement and clearing debris. Demolishing reinforced cement, concrete in lintol of 4 1/2"x6" removing reinforcement and clearing debris.

L.ft. L.ft. L.ft. L.ft. Cube

210.00 570.00 610.00 670.00 14275.00

Z02. Z03 Z04. Z05. Z06. Z07. Z08. Z09. Z10. Z11. Z12. Z13. Z14. Z15 Z16. Z17. Z18. Z19.

Cube L.ft L.ft

6590.00 34.00 28.00 930.00 1130.00 425.00 21.00 550.00 1510.00 100.00 150.00 730.00 1100.00 100.00 150.00 360.00 210.00 38.00

Demolishing brick work in cement , stacking brick and Cube. clearing debris away. Demolishing 9" thick brick in cement" stacking brick and Cube clearing debris away. Demolishing 4 1/2" thick brick in cement stacking brick and Sqr. clearing debris away. Demolishing drains and clearing debris. L.ft Demolishing 3" thick floors brick paved and clearing debris Sqr. away. Demolishing rubble masonry is cement. Stacking rubble and Cube clearing debris Removing and stacking door sash only up to 40 S.ft from No existing walls. Removing and stacking door sash only over 40 S.ft from No existing walls. Removing and stacking door frame size up to 40 S.ft from No existing walls. Removing and stacking door frame size over 40 S.ft from No existing walls. Removing and stacking window sash only up to 40 S.ft from No existing walls. Removing and stacking window sash only over 40 S.ft from No existing walls. Existing door or window frames renewing in short lengths L.ft with class I timber. Removing damage sashes for door or window and preparing Per sash and re-fixing. Removing and stacking glass panes in doors and windows and S.ft fanlight.

Z20.

Door or window frame altering existing rebate fillet using class I timber with screws and fixing available sashes. Removing ceiling asbestos including timber frame work, stacking serviceable materials and clearing debris away in single storied building. Removing ceiling asbestos including timber frame work, stacking serviceable materiel and clearing debris away in two storied building. Removing ceiling timber frame work, (asbestos sheet not available) stacking serviceable materiel and clearing debris away in single storied buildings. Removing ceiling timber frame work, serviceable materiel and clearing debris away in two storied buildings. Beading , Halmilla 1 1/2" by 1/ 2" thick plain chamfering supplying and fixing complete with brass screws. Removing and stacking valance, Barge board materials and clearing debris away in single storied building. Removing and stacking valance , Barge board materials and clearing debris away in two storied building. Removing and stacking trellis work Trelling work with 1/2"x1/2" laths fixing 2" apart diagonally, horizontally or vertically on existing timber framing. Door or window easing only Boards, barge, Valance, fascia available, fixing including cutting and minor repairs. Removing and stacking tile calicut or half round from roof of single storied building. Removing and Stacking tile Calicut or half round from 2 Storied building. Removing and stacking calicut type ridge tile. Removing and stacking corrugated asbestos sheet from roof of single storied building. Removing and stacking corrugated asbestos sheet from roof of two storied building. Removing and stacking corrugated asbestos sheet from roof of three storied building. Reapers , available fixing with wire nails. Timber available, sorted out cur to required size and fixing in roof and other carpentry work. Ridging (available of site) tiles bedded in lime cement motor 1:1:4 and coloured to match tiles.

No

180.00

Z21.

Sqr.

870.00

Z22.

Sqr.

1245.00

Z23.

Sqr.

150.00

Z24.

Sqr.

190.00

Z25. Z26. Z27. Z28. Z29.

L.ft L.ft L.ft Sqr. S.ft

58.00 8.00 12.00 828.00 443.00

Z30. Z31. Z32. Z33. Z34. Z35. Z36. Z37. Z38. Z39. Z40.

Per sash L.ft Sqr. Sqr. Sqr. Sqr. Sqr. Sqr. L.ft C.ft L.ft

93.00 29.00 366.00 565.00 46.00 370.00 414.00 402.00 12.00 425.00 56.00

Z41. Z42. Z43.

Corrugated asbestos sheet (corrugated sheet available) fixed with hook, bolts and nuts to roofing. Removing existing ceiling stacking materials and clearing debris. Ceiling board 6"x5/8" to 3/4" lunumidella renewing in small quantities rate to include for scaffolding (up to 30 L.ft) Ceiling lunumidella, available at site fixing with new wire nails. Removing and stacking gutter, eaves from roof of single strayed buildings. Removing and stacking gutter eaves from roof of two storied building. Removing and stacking down pipes from roof single storied building. Removing and stacking down pipe from roof of two storied building. Removing and stacking G.I. Valley gutter and flashing. Refixing existing G.I. Valley gutter and flashing including making good. Existing gutter and down pipe making and fixing complete including brackets. Chipping cement rendering and clearing debris away from floors. Demolishing floor tiles and clearing debris. Demolishing wall tiles and clearing debris. Chipping cement plastering and clearing debris away from brick walls. Chipping lime plastering and clearing debris away. Removing painting from walls and clearing debris away. Chipping cement plaster sofit & clearing away debris Removing enamel paint from door and window frame and clearing debris away. Painting ceiling beading 2 coats. Paint removing from painted glass panes with caustic soda solution or other paint remover. Removing basin , sink or urinals including all fittings and making walls good. Removing closet squatting type plugging sewer connection and floor made good. Flushing cistern disconnection, removing and plugging water connection and making good all damage to wall and floor etc. Supply and fixing ball value etc. Removing locks, brass bib ,push or stop lock 1/2" to 1 1/2" Repairing locks, bib or stop by fixing leather washers.

Sqr. Sqr. L.ft

1235.00 485.00 93.00

Z44. Z45. Z46. Z47. Z48. Z49. Z50. Z51. Z52. Z53. Z54. Z55. Z56. Z57. Z58. Z59. Z60. Z61. Z62. Z63. Z64.

Sqr. L.ft L.ft L.ft L.ft L.ft L.ft L.ft Sqr. Sqr. Sqr. Sqr. Sqr. Sqr. Sqr. Sqr. L.ft S.ft No No No

1282.00 9.00 14.00 9.00 12.00 21.00 105.00 21.00 757.00 990.00 990.00 554.00 180.00 250.00 700.00 245.00 12.00 21.00 605.00 880.00 320.00

Z65. Z66. Z67.

No No No

320.00 30.00 75.00

Z68. Z69. Z70. Z71 Z72

Repairing pillar Locks, fixed to basin carefully without damage to basin. Fixing basin lavatory existing brackets (Tap , waste tap and basin available) Removing existing locks Mortice re pairing and re-fixing. Removing water proof treatment or hot bitumen from floors or flat roof and clearing away debris. Fixing of wash basin, leveling and connecting tom existing water service and making good (basin, bracket and fitting available) Transporting debris cleared away from site by tractor (approx.. 10 Miles away). Transporting debris cleared away from site by 3.5 Cubes capacity heavy vehicle. Rate to inclusive of loading with JCB machine (approx.. 20 Miles away). MISCELLANEOUS The following items are exclusively for estimating purposes for which a standard work norm is not immediately available and at the same time it is impossible to arrive at a realistic break-up of labour component involved at the time of preparation of the estimate. The rate is not to be used for engaging labourers on routine work and the mere appearance of this rate on BSR is not a sanction to pay the daily labourers at this rate. Skilness of the Craftman to be verified by a trade test certificate at the time of engagement.

No No No S.qr No

150.00 480.00 415.00 1000.00 550.00

Z73 Z74

Load Load

2000.00 4000.00

AA

AA1

Engaging special skilled labour services in the trades of fitter, electrician, welder, mason, carpenter, bar bender, painter

Per 8 Hour day Per Person Per 8 Hour day Per Person Per Day Sq.ft.

885.00

AA2

Engaging labour services in un-skilled category of any type of manual work

732.00

AA3 AA4

Pumping water using 2" dia. water pump. Chain Link Fence Supplying & fixing PVC chain link fence (2"x 2") gauge 8 height of 10'0" for GI pipe fixed (GI pipe measured separately) with available 3/4"x 1/4" flat iron (flat iron measured separately) complete with tension J bolts and tension cords.

2440.00 96.00

AA5

Supplying & fixing PVC chain link fence (2"x 2") gauge 10 height of 10'0" for GI pipe fixed (GI pipe measured separately) with available 3/4"x 1/4" flat iron (flat iron measured separately) complete with tension J bolts and tension cords. Supplying and fixing 3" dia. Medium quality GI pipe 10') height with excavation 1'0"x 1'0"x 3'0" cement concrete base 1:2 1/2:5 (1") with 1/2" dia. MS rods welded to bottom of G.I. Pipe and drilling 9 Nos. holes to fixed the chain link (chain link measured separately) and fiberglass coping on top. Rate to include for painting one coat of anticorrosive and two coats of enamel paint. Supplying and fixing 3" dia. Medium quality GI pipe 8'0" height with excavation 1'0"x 1'0"x 3'0" cement concrete base 1:2 1/2:5 (1") with 1/2" dia. MS rods welded to bottom of G.I. Pipe and drilling 7 Nos. holes to fixed the chain link (chain link measured separately) and fiberglass coping on top. Rate to include for painting one coat of anticorrosive and two coats of enamel paint. Supplying and fixing 2" dia. Medium quality GI pipe 10'0" height with excavation 1'0"x 1'0"x 3'0" cement concrete base 1:2 1/2:5 (1") with 1/2" dia. MS rods welded to bottom of G.I. Pipe and drilling 7 Nos. holes to fixed the chain link (chain link measured separately) and fiberglass coping on top. Rate to include for painting one coat of anticorrosive and two coats of enamel paint. Supplying and fixing 2" dia. Medium quality GI pipe 8'0" height with excavation 1'0"x 1'0"x 2'0" cement concrete base 1:2 1/2:5 (1") with 1/2" dia. MS rods welded to bottom of G.I. Pipe and drilling 4 Nos. holes to fixed the chain link (chain link measured separately) and fiberglass coping on top. Rate to include for painting one coat of anticorrosive and two coats of enamel paint.

L.ft.

83.00

AA6

L.ft.

860.00

AA7

L.ft.

785.00

AA8

L.ft

465.00

AA9

L.ft.

485.00

AA10 Supplying and fixing 3/4"x 1/4" flat iron to existing GI pipe (GI pipe measured separately) to fix the chain link and drilling 09 Nos. holes. Rate to include for one coat of anticorrosive paint and two coats of enamel paint . AA11 Supplying and fixing 1 1/4"x 1 1/4"x 1/4" angle iron horizontal bracings welded to existing GI pipes including one coat of anticorrosive and two coats of Enamel paint

L.ft.

140.00

L.ft.

210.00

Sponsor Documents

Or use your account on DocShare.tips

Hide

Forgot your password?

Or register your new account on DocShare.tips

Hide

Lost your password? Please enter your email address. You will receive a link to create a new password.

Back to log-in

Close