BSR-2010

ITEM

DESCRIPTION

UNIT

RATE

B - EXCAVATION & EARTH WORK
B 01 Site preparation, Clearing site vegetation, removing bushes, shrubs & top soil to a depth not exceeding 6" and removing all debris away from site. Manual Excavation over site to reduce level in any material (except rock requiring blasting) including depositing and levelling as directed up to a distance not exceeding 30'. Manual Excavation over site to reduce level in any material (except rock requiring blasting ) including depositing and levelling as directed distance exceeding 30'-0" but not exceeding 1/4 mile. Shoring, dewatering and rock blasting if necessary for the excavation, shall be paid for separately for item B04 - B06 B 04 Manual Excavation for column, wall, staircase foundations in any material (except rock requiring blasting) up to 5'-0" depth, part return fill in and ram and surplus depositted within site as directed. Manual Excavation for column, wall, staircase foundations in any material (except rock requiring blasting) depth exceeding 5'-0" and not exceeding 10'-0", part return fill in and ram and surplus depositted within site as directed. Manual Excavation for column, wall, staircase foundations in any material (except rock requiring blasting) depth exceeding 10'-0" and not exceeding 15'-0", part return fill in and ram and surplus depositted within site as directed. Supplying and installation of pre-cast cylinders for soil improvement of 4'-0" dia. Hume pipes of wall thickness 2" and height of 2'-0"( Nominal Reinforced type ) and lowering hume pipes to loose soils with water table close to ground level toa depth of 12'-0" below the ground level. Rate shall include for removal of soil from inside the rings and lowering while dewatering up to the required depth of 12'-0".(Rate per 12'-0" depth per location) Earth work supports,(Open planking) in trenches total depth up to 5'-0", distance between opposing faces not exceeding 6'-6" Earth work supports,(Open planking) in trenches total depth exceeding 5'-0" and not exceeding 10'-0", distance between opposing faces not exceeding 6'-6" Earth work supports,(Open planking) in trenches total depth exceeding 10'-0" and not exceeding 15'-0", distance between opposing faces not exceeding 6'-6" Cube 1645.00 Sqr. 765.00

B 02

Cube

1130.00

B 03

Cube

1280.00

B 05

Cube

2525.00

B 06

Cube

2720.00

B 07

Item

16000.00

B 08

Sq.ft.

77.00

B 09

Sq.ft.

145.00

B 10

Sq.ft.

210.00

Engineering organization, W.P.

Page 1

BSR 2010

ITEM B 11

DESCRIPTION Earth work supports,(Close planking) in trenches total depth up to 5'-0", distance between opposing faces not exceeding 6'-6" Earth work supports,(Close planking) in trenches total depth exceeding 5'-0" and not exceeding 10'-0", distance between opposing faces not exceeding 6'-6" Earth work supports,(Close planking) in trenches total depth exceeding 10'-0" and not exceeding 15'-0", distance between opposing faces not exceeding 6'-6" Approved earth shall mean filling materials that comply to the following : The earth shall be free of vegetation, roots, boulders, easily decomposable materials, chemicals, industrial waste, plastic etc. The maximum size of particle shall not exceed 75mm. The earth shall be well graded and the silt and clay (fines) content shall not be more than 25% The Standerd proctor density shall be grater than 1.70g/cm3 Approved hard Earth spreading , leveling watering and manual compaction, using standered cast iron stamper or equivalent and filling in 150 mm thick layers (loose volume) in respected area (Earth available at site) Approved earth supplying within 16 Km from the source and piled at site (measured at piled volume) Transport of Earth per Km per cube for over and above 16km Off-shore Sand supply within 16km from the source (for distances over 16km, add Rs. 75 per Cube per Killo Meter) subject to the specific approval by the Divisional Engineer. Rate is applicable for loose volume. *** In case of measurements to be done on compacted volume multiply the rate by 1.2. Compaction of Earth including watering in 225mm thick layers (measured on piled volume) using machine Rammer. Rate include hire charges of the machine rammer. *** This rate is applicable for building construction with earth work not exceeding 50 cubes. (earth available at site). Manually spreading and leveling piled approved earth - H.S.R. item Ew -002 (applicable for filling out side the building area) rate without compaction. Bulk excavation using machinery

UNIT Sq.ft.

RATE 130.00

B 12

Sq.ft.

250.00

B 13

Sq.ft.

365.00

(a)

(b) (c)

(d) B 14

Cube

1130.00

B 15

Cube

1850.00

B 16 B 17

1 km Cube

120.00 6465.00

B 18

Cube

825.00

B 19

Cube

285.00

B 20

Cube

1050.00

Engineering organization, W.P.

Page 2

BSR 2010

ITEM B 21

DESCRIPTION Bulk excavation using machinery including operator, Fuel, etc...

UNIT Per Hour

RATE 500.00

C - CONCRETE
Note: The Quality of the concrete should confirm to the relevant B.S., S.L.S. and ICTAD specification for Building works. IN - SITU PLAIN CONCRETE C 01 C 02 C 03 C 04 C 05 C 06 Cement concrete 1:3:6 (2") in wall foundation(Mass concrete) Cement concrete 1:3:6 (1 1/2") in foundation and under column footings (concrete mixer) Cement concrete 1:3:6 (1 1/2") in foundation and under column footings (lean concrete of 3" thickness) Cement concrete 1:3:6 (1") in foundation and under column footings (lean concrete of 2" thickness) Cement concrete 1:3:6 (1") in foundation and under column footings Cement concrete bedding 1:2 1/2:5(1") in Floors / Toilets/ Garage/ Factory floors IN - SITU REINFORCED CONCRETE C 07 C 08 C 09 C 10 C 11 C 12 C 13 C 14 C 15 Cement concrete 1:2:4 (3/4") footings, beams/lintels and columns in ground floor using mixer and vibrator. Cement concrete 1:2:4 (3/4") in beams/lintols and columns in first floor using mixer and vibrator. Cement concrete 1:2:4 (3/4") in beams/lintols and columns in second floor using mixer and vibrator. Cement concrete 1:1 1/2:3 (3/4") using mixer and vibrator in ground floor. Cement concrete 1:1 1/2:3 (3/4") using mixer and vibrator in first floor Cement concrete 1:1 1/2:3 (3/4") using mixer and vibrator in second floor 4" Thick R.C.C slab in cement concrete 1:2:4(3/4") in first floor using mixer and vibrator. 4 1/2" thick R.C.C. slab in cement concrete 1:2:4(3/4") in floor using mixer and vibrator. first Cube Cube Cube Cube Cube Cube Sqr. Sqr. Sqr. 31750.00 32700.00 33340.00 34200.00 35230.00 35915.00 11180.00 12160.00 13145.00 Cube Cube Sqr. Sqr. Cube Cube 23910.00 25420.00 6355.00 4110.00 24655.00 26610.00

5" thick R.C.C. slab in cement concrete 1:2:4(3/4") in first floor using mixer and vibrator.

Engineering organization, W.P.

Page 3

BSR 2010

ITEM C 16 C 17 C 18

DESCRIPTION 5 1/2" thick R.C.C. slab in cement concrete 1:2:4(3/4") in first floor using mixer and vibrator. 6" thick R.C.C. slab in cement concrete 1:2:4(3/4") in first floor using mixer and vibrator. Pre-cast lintols size 9" x 6" deep in 1:2:4(3/4") cement concrete, reinforced with 3 nos of 10mm dia. tor steel bars and 6mm mild steel stirrups @ 8" c/c including necessary formwork in ground floor. Pre-cast lintols size 9" x 6" deep in 1:2:4(3/4") cement concrete, reinforced with 3 nos of 10mm dia. tor steel bars and 6mm mild steel stirrups @ 8" c/c including necessary formwork in first floor. Pre-cast lintols size 9" x 6" deep in 1:2:4(3/4") cement concrete, reinforced with 3 nos of 10mm dia. tor steel bars and 6mm mild steel stirrups @ 8" c/c including necessary formwork in second floor. Pre-cast lintols size 4 1/2" x 6" deep in 1:2:4(3/4") cement concrete, reinforced with 2 nos of 10mm dia. tor steel bars and 6mm mild steel stirrups @ 6" c/c including necessary formwork ground floor. Pre-cast lintols size 4 1/2" x 6" deep in 1:2:4(3/4") cement concrete, reinforced with 2 nos of 10mm dia. tor steel bars and 6mm mild steel stirrups @ 6" c/c including necessary formwork first floor. Pre-cast lintols size 4 1/2" x 6" deep in 1:2:4(3/4") cement concrete, reinforced with 2 nos of 10mm dia. tor steel bars and 6mm mild steel stirrups @ 6" c/c including necessary formwork in second floor. Stiffiner columns size 4" x 6" in 1:2:4 (3/4") reinforced cement concrete with 2 nos of 10mm dia. Tor steel bars , including necessary form work. Stiffiner columns size 4 1/2" x 6" in 1:2:4 (3/4") reinforced cement concrete with 2 nos of 10mm dia. Tor steel bars , including necessary form work. Stiffiner columns size 9" x 6" in 1:2:4 (3/4") reinforced cement concrete with 2 nos of 10mm dia.Tor steel bars and 6mm mild steel stirrups @ 6" c/c , including necessary form work. Copings on the 4 1/2" thick walls, size of 6 1/2" x 3" in 1:2:4 (3/4") reinforced cement concrete with 1 no of 10mm dia. Tor steel bar, including necessary form work & 1:3 cement plastering , as per the Drawing No:- AR/DETAIL DRG/2010/01/10 & Sheet No. 02

UNIT Sqr. Sqr. L.ft.

RATE 14570.00 15615.00 310.00

C 19

L.ft.

322.00

C 20

L.ft.

328.00

C 21

L.ft.

245.00

C 22

L.ft.

252.00

C 23

L.ft.

258.00

C 24

L.ft.

270.00

C 25

L.ft.

290.00

C 26

L.ft.

465.00

C 27

L.ft.

230.00

Engineering organization, W.P.

Page 4

BSR 2010

ITEM C 28

DESCRIPTION Copings on the 6" thick walls, size of 8" x 3" in 1:2:4 (3/4") reinforced cement concrete with 2 nos of 10mm dia. Tor steel bars and 6mm mild steel @ 6" c/c, including necessary form work & 1:3 cement plastering , as per the Drawing No:- AR/DETAIL DRG/2010/01/10 & Sheet No. 02 Copings on the 9" thick walls, size of 11" x 6" approx. in 1:2:4 (3/4") reinforced cement concrete with 2 nos of 10mm dia. Tor steel bars and 6mm mild steel @ 6" c/c, including necessary form work & 1:3 cement plastering , as per the Drawing No:AR/DETAIL DRG/2010/01/10 & Sheet No. 02 Cement concrete drains of internal size 9" wide and depth varies from 6" - 9" ,consist of 3" thick base and side walls in 1:3:6(1") including 1/2" thick 1:3 rendering without ramp including necessary formwork. Cement concrete drains of internal size 9" wide and depth varies from 6" - 9" ,consist of 3" thick base and side walls in 1:3:6(1") including 1/2" thick 1:3 rendering with 3" thick & 1'-6" width concrete ramp, including necessary formwork. Cement concrete drains of internal size 9" wide and depth varies from 6" - 9" ,consist of 3" thick base and side walls in 1:3:6(1") including 1/2" thick 1:3 rendering with 3" thick & 2'-6" width concrete ramp, including necessary formwork. Construction of concrete drain 300mm width x 350mm depth and varies up to 400mm. Consists of necessary excavation in hard earth, 75mm thick concrete base and walls in Grade 20 concrete, fair finish internal surface with size 450mm wide x 600mm long, 75mm thick Grade 20 removable cover slabs with side formwork. Drain and cover slab reinforced with tor steel 10mm at 150m c/c both ways. Construction of concrete drain 300mm width x 350mm depth and varies up to 400mm. Consists of necessary excavation in hard earth, 75mm thick concrete base and walls in Grade 20 concrete, fair finish internal surface without cover slab. Drain reinforced with tor steel 10mm at 150m c/c both ways. Construction of concrete drain 450mm width x 600mm minimum depth and varies up to 750mm. Consists of necessary excavation in hard earth, 100mm thick concrete base and walls in Grade 20 concrete, fair finish internal surface with adequate slope, 75mm thick Grade 20 removable cover slabs with side formwork. Drain and cover slab reinforced with tor steel 10mm at 150m c/c both ways. Construction of concrete drain 450mm width x 600mm minimum depth and varies up to 750mm. Consists of necessary excavation in hard earth, 100mm thick concrete base and walls in Grade 20 concrete, fair finish internal surface with adequate slope without cover slab, with necessary formwork. Drain reinforced with tor steel 10mm at 150m c/c both ways.

UNIT L.ft.

RATE 280.00

C 29

L.ft.

365.00

C 30

L.ft.

465.00

C 31

L.ft.

630.00

C 32

L.ft.

785.00

C 33

L.ft.

1530.00

C 34

L.ft.

1160.00

C 35

L.ft.

2705.00

C 36

L.ft.

2130.00

Engineering organization, W.P.

Page 5

BSR 2010

ITEM C 37

DESCRIPTION Casting of 6" x 6" x 6" concrete cubes on a steel mould, curing for 7 days and testing for compressive strength at an approved laboratory (rate includes transport of cubes from site to laboratory ). Continuous curing of reinforced concrete columns of size up to 18" x 18" by covering with gunnies and spraying water and keeping wet for a period of 5 days after removal of shuttering.

UNIT No.

RATE 1100.00

C 38

L.ft.

100.00

READY MIX CONCRETE C 39 C 40 C 41 C 42 C 43 C 44 C 45 Ready mix concrete of grade 20(20 N/mm2) confirming to SLS 1144-1997, transport 20km from batching plant. Ready mix concrete of grade 25(25 N/mm2) confirming to SLS 1144-1997, transport 20km from batching plant. Ready mix concrete of grade 30(30 N/mm2) confirming to SLS 1144-1997, transport 20km from batching plant. Transport charges per Km per m3 for over and above 20 km. Placing , levelling , vibrating the concrete. Pumping charge for quantites up to 35 m3 by pump car For more than 35 m additional pumping charges. (Rate for every m3 over and above 35 m3)
3

Cu.m Cu.m Cu.m

9615.00 9940.00 10425.00

Km Cu.m Item Cu.m

34.00 400.00 12000.00 400.00

D - FORM WORK
Note: The rates given for items D 02, D 03 to D 08 herein are applicable for plywood sheets of 15 mm thick. Hence the rate is valid only if the shuttering / formwork for footing , column , beams , lintel, walls, slabs are of 15 mm thick ply boards. Any deviation from the specified materials, specified thickness and the arrangement of formwork given in this document should require the written approval of the Divisional Engineer. Rate for such deviation from the item description will be decided by the D(B/SW) For ordinary plywood of 15 mm thick boarding as shuttering, (Even for WBP sheets the same rate shall be applicable). Shuttering for sides of foundation with 1" thick rubber planking including dismantling Shuttering for sides and bottom of plinth beams, ground beams including dismantling in 15mm thick plywood board. Sqr. Sqr. 3725.00 13385.00

(a)

(b)

(c) D 01 D 02

Engineering organization, W.P.

Page 6

BSR 2010

ITEM D 03 D 04 D 05 D 06 D 07 D 08

DESCRIPTION Shuttering for floor slab including dismantling in 15mm thick Plywood board. Shuttering for columns including dismantling in 15mm thick Plywood board. Shuttering for Beams/Lintols including dismantling in 15mm thick Plywood Board Shuttering for floor slab including dismantling in 15mm thick Plywood board support by scaffolding up to 12'. Shuttering for floor slab including dismantling in 15mm thick Plywood board support by scaffolding up to 16'. Shuttering for Beams/Lintols including dismantling in 15mm thick Plywood Board support by G.I Jack. Note: The rates given in Items D09, D10, D11 herein are applicable for Rubber planks. The rubber planks are allowed only for minor works and should be used with the written approval of the D.E.

UNIT Sqr. Sqr. Sqr. Sqr. Sqr. Sqr.

RATE 12080.00 15850.00 18735.00 10570.00 11060.00 17115.00

D 09 D 10 D 11

Shuttering for Beams/Lintols including dismantling. Shuttering for stiffener columns between wall panels in 9" walls, 4 1/2" walls and in boundary walls. Shuttering for R.C.C. copings in top of balcony , stair and boundary walls and pre - cast lintel sides

Sqr. Sqr. Sqr.

5700.00 5100.00 3700.00

E - REINFORCEMENT
E 01 Mild steel reinforcement to slabs, beams, lintols, columns, footings & etc.. bent to shape, laid in position and tied with 16 B.W.G. binding wire in Ground floor . Mild steel reinforcement to slabs, beams, lintols, columns, footings & etc.. bent to shape, laid in position and tied with 16 B.W.G. binding wire in first floor . Mild steel reinforcement to slabs, beams, lintols, columns, footings & etc.. bent to shape, laid in position and tied with 16 B.W.G. binding wire in second floor . Tor steel reinforcement to slabs, beams, lintols, columns, footings & etc.. bent to shape, laid in position and tied with 16 B.W.G. binding wire in Ground floor. Tor steel reinforcement to slabs, beams, lintols, columns, footings & etc.. bent to shape, laid in position and tied with 16 B.W.G. binding wire in first floor. Kg 150.00

E 02

Kg

154.00

E 03

Kg

157.00

E 04

Kg

150.00

E 05

Kg

154.00

Engineering organization, W.P.

Page 7

BSR 2010

ITEM E 06

DESCRIPTION Tor steel reinforcement to slabs, beams, lintols, columns, footings & etc.. bent to shape, laid in position and tied with 16 B.W.G. binding wirein second floor. Rate for testing of Tor-steel specimen of 1m length for mechanical properties at an approved laboratory. Application of two coats of Corrosion resistant primer of "BARRA ZINC SP" or equivalent to all exposed reinforcements including preparing surfaces.

UNIT Kg

RATE 157.00

E 07 E 08

Sample Sq.ft.

3800.00 115.00

F - BRICK MASONRY
F 01 F 02 F 03 F 04 F 05 F 06 F 07 F 08 F 09 F 10 F 11 Brick work in cement and sand 1:8 in foundation up to D.P.C. level. Brick work in cement and sand 1:8 in super Structure in ground floor. ( 9" thick brick work) Brick work in cement and sand 1:8 in 1st floor level.(9" thick brick work) Brick work in cement and sand 1:8 in 2nd floor level.(9" thick brick work) Brick work in cement and sand 1:8 in superstructure in ground floor (8" thick brick work) Brick work in cement and sand 1:8 in 1st floor level.(8" thick brick work) Brick work in cement and sand 1:8 in 2nd floor level.(8" thick brick work) Brick work in cement and sand 1:5 in 4 1/2" thick walls in ground floor. Brick work in cement and sand 1:5 in 4 1/2" thick walls in 1st floor Brick work in cement and sand 1:5 in 4 1/2" thick walls in 2nd floor Brick drain internal size 9" x 9"(average depth) , including excavation, back filling , 3" thick plain concrete 1:3:6(1") base, 4 1/2" thick Brick side walls in cement and sand mortar 1:5 , rendering 1/2" thick cement and sand 1:3 and finish smooth with cement putty. 3" thick brick paving in cement and sand 1:8 mix 4 1/2" thick wire cut brick wall in cement and sand 1:5 in ground floor. 4 1/2" thick wire cut brick wall in cement and sand 1:5 in first floor. Cube Cube Cube Cube Cube Cube Cube Sqr. Sqr. Sqr. L.ft. 23900.00 24695.00 25930.00 26425.00 20195.00 21200.00 21600.00 10200.00 10710.00 10915.00 360.00

F 12 F 13 F 14

Sqr. Sqr. Sqr.

7185.00 12930.00 13580.00

Engineering organization, W.P.

Page 8

BSR 2010

ITEM F 15 F 16 F 17 F 18 F 19

DESCRIPTION 4 1/2" thick wire cut brick wall in cement and sand 1:5 in second floor. 9" thick wire cut brick wall in cement and sand 1:5 in ground floor. 9" thick wire cut brick wall in cement and sand 1:5 in first floor. 9" thick wire cut brick wall in cement and sand 1:5 in second floor. Steps 1' - 1 1/2" in brick in cement and sand 1:5 with 1/2" thick rendering in cement and sand 1:2 including 6" high foundation.

UNIT Sqr. Sqr. Sqr. Sqr. L.ft.

RATE 13840.00 24590.00 25820.00 26315.00 260.00

F 20 F 21 F 22

Brick piers in cement and sand 1:5 in ground floor. Brick piers in cement and sand 1:5 in first floor. Brick piers in cement and sand 1:5 in second floor.

Cube Cube Cube

25960.00 27260.00 27780.00

G - CELLULAR AND SOLID BLOCK MASONRY
G 01 8" thick cement sand Cellular block wall (blocks confirming to S.L.S. 855 and subject to the approval of the quality of the blocks) in cement and sand mortar 1:5 in ground floor. 6" thick cement sand Cellular block wall (blocks confirming to S.L.S. 855 and subject to the approval of the quality of the blocks) in cement and sand mortar 1:5 in ground floor. 4" thick cement sand Cellular block wall (blocks confirming to S.L.S.855 and subject to the approval of the quality of the blocks) in cement and sand mortar 1:5 in ground floor. 6" thick cement sand Solid block wall (blocks confirming to S.L.S. and subject to the approval of the quality of the blocks) in cement and sand mortar 1:5 in ground floor. 4" thick cement sand Solid block wall (blocks confirming to S.L.S and subject to the approval of the quality of the blocks) in cement and sand mortar 1:5 in ground floor. Supply and fixing 1'-0" x 1'-0" cement grill on wall. Supply and fixing glass blocks size 8" x 8" Sqr. 14995.00

G 02

Sqr.

11380.00

G 03

Sqr.

8670.00

G 04

Sqr.

14525.00

G 05

Sqr.

11655.00

G 06 G 07

Sq.ft. Sq.ft.

125.00 900.00

H - RUBBLE MASONRY
H 01 Random rubble (6"-9") masonry in cement mortar 1:5 in wall foundation and retaining walls. Cube 18220.00

J - FLOORING
J 01 3/4" thick D.P.C. in cement sand 1:2 finished with 2 coats of D.P.C. tar and blinded with sand. Sqr. 6500.00

Engineering organization, W.P.

Page 9

BSR 2010

ITEM J 02 J 03

DESCRIPTION Gauge 700 polythene damp proof membrane with 6" laps laid under floors Rendering 1/2" thick in cement and sand 1:2 in exposed concrete surfaces and garage floors finished smooth with neat cement slurry. Rendering 1/2" thick in cement and sand 1:2 in exposed concrete surfaces and garage floors finished smooth with colour pigment. ( Pigment added at 2.5 Kg / Sqr ) Rendering 1/2" thick in cement and sand 1:3 in R.C.C. floors and paved floors finished smooth with neat cement slurry and colour pigment. Rendering 1/2" thick in cement and sand 1:3 in R.C.C. floors and paved floors finished smooth without colour pigment. 1/2" thick Rendering to the top surface of the sunshade with cement and sand 1:3 finished smooth and treated with two coats of "Aqua Tuff " by M/s Lankem or approved equivalent and 1:8 slope should be made. Skirting 4" x 1/2" thick in cement and sand 1:3 projected or flush to walls finished with cement floating including forming groove.

UNIT Sqr. Sqr.

RATE 300.00 3685.00

J 04

Sqr.

4325.00

J 05

Sqr.

3800.00

J 06 J 07

Sqr. Sqr.

3225.00 5800.00

J 08

L.ft.

53.00

J 09

Skirting 4" x 1/2" thick in cement and sand 1:3 projected or flush to walls finished with colour pigmented neat cement including forming groove. Skirting 6" x 1/2" thick in cement and sand 1:3 projected flush to walls finished with cement floating including forming groove in neat cement slurry. Skirting 6" x 1/2" thick in cement and sand 1:3 projected flush to walls finished with colour pigmented neat cement including forming groove. 3" thick brick paving in cement sand 1:8 and 1/2" thick cement rendered in 1:3 floated with neat cement. 3" thick brick paving in cement sand 1:8 and 1/2" thick cement rendered in 1:3 floated with neat cement and colour pigment. Floor cement concrete in 1:2 1/2":5(1") to a thickness of 3" with 1/2" thick rendering 1:2 with expansion joints filled with cement and sand. Brick work in cement 1:5 wearing & throating on 4 1/2" brick wall including 1/2" thick 1:3 cement rendering Brick work in cement 1:5 wearing & throating on 9" brick wall including 1/2" thick 1:3 cement rendering

L.ft.

57.00

J 10

L.ft.

66.00

J 11

L.ft.

72.00

J 12 J 13 J 14

Sqr. Sqr. Sqr.

12080.00 12725.00 10250.00

J 15 J 16

L.ft. L.ft.

186.00 255.00

Engineering organization, W.P.

Page 10

BSR 2010

ITEM

DESCRIPTION

UNIT

RATE

Water Proofing
The rates for Items J 17 to J 20 are strictly applicable, subject to the fulfillment of the following conditions. The waterproofing contractor (or sub-contractor) should be a registered specialist contractor at the ICTAD in the category of water proofing. The Contractor shall submit a written warranty of at least 5 year to cover on the quality of the material, suitability of the material for the situation and the workmanship including water tightness. The water proofing material shall conform to relevant British, Euro or ASTM specifications Application of liquid polymer cement water proofing agents for the following areas: Water Proofing the inner surface of walls and floor slab of toilets and balconies where a waterproofing is necessary before tiling, Application of "Baralastic" polymer modified cementitious waterproofing agent after cleaning the subtrate all as per manufacturer's specifications with 10 years warranty on application.Rate shall include for ponding test for a 300mm water height kept for a period of 48 hours. Flat roofs, concrete/masonry tanks, wet areas of toilets including bathrooms, exposed balconies, concrete gutters. "Smart flex", "Tharoseal" or any other equivalent product marketed/installed by specialist contractor registered at ICTAD. Sq.ft. 240.00

(a)

(b)

(c) (d) J 17

J 18

Sq.ft.

195.00

Application of cementitious type agents J 19 On newly cast under ground sumps, swimming pools basements. "Osmoseal", "Xypex", "Vandex" or any other equivalent product marketed/installed by a specialist contractor registered at ICTAD. Sq.ft. 310.00

Application of membrane type agents J 20 On large flat roofs, gutters, basements. "POLYFLEX" - 3mm thick bituman based membrane or any other equivalent product marketed/installed by a specialist contractor registered at ICTAD, including 1 : 3 cement,sand protective screed laid to slope. Rate shall include the formation of edges, torch welding and metal strip on vertical walls. *** The above rates include the cost of surface preparation, but do not include the cost of protective masonry screed. The approving authority for equivalent products will be the Deputy Chief Secretary (Engineering) Sq.ft. 395.00

Engineering organization, W.P.

Page 11

BSR 2010

ITEM

DESCRIPTION

UNIT

RATE

Anti-Tretement
J 21 Anti-tretement for the new construction with applying Biflexthrine 10Tc (Biflex ) or approved equivelant , Dialuted chemicals 1:200 ratio with water after supplying the sealed bottle with lables to the site and should be followed the manufacture standards of application including horizontal & vertical barriers. It should be 10 years warranty on application. Sq.ft. 17.00

J 22

Anti-tretement for the post construction (Existing building ) with applying Biflexthrine 10Tc (Biflex ) or approved equivelant , Dialuted chemicals 1:200 ratio with water after supplying the sealed bottle with lables to the site and should be followed the manufacture standards of application including horizontal & vertical barriers. It should be not less than 5 years warranty on application.

Sq.ft.

21.00

K - PLASTERING
K 01 K 02 5/8" thick plastering to plinth wall in cement sand 1:3 including cement floating. Plastering 5/8" thick to walls in cement, lime or equivelent chemical product (Febmix) and sand 1:1:5 finished semi-rough with wooden float. (Sand to be seived). Plastering 5/8" thick to reveals width not exceeding 6" in cement, lime or equivelent chemical product (Febmix) and sand 1:1:5 finished semi-rough with wooden float. Plastering 5/8" thick to walls in cement, lime or equivelent chemical product (Febmix) and sand 1:1:5 finished smooth with lime putty. Plastering 5/8" thick to reveals width not exceeding 6" in cement, lime or equivelent chemical product (Febmix) and sand 1:1:5 finished smooth with lime putty. Plastering 3/8" thick to soffit of slab, sunshade, sides and soffit of beams, stair cases and sides of columns in cement and sand 1:3 including floating with lime putty. Plastering 3/8" thick to soffit of slab, sunshade, sides and soffit of beams, stair cases and sides of columns in cement & sand 1:3 finished semi rough with wooden float. Forming drip for sunshade edge cement & sand 1: 2 finish semi rough. Plastering 3/4" thick to black board in cement & sand 1:3 finish semi rough and Rendering cement floating coat using black cement finished smooth with carborandum stone. Including preparation of border. Sqr. Sqr. 3545.00 3650.00

K 03

L.ft.

81.00

K 04

Sqr.

4775.00

K 05

L.ft.

91.00

K 06

Sqr.

5640.00

K 07

Sqr.

5260.00

K 08 K 09

L.ft. Sqr.

75.00 10470.00

Engineering organization, W.P.

Page 12

BSR 2010

ITEM K 10

DESCRIPTION Plaster bands 6" x 1/2" in cement & sand 1:3 finished semi rough, extra over the plastering as per the Drawing No:- AR/DETAIL DRG/2010/01/10 & Sheet No. 01 Plaster bands 9" x 1/2" in cement & sand 1:3 finished semi rough, extra over the plastering as per the Drawing No:- AR/DETAIL DRG/2010/01/10 & Sheet No. 01

UNIT L.ft.

RATE 110.00

K 11

L.ft.

140.00

L - TILING
Note: Tiles should comply with European standard specification CEN 177. For Item L01 - L03 Should be tile range manufractured by Lanka Wall Tile or approved equivalant. Wall Tiling L 01 Glazed ceramic wall tiling of size 8" x 12" approved colour, supplying and fixing to walls on a 1:3 cement sand mortar layer, and pointed with tile grout to match the tile. *** (Rate does not include the 1:3 cement sand mortar layer and is separately measured under item L04) Glazed ceramic wall tiling of size 12" x 16" approved colour, supplying and fixing to walls on a 1:3 cement sand mortar layer, and pointed with tile grout to match the tile. *** (Rate does not include the 1:3 cement sand mortar layer and is separately measured under item L04) Glazed porcelain wall tiling of size 24" x 12" approved colour, supplying and fixing to walls on a 1:3 cement sand mortar layer, and pointed with tile grout to match the tile. *** (Rate does not include the 1:3 cement sand mortar layer and is separately measured under item L04) Cement and sand 1:3 screed of 1/2" thick backing to receive wall tiles. Floor Tiling Note : For Item No. L05 to L16 Shall be Homogenous, Vitreous porcelain floor tiles of industrial grade (heavy duty) Floor tile range manufractured by Rocell or approved equivalant. *** Rate includes the cost of 1:3 motar leveling bed. L 05 Homogeneous vitreous porcelain glazed or unglazed floor tile 8" x 8" paving on 1:3 cement & sand bedding and pointed with tile grout to match the tile. ( Heavy duty ) Sqr. 26280.00 Sqr. 23630.00

L 02

Sqr.

22795.00

L 03

Sqr.

35285.00

L 04

Sqr.

3160.00

Engineering organization, W.P.

Page 13

BSR 2010

ITEM L 06

DESCRIPTION Homogeneous vitreous porcelain glazed or unglazed floor tile 12" x 12" paving on 1:3 cement & sand bedding and pointed with tile grout to match the tile. ( Heavy duty ) Homogeneous vitreous porcelain glazed or unglazed floor tile 16" x 16" paving on 1:3 cement & sand bedding and pointed with tile grout to match the tile. ( Heavy duty ) Homogeneous vitreous porcelain polished floor tile 12" x 12" paving on 1:3 cement & sand bedding and pointed with tile grout to match the tile.( Heavy duty ) Homogeneous vitreous porcelain polished floor tile 16" x 16" paving on 1:3 cement & sand bedding and pointed with tile grout to match the tile. ( Heavy duty ) Homogeneous vitreous porcelain glazed floor tile 18" x 18" paving on 1:3 cement & sand bedding and pointed with tile grout to match the tile. ( Heavy duty ) Homogeneous vitreous porcelain rectified floor tile 24" x 12" paving on 1:3 cement & sand bedding and pointed with tile grout to match the tile. ( Heavy duty ) Homogeneous vitreous porcelain rectified floor tile 24" x 16" paving on 1:3 cement & sand bedding and pointed with tile grout to match the tile. ( Heavy duty ) Homogeneous vitreous porcelain rustic floor tile 12" x 12" for garage & balcony areas paving on 1:3 cement & sand bedding and pointed with tile grout to match the tile. ( Heavy duty ) Supply and laying of 4" high skirting including tile grout to match the tile of tiling confirming to items L 05 to L 13 Supply and laying of 4" high skirting including tile grout to match the tile for staircases. Supplying and laying homogeneous vitreous porcelain tiles at staircase treads including nosing type paving on 1:3 cement & sand bedding and pointed with tile grout to match the tile.

UNIT Sqr.

RATE 25980.00

L 07

Sqr.

26440.00

L 08

Sqr.

39945.00

L 09

Sqr.

40680.00

L 10

Sqr.

24445.00

L 11

Sqr.

31940.00

L 12

Sqr.

29120.00

L 13

Sqr.

25470.00

L 14 L 15 L 16

L.ft. L.ft. Sqr.

98.00 120.00 43940.00

Note :
The tiles specified in L17 to L22 are exclusively for residential/non-public area as specified by an Architect. The rate is applicable for tiles manufactured by Rocell or equilant and are of coloured designed tiles. L 17 L 18 Lay Ceramic glazed floor tiles 12" x 12" paving on 1:3 cement sand bedding and pointed with tile grout to match the tile. Lay Ceramic glazed floor tiles 13" x 13" paving on 1:3 cement sand bedding and pointed with tile grout to match the tile. Sqr. Sqr. 20850.00 24325.00

Engineering organization, W.P.

Page 14

BSR 2010

ITEM L 19 L 20 L 21 L 22

DESCRIPTION Lay Ceramic glazed floor tiles 16" x 16" paving on 1:3 cement sand bedding and pointed with tile grout to match the tile. Lay Ceramic glazed floor tiles 18" x 18" paving on 1:3 cement sand bedding and pointed with tile grout to match the tile. Lay Ceramic glazed floor tiles 24" x 12" paving on 1:3 cement sand bedding and pointed with tile grout to match the tile. Lay Ceramic glazed floor tiles 24" x 16" paving on 1:3 cement sand bedding and pointed with tile grout to match the tile. Note : Rate for tiling should include for cement and sand 1:3 backing 20mm thick including pointing and grout to match with tiles colours and sizes of tiles to approval by the Architect.

UNIT Sqr. Sqr. Sqr. Sqr.

RATE 22625.00 24820.00 31610.00 28640.00

L 23

Rough heavy duty bathroom floor tiles of size 8" x 8" of Rocell or equivalent, paving on 1:3 cement sand bedding and pointed with tile grout to match the tiles. Rough heavy duty bathroom floor tiles of size 12" x 12" of Rocell or equivalent, paving on 1:3 cement sand bedding and pointed with tile grout to match the tiles. Granite The Granite specified sizes,colour and details of paving decided by Architect and sample should be approved by the Architect before the construction. The rate is applicable for Granite manufactured by "Ally Weerasinghe" or approved equivalent. Granite should be without any defects from oils , detergents & chemicals

Sqr.

23250.00

L 24

Sqr.

22770.00

L 25

Polished Granite size 1'-0" x 1'-0" x 3/4" thick absolutely black for vanity top of "Ally Weerasinghe" or approved equivalent , laid on 1/2" thick cement sand 1:3 screed level off using cement slurry and 1mm joints to be absolutely in line and flush and grout. Polished Granite floor slabs of size 1'-0" x 1'-0" x 3/4" thick absolutely black of "Ally Weerasinghe" or approved equivalent , laid on 1/2" thick cement sand 1:3 screed level off using cement slurry and 1mm joints to be absolutely in line and flush and grout. Granite floor slabs of size 1'-0" x 1'-0" x 3/4" thick rough finish of "Ally Weerasinghe" or approved equivalent , laid on 1/2" thick cement sand 1:3 screed level off using cement slurry and 1mm joints to be absolutely in line and flush and grout.

Sqr.

175210.00

L 26

Sqr.

175210.00

L 27

Sqr.

58640.00

Engineering organization, W.P.

Page 15

BSR 2010

ITEM L 28

DESCRIPTION Granite floor slabs of size 1'-0" x 1'-0" x 3/4" thick gloss finish of "Ally Weerasinghe" or approved equivalent , laid on 1/2" thick cement sand 1:3 screed level off using cement slurry and 1mm joints to be absolutely in line and flush and grout. Granite floor slabs of size 2'-0" x 1'-0" x 3/4" thick gloss finish of "Ally Weerasinghe" or approved equivalent , laid on 1/2" thick cement sand 1:3 screed level off using cement slurry and 1mm joints to be absolutely in line and flush and grout.

UNIT Sqr.

RATE 58640.00

L 29

Sqr.

97070.00

M - COLOUR WASHING, PAINTING & POLISHING
M 01 M 02 M 03 M 04 M 05 M 06 M 07 M 08 M 09 M 10 M 11 M 12 M 13 M 14 White washing walls two coats in single storied building including preparing surface. White washing walls two coats in two storied building including preparing surface. Painting walls with one coat of wall primer. Painting walls with one coat of emulsion paint. Painting walls with two coats of emulsion paint . Painting soffit with one coat of emulsion paint. Painting soffit with two coats of emulsion paint. Painting walls with onecoat of weather shield. Painting walls with two coats of weather shield. Painting walls & soffits with one coat of crack binder primer. Cement washing two coats to walls in single storied buildings including preparing surface. Painting walls with enamel paint one coat. Painting walls with enamel paint two coats. Application of plaster coatings of thickness not less than 2mm using "Joint compound powder / Skimcoat ", or approved equivalent to walls, slab, beam, column facings.Rate shall include for sand papering and surface preparation. Painting black boards with two coats of blackboard paint. Preparing and painting old wood work with one coat of enamel paint. Preparing and painting old wood work with two coats of enamel paint. Preparing and painting new wood work with primer and two coats enamel paint. Sqr. Sqr. 475.00 490.00

Sqr. Sqr. Sqr. Sqr. Sqr. Sqr. Sqr. Sqr. Sqr. Sqr. Sqr. Sqr.

1225.00 880.00 1770.00 995.00 1995.00 1340.00 2160.00 2195.00 385.00

1075.00 2310.00 3480.00

M 15 M 16 M 17 M 18

Sqr. Sqr. Sqr. Sqr.

2195.00 1340.00 2110.00 2770.00

Engineering organization, W.P.

Page 16

BSR 2010

ITEM M 19

DESCRIPTION Preparing and application of water based stain and two coats of water based sealant to new wood work. Rate shall include for preparing the surface. Varnishing two coats with polyurethane varnish after sand papering and application of sealer coat Spray Painting for the wood work as per specified in SCA/4/1 clause 14.9 ( f ). Wax polishing to timber in panels and floors. Applying one coat of approved type floor polish including smoothing. Painting floors with one coat of quick drying floor paint including washing and cleaning surfaces. Painting steel work with one coat of anti-corrosive paint with primer including removing corroded scale and wire brushing. Painting steel work with two coats of anti-corrosive paint with primer including removing corroded scale and wire brushing. Painting steel work with one coat of "EPLACK EPOXY COALTAR" or approved equivalent as per manufacturer's specifications. Labour rate for two coats of Emulsion Painting walls including scaffolding (Paint & Brushes supplied by the client) Labour rate for single coat of Emulsion Painting walls including scaffolding (Paint & Brushes supplied by the client) Labour rate for two coats of enamel painting (Paint & Brushes supplied by the client)

UNIT Sqr.

RATE 11570.00

M 20 M 21 M 22 M 23 M 24 M 25 M 26 M 27

Sqr. Sqr.

2560.00 3200.00

Sqr. Sqr. Sqr.

680.00 1080.00 1395.00

Sqr. Sqr.

1135.00 1610.00

Sqr.

2525.00 680.00

M 28 M 29 M 30

Sqr. Sqr. Sqr. 455.00 975.00

N - DOORS & WINDOWS
Timber : Refer preamble note for approved species. Finished door sash size of less than 1" thicknesses not allowed. Glass thickness to be 5mm. Rate shall include for following heavy duty brass furniture. Doors :- 3 no. 4"x 3" Solid brass hinges Doors :- 2 no. 6" Solid brass barral bolts Windows of 4'-0" ht. abo :- 2 no. 4"x 2" Solid brass hinges

1

2 (a) (b) (c)

(d)

Windows above 4'-0" ht. o:- 3 no. 4"x 2" Solid brass hinges

Engineering organization, W.P.

Page 17

BSR 2010

ITEM (e) (f) (g)

DESCRIPTION Windows :- 1 no. 2" Solid brass Brass ring Windows :- 1 no. 10" Solid brass Casement Stay Windows :- 1 no. Solid brass Casement Fastner Doors

UNIT

RATE

N 01

Door flush paneled 1 1/8" thick single sash hung on 3 3/4" x 3/4" frame. Rate without brass furniture, painting and lock.

2

Sq.ft.

770.00

N 02

Door glazed and paneled 1 1/8" thick single sash hung on 3 3/4" x 2 3/4" frame. Rate without brass furniture, painting and lock. Door flush paneled 1" thick single sash hung on 3 3/4" x 2 3/4" frame. Rate without brass furniture, painting and lock. Door glazed and paneled 1" thick single sash hung with 3 3/4" x 2 3/4" frame . Rate without brass furniture, painting and lock. Door 30mm thick plywood ordinary sash single hung on 3 3/4" x 2 3/4" frame. Rate without brass furniture, painting and lock. Door 30mm thick plywood (marine) sash single hung on 3 3/4" x 2 3/4" frame. Rate without brass furniture, painting and lock. Door or window glazed and/or paneled 1 1/8" thick double sash hung on 3 3/4" x 2 3/4" frame. Rate without brass furniture, painting and lock. Door/Window ledged, braced & battened with 3 3/4" x 2 3/4" frames and 7/8" thick sash made out of GINISAPU. Rate without brass furniture, painting and lock. Supply & fixing 1 1/8" thick flush paneled door sash only. Rate without brass furnitures, door lock and painting. Supply & fixing 1" thick flush paneled door sash only. Rate without brass furnitures, door lock and painting. Supply & fixing 1 1/8" thick glazed & paneled door sash only. Rate without brass furnitures, door lock and painting. Supply & fixing 1" thick glazed & paneled door sash only. Rate without brass furnitures, door lock and painting. Supply & fixing 30mm thick plywood door sash only. Rate without brass furnitures, door lock and painting. Door frame 3 3/4" x 2 3/4" in approved timber supplying & fixing in position.

Sq.ft.

760.00

N 03 N 04

Sq.ft. Sq.ft.

725.00 740.00

N 05

Sq.ft.

465.00

N 06

Sq.ft.

445.00

N 07

Sq.ft.

795.00

N 08

Sq.ft.

715.00

N 09 N 10 N 11 N 12 N 13 N 14

Sq.ft. Sq.ft. Sq.ft. Sq.ft. Sq.ft. Sq.ft.

590.00 575.00 600.00 575.00 270.00 410.00

Engineering organization, W.P.

Page 18

BSR 2010

ITEM Windows N 15 N 16 N 17 N 18 N 19 N 20 N 21 N 22

DESCRIPTION

UNIT

RATE

Window glazed 1 1/8" sash and 3 3/4" x 2 3/4" frame. Rate without brass furniture, painting. Window glazed 1" sash and 3 3/4" x 2 3/4" frame. Rate without brass furniture, painting. Window glazed 7/8" sash and 3 3/4" x 2 3/4" frame. Rate without brass furniture, painting. Timber slats with 3 3/4" x 1 3/4" frame , 1" x 2 1/2" vertical slats at 2 1/2" centers. Painting measured separately. Supply & fixing 1 1/8" thick glazed window sash only. Rate without brass furnitures and painting. Supply & fixing 1" thick glazed window sash only. Rate without brass furnitures and painting. Supply & fixing 7/8" thick glazed window sash only. Rate without brass furnitures and painting. Window frame 3 3/4" x 2 3/4" in approved timber supplying & fixing in position.

Sq.ft. Sq.ft. Sq.ft. Sq.ft. Sq.ft. Sq.ft. Sq.ft. Sq.ft.

765.00 745.00 715.00 480.00 575.00 550.00 545.00 420.00

P - BRASS FOUNDER
Note: All Iron mongary shall be heavy duty and samples should be approved by the D.E. Prior to installation. In view of the variety of door locks available in the market, it has become necessary to prescribe the exact quality requirements in terms of performance and durability aspects. The "Union" brand and respective model numbers have been choosen as a bench mark to establish the said requirements. The brand name and model number appearing in the respective BSR items are purely meant to describe the performance standard of the said fitting/item and does not imply in any manner that only the "Union" brand is recommended or considered to be restricted to the "Union" brand. Any other make/brand that has equivalent performance characteristics are considered as equivalent provided such fittings met with following criteria. has an authorized local agent in Sri Lanka The local agent has been in the trade of the offered make for not less than 5 years. The fittings are manufactured in conformity to BS, JIS, A.S.T.M., A.S. or S.L.S. standards.

1

2

3

(a) (b)

(c)

Engineering organization, W.P.

Page 19

BSR 2010

ITEM (d)

DESCRIPTION The dimensions are/and performance characteristics are in par with the stated model. The brands that may be considered as equivalent are "Miva" of Japan "Whitco" of Australian make or "Dorma" of European make.or any other approved make which prior approval to be obtained from Deputy Chief Secretary (Engineering) after producing necessary catalogues documents. The BSR Items No. P 16 - P 21 , P 23 & P 25 - P 27 are payable only after producing an original invoice from the authorized agent for "Union" brand. Supplying and fixing 4" x 2 1/2" x 2.5mm thick solid brass hinges with-out ball bearing inclusive of brass screws marketted by M.M.Noorbhoy & company or approved equivalent. Supplying and fixing 4" x 3" x 2.5mm thick solid brass hinges with-out ball bearing inclusive of brass screws marketted by M.M.Noorbhoy & company or approved equivalent. Supplying and fixing 5" x 3" x 2.5mm thick solid brass hinges with-out ball bearing inclusive of brass screws marketted by M.M.Noorbhoy & company or approved equivalent. Supplying and fixing heavy duty soild brass casement fastener inclusive of brass screws marketted by M.M.Noorbhoy & company or approved equivalent. Supplying and fixing heavy duty solid brass casement stay - 6" inclusive of brass screws marketted by M.M.Noorbhoy & company or approved equivalent. Supplying and fixing heavy duty solid brass casement stay - 12" inclusive of brass screws marketted by M.M.Noorbhoy & company or approved equivalent. Supplying and fixing heavy duty solid brass 4" centre pivot inclusive of brass screws marketted by M.M.Noorbhoy & company or approved equivalent. Supplying and fixing 4" long heavy duty solid brass tower bolt inclusive of brass screws marketted by M.M.Noorbhoy & company or approved equivalent. Supplying and fixing 6" long heavy duty solid brass tower bolt inclusive of brass screws marketted by M.M.Noorbhoy & company or approved equivalent. Supplying and fixing 8" long heavy duty solid brass tower bolt inclusive of brass screws marketted by M.M.Noorbhoy & company or approved equivalent. Supplying and fixing 10" long heavy duty solid brass tower bolt inclusive of brass screws marketted by M.M.Noorbhoy & company or approved equivalent.

UNIT

RATE

4

5

P 01

No.

945.00

P 02

No.

1110.00

P 03

No.

1340.00

P 04

No.

875.00

P 05

No.

605.00

P 06

No.

1115.00

P 07

Pair

560.00

P 08

No.

800.00

P 09

No.

1030.00

P 10

No.

1530.00

P 11

No.

1885.00

Engineering organization, W.P.

Page 20

BSR 2010

ITEM P 12 P 13 P 14 P 15

DESCRIPTION Supplying and fixing solid brass Door or Window pull ring of 1" dia. ( Small ) Supplying and fixing solid brass Door or Window pull ring of 1 1/4" dia. ( Medium ) Supplying and fixing solid brass Door or Window pull ring of 2" dia. ( Large ) Supplying and fixing solid brass fanlight catch. Supply and fixing Stainless Steel hinges of size 102 x 76 x 2mm of Union Brand & Model no.- X8203-BB-2 or approved equivalent. Supply and fixing Stainless Steel hinges of size 102 x 76 x 3mm of Union Brand & Model no.- X8203-BB-3 or approved equivalent. Supply and fixing Stainless Steel hinges of size 127 x 89 x 3mm of Union Brand & Model no.- X8205-BB-3 or approved equivalent. Supplying and fixing Night - latch lock of Union Brand & Model No. -1028 WEPL or approved equivalent. Supplying and fixing Night - latch lock of Union Brand & Model No. -1022 SEPL or approved equivalent. Supplying and fixing two lever Mortice door lock for single sash of Union Brand & Model no.-678.24.95 CH or approved equivalent. Supplying and fixing two lever Mortice door lock for double sash of Raniyo Brand & Model no.- 965.41.94 CH or approved equivalent. Supplying and fixing cylindrical door lock of Union Brand & Model no. -96300-SS.or approved equivalent

UNIT No. No. No. No.

RATE 265.00 300.00 340.00 935.00

P 16

Pair

2540.00

P 17

Pair

3070.00

P 18

Pair No. No. No.

2865.00 7960.00 9425.00 4890.00

P 19 P 20

P 21

No.

5860.00

P 22

No. No. No. No.

5030.00 1820.00 6135.00 1225.00

P 23 P 24 P 25

Supplying & fixing rim lock of Raniyo Brand & Model no. 1445 or approved equivalent. Supplying & fixing hydraulic door closer of Union Brand & Model no. - 8823 SIL or approved equivalent. Supplying & fixing stainless steel Male or Female Symbol of Union Brand & Model no. - 200SS or approved equivalent. Supplying & fixing stainless steel Disabled Symbol of Union Brand or approved equivalent.
Supplying and fixing mortice lock - Imported chinese Supplying and fixing Yale mortice lock - (Italy make) Supplying and fixing cupboard door lock - 808 Supplying and fixing magnet lock

P 26

No.

1500.00

P 27 P 28 P 29 P 30 P 31

No. No. No. No.

2025.00 2695.00 600.00 70.00

Engineering organization, W.P.

Page 21

BSR 2010

ITEM P 32 P 33 P 34 P 35

DESCRIPTION Supplying and fixing 1" padlock Supplying and fixing 1 1/2" padlock Supplying and fixing 2" padlock Supplying and fixing hasp & staple

UNIT No. No. No. No.

RATE 495.00 585.00 1035.00 50.00

Q - ROOFING AND CEILING
Q 01 Q 02 Q 03 Q 04 Q 05 Q 06 Roof covering with calicut pattern clay tiles. (Timber frame work and ridge covering measured separately) Roof covering with corrugated asbestos sheets. (Timber frame work and ridge covering measured separately) Asbestos close fitting ridges fixed complete with roofing screws or hook bolts. Ridging with calicut pattern tiles bedded in cement, lime & sand mortar 1:1:4 and coloured to match the tiles. One layer of half round tiles over existing corrugated sheets. 3/4" x 6" wide tongued and grooved lunumidella ceiling boards fixed to underside of existing rafters with brass screws including leveling with timber strip where necessary. Asbestos eaves ceiling with Halmilla coves & fillets. Under side to existing rafter size of fillet to be 1 1/2" x 1/2" size of cove moulding 2" x 2" Supplying and Fixing finished size 4" x 2" Coconut Rafters. Supplying and Fixing planned finished size 3 1/2 "x1 1/2" Coconut Rafters. DSI TILES ( NIVASI PRODUCT ) Item Q10 - Q14 are using for the laying of DSI ( NIVSA Tiles or approved equivelant as per the m/s Samson Rajarata Tiles (pvt)ltd. Manufactures specifications. Timber frame work sizes specified as follows. a) Ridge plate - 45mm x 190mm b) Wall plate - 117mm x 190mm c) Rafters - 45mm x 117mm maximum lengh 10'-0" @ 18" C/C Q 10 d) Reepers - 45mm x 25mm @ 10" C/C Roof covering with Natural type main tiles or approved equivelant . (Specified Timber frame work and ridge covering measured separately) Ridging with Natural type ridge tiles bedded in cement, sand mortar 1:5 and coloured to match the tiles. Sqr. 19385.00 Sqr. Sqr. L.ft. L.ft. 7825.00 6710.00 180.00 140.00

Sqr. Sqr.

16700.00 13235.00

Q 07

Sqr.

7360.00

Q 08 Q 09

L.ft. L.ft.

110.00 85.00

Q 11

L.ft.

265.00

Engineering organization, W.P.

Page 22

BSR 2010

ITEM Q 12 Q 13 Q 14

DESCRIPTION Roof covering with Natural type gable left tiles or approved equivelant . Roof covering with Natural type gable right tiles or approved equivelant . Roof covering with Natural type corner tiles or approved equivelant . Flashing

UNIT L.ft. L.ft. L.ft.

RATE 175.00 175.00 180.00

Q 15

Aluminium Valley gutter of 3'-0" wide in gauge 24 sheets including 3/4" thk. Ginisapu timber boarding finished with two coats of wood preservative. Aluminium flashing of 1'- 6" wide in gauge 24 sheets including 3/4" thk. Ginisapu timber boarding finished with two coats of wood preservative. Aluminium flashing of 1'-6" wide in gauge 24 sheets, bent to shape and fix to wall. (without timber boarding) G.I. Flashing 20 B.W.G. of 1'6" girth with end laps not less than 6" , turned and tuck up not less 6" in wall and pointed in cement motor 1:2 G.I. Valley gutter of 3'-0" wide in gauge 18 sheets including 3/4" thk. Ginisapu timber boarding including two coats of anticorrosive paint and wood preservative to sheet and boarding. (Only to be specified when repairing an existing G.I. gutter) Zincalum flashing (0.47mm thick) and 1'6" wide bent to shape and fixed to wall (without timber coating) Zincalum Valley gutter of 3'-0" wide in 0.47mm thick sheets including 3/4" thk. Ginisapu timber boarding including wood preservative boarding.

L.ft.

1195.00

Q 16

L.ft.

960.00

Q 17 Q 18

L.ft. L.ft.

290.00 390.00

Q 19

L.ft.

1400.00

Q 20 Q 21

L.ft. L.ft.

335.00 1290.00

Engineering organization, W.P.

Page 23

BSR 2010

ITEM Roof Timber Note :

DESCRIPTION

UNIT

RATE

During the past two years, Divisional Engineers have reported that exact imperial sizes on the timber on following categories are not readily available in the market, unless logs are being purchased and sawn to the exact size. Contractor's Association has also made representation indicating that the imperial size specified in the BSR is not available on imported timber varieties, and due to scarcity of the local timber, small scale Contractors are unable to purchase logs and seasoned the timber and sawn to the imperial sizes. Market survey has confirmed the same. Accordingly, it has been decided to indicate the cross sectional size roof timber in the following manner to be in par with sectional sizes readly available in the local market, as it may not be worthwhile to prescribe timber sizes and, then request Contractors to by a large section and produce it to the required size, since there is no standardization of the timber imports. This has been done to avoid subjective decision taken by the Divisional Engineers during the project implementation phase.
Accordingly, the following imperial sizes are being now replaced by the following Metric sizes. 1" to be replaced by 22mm 2” to be replaced by 45mm 3” to be replaced by 70mm 4” to be replaced by 94mm 5” to be replaced by 117mm 6” to be replaced by 140mm 7” to be replaced by 165mm 8” to be replaced by 190mm. Hence, timber will now be prescribed as 2"x 1" as 45mmx22mm 2”x 2” as 45mm x 45mm 4”x 2” as 94mm x 45mm 5”x 2” as 117mm x 45mm 5”x 3” as 117mm x 70mm 4”x 3” as 94mm x 70mm 6”x 2” as 140mm x 94mm 6”x 3” as 140mm x 70mm 6”x 4” as 140mm x 94mm 8”x 4” as 190mm x 94mm

Refer preamble note for approved timber species. The rate for timber items will remain same irrespective of timber species.

Engineering organization, W.P.

Page 24

BSR 2010

ITEM Q 22

DESCRIPTION Roof with calicut pattern tiles on local Micro (Eucalyptus Microcoris) or Balau , Bitis or Kempas timber frame work complete with ridge hips etc. comprising of 165mm x 45mm ridge plate , 94mm x 70mm wall plate , 94mm x 45mm rafters @ 18" c/c and 45mm x 22mm reepers @ 12" c/c. Rate shall include for applying of wood preservative. Roofing with asbestos corrugated sheets on local Micro (Eucalyptus Microcoris) or Balau , Bitis, or Kempas timber frame work (Ridging measured separately).Comprising of 165mm x 45mm ridge plate , 94mm x 70mm wall plate , 94mm x 45mm rafters @ 30" c/c and 45mm x 45mm battens @ 3'-0" c/c.Rate shall include for applying of wood preservative. Supply and installation of Zn/Alum profile sheets of total thickness 0.47mm , fixed to the roof timber frame work comprising of 140mm x 45mm hip rafters/valley rafters, 94mm x 70mm wall plates, 117mm x 94mm purling , 94mm x 45mm rafters @ 2'-0" spacing and 45mm x 22mm reepers @ 3'-6" spacing including ridge capping , end capping and other accessories required to complete the roof to working order. (Ceiling and thermal installation measured separately.) Rate shall include for routing , planing and sand papering hip/valley rafters, purlings and rafters and application of waterbased stain and two coats of water based sealants. Rate shall include for applying of wood preservative. Asbestos flat ceiling fixed with coves & fillets to local Micro (Eucalyptus Microcoris) or Balau , Bitis or Kempas timber frame work of 94mm x 45mm @ 4' - 0" c/c , 45mm x 45mm @ 2' - 0" c/c, fillet size to be 1 1/2" x 1/2" and cove moulding size to be 2" x 2". Rate shall include for applying of wood preservative. Asbestos flat eaves ceiling fixed with coves and fillets to local Micro (Eucalyptus Microcoris) timber work. or Balau , Bitis or Kempas.fillet size to be 1 1/2" x 1/2" cove moulding size to be 2" x 2". Rate shall include for applying of wood preservative. 3/4" thick x 6" wide tongued and grooved lunumidella ceiling boards fixed flat on 94mm x 45mm local Micro (Eucalyptus Microcoris) or Balau , Bitis or Kempas.and timber joist at every 2' - 0" c/c. cove moulding size to be 2" x 2". Rate shall include for applying of wood preservative. Supply and installation of tongued and grooved 3/4" x 6" lunumidella ceiling planks on top of rafters , with double sided aluminium foil fixed on top. Rate shall include for sand papering and smoothing one side of the planks , application of water based staining and two coats of water based sealant. Rate shall include for applying of wood preservative.

UNIT Sqr.

RATE 29740.00

Q 23

Sqr.

17815.00

Q 24

Sqr.

34945.00

Q 25

Sqr.

21260.00

Q 26

Sqr.

13725.00

Q 27

Sqr.

21665.00

Q 28

Sqr.

33400.00

Engineering organization, W.P.

Page 25

BSR 2010

ITEM Q 29

DESCRIPTION Supplying and fixing 190mm x 94mm , 165mm x 45mm , 140mm x 94mm , 140mm x 70mm , 140mm x 45mm , 117mm x 190mm and 45mm x 190mm local micro or Balau , Kempas or Bitis timber purling , hip/valley rafters etc. with applying of wood preservative. Supplying and fixing 117mm x 70mm purling up to 12'-0" length Balau, Kempas , Micro. with applying of wood preservative. Supplying and fixing 94mm x 70mm wall plates up to 12'-0" length, Balue, Kempas, Micro. with applying of wood preservative. Supplying and fixing 117mm x 70mm , 117mm x 45mm , 94mm x 70mm local Micro (Eucalyptus Microcoris) Balau , Bitis ,Kempas timber purlins, wall plates, rafters etc. with applying of wood preservative. Supplying and fixing 94mm x 45mm local Micro (Eucalyptus Microcoris) or Balau Kempas or Bitis timber purling, rafters etc. with applying of wood preservative. Supplying and fixing 45mm x 45mm local Micro (Eucalyptus Microcoris) or Balau, Kempas or Bitis timber bearers. with applying of wood preservative. Supplying and fixing 45mm x 22mmlocal micro (Eucalyptus Microcoris)or Balau, Kempas or Bitis. timber reapers with applying of wood preservative. Timber valance/barge board in GINISAPU timber finished size 9" x 3/4" thick fixed to roof frame with brass screws and applying of wood preservative. Pressure treatment of timber at an approved kiln including transport charges Applying two coats of wood preservative (Clear) to wood work. Supply and fixing 3/4"x 1/4"x12" long flat iron bracket for fixing valance board/barge board. Rate shall include for two coats of anti-corrosive paint.

UNIT Cu.ft.

RATE 5150.00

Q 30

L.ft.

320.00

Q 31

L.ft.

270.00

Q 32

Cu.ft.

3800.00

Q 33

L.ft.

195.00

Q 34

L.ft.

86.00

Q 35

L.ft.

50.00

Q 36

L.ft.

195.00

Q 37 Q 38 Q 39

Cu.ft. Sqr. No.

390.00 790.00 160.00

R - GUTTERS AND DOWN PIPES
R 01 P.V.C. eaves gutter 4 1/2" square type fixed to valance board with P.V.C. brackets @ 1' - 6" c/c including necessary mitre joints , gutter joiners , running heads & end caps. P.V.C. down pipes 3 1/2" dia. fixed to wall with P.V.C. clips @ 4'-0" c/c including necessary sockets, bends, elbows. L.ft. 180.00

R 02

L.ft.

140.00

Engineering organization, W.P.

Page 26

BSR 2010

ITEM

DESCRIPTION

UNIT

RATE

S - SANITARY FITTINGS
Note : In view of the variety of sanitary ware and fittings available in the market, it has become necessary to prescribe the exact quality requirements in terms of performance and durability aspects. The "Rocell & American Standard" brands and respective model numbers have been chosen as a bench mark to establish the said requirements. The brand name and model number appearing in the respective BSR items are purely meant to describe the performance standard of the said fitting/item and does not imply in any model that only the "Rocell & American Standard" brands are recommended or considered to be restricted to the "Rocell & American Standard" brands. Any other make/brand that has equivalent performance characteristics are considered as equivalent provided such fittings met with following criteria. Has an authorized local agent in Sri Lanka The local agent has been in the trade of the offered make for not less than 5 years. The offered sanitary fittings has a 10 Year manufacturer's warranty issued by the agent. The cistern mechanism shall have an assurance for the availability of spares for the next 3 years. The fittings are manufactured in conformity to BS, JIS, A.S.T.M., A.S. or S.L.S. standards. The dimensions are and performance characteristics are in par with the stated model. The brands that may be considered as equivalent are "Ideal" brand, or "Twyford" brand or any other approved make which prior approval to be obtained. In case where wash basin outlet directly falls on to an open drain, the bottle trap may be omitted. For wash basins fixed on open areas plastic tap of item T 07 be specified.

1

2

3

(a) (b)

(c)

(d)

(e)

(f)

4 5 (a) 5 (b)

Engineering organization, W.P.

Page 27

BSR 2010

ITEM Normal Range S 01

DESCRIPTION

UNIT

RATE

Supply and fix white vitreous china floor standing wash basin and pedestal with overflow hole and single tap hole in center of "Rocell" brand & model "Urban D" or approved equivalent complete to working order inclusive of the 1 1/4" chromium plated waste outlet of "Rocell" brand & model "A706" and 1 1/4" chromium plated siphon cleanable bottale trap of "Rocell" brand & model "A186". Supply and fix white vitreous china floor standing close coupled semi back to wall water closet suite with wash down flushing with 6/3 liters dual flushing has horizontal outlet with vario drain bend and two lateral holes for bottom water connection , cistern with water inlet from rear of "Rocell" brand & model "Urban D" or approved equivalent complete to working order inclusive of universal bend of "Rocell" brand & model "Vario Joint".

No.

14170.00

S 02

No.

17230.00

S 03

Supply and fix Chromium plated piller tap for wash basin only cold water of "American Standard" brand model No. 4604.415.50 or approved equivalent. Supply and fix Chromium plated single level wash basin mixer tap without pop-up waste with connection flex of "Rocell" brand model No.Duca - 16495 or approved equivalent with 5 year written warranty from the authorized agent. Semi - Luxuary Range

No.

2530.00

S 04

No.

6750.00

S 05

Supply and fix white vitreous china floor standing wash basin and pedestal with overflow hole and single tap hole in center of "Rocell" brand & model "Dune" or approved equivalent complete to working order inclusive of the 1 1/4" chromium plated waste outlet of "Rocell" brand & model "A706" and 1 1/4" chromium plated siphon cleanable bottale trap of "Rocell" brand & model "A186". Supply and fix white vitreous china floor standing close coupled semi back to wall water closet suite with wash down flushing with 6/3 liters dual flushing has horizontal outlet with vario drain bend and two lateral holes for bottom water connection , cistern with water inlet from rear of "Rocell" brand & model "Dune" or approved equivalent complete to working order inclusive of universal bend of "Rocell" brand & model "Vario Joint".

No.

15795.00

S 06

No.

20580.00

S 07

Supply and fix Chromium plated piller tap for wash basin only cold water of "American Standard" brand model No. 4604.415.50 or approved equivalent. Supply and fix Chromium plated single level wash basin mixer tap without pop-up waste with connection flex of "Rocell" brand model No.Duca - 16495 or approved equivalent with 5 year written warranty from the authorized agent.

No.

2530.00

S 08

No.

6750.00

Engineering organization, W.P.

Page 28

BSR 2010

ITEM Luxuary Range S 09

DESCRIPTION

UNIT

RATE

Supply and fix white vitreous china floor standing wash basin and pedestal with overflow hole and single tap hole in center of "Rocell" brand & model "Intense" or approved equivalent complete to working order inclusive of the 1 1/4" chromium plated waste outlet of "Rocell" brand & model "A706" and 1 1/4" chromium plated siphon cleanable bottale trap of "Rocell" brand & model "A186". Supply and fix white vitreous china floor standing close coupled semi back to wall water closet suite with wash down flushing with 6/3 liters dual flushing has horizontal outlet with vario drain bend and two lateral holes for bottom water connection , cistern with water inlet from rear of "Rocell" brand & model "Intense" or approved equivalent complete to working order inclusive of universal bend of "Rocell" brand & model "Vario Joint".

No.

24785.00

S 10

No.

31690.00

S 11

Supply and fix white vitreous china floor standing Bidet with overflow hole of "Rocell" brand & model "Intense" or approved equivalent complete to working order. Supply and fix Chromium plated piller tap for wash basin only cold water of "American Standard" brand model No.A-1500N or approved equivalent. Supply and fix Chromium plated single level wash basin mixer tap with pop-up waste with connection flex of "Rocell" brand model No.Sprint - 29500 or approved equivalent with 5 year written warranty from the authorized agent. Other Fittings for Normal / Semi-Luxury / Luxury

No.

17315.00

S 12

No.

12050.00

S 13

No.

17820.00

S 14

Supply and fix wall hung wash basin with half pedestal and single tap hole in center of "Rocell" brand model No."Dew Point" or approved equivalent complete to working order. Supply and fix wall hung ceramic corner wash basin of "American Standard " brand, model New Codie TF 0940 or approved equivalent complete to working order.Rate inclusive of brackets and connection to pipe line, but without tap and bottle trap. Supply and installation of vanity type wash basin of "American Standard " brand, model Ceros - TF0477 with A-8006 waste & plug or approved equivalent. On concrete vanity slab finished with 3/4" thick approved polished granite tile in black colour. ( Vanity top concrete slab & Granite tile laying measured separatly.) Supply and fix squatting pan with foot rest of "Rocell" brand model No. SP3F013 or approved equivalent.

No.

20520.00

S 15

No.

6945.00

S 16

No.

6355.00

S 17

No.

3545.00

Engineering organization, W.P.

Page 29

BSR 2010

ITEM S 18

DESCRIPTION Supply and fix low level plastic cistern for squatting pan of "Rocell" brand or approved equivalent including connecting pipe between tank and squatting pan. Supply and fix ceramic urinal with flush valve of "Rocell" brand model DP70013 or approved equivalent complete to working order. Supply and fix Chromium plated 1 1/4" dia.siphon cleanable bottale trap of "Rocell" brand model No.A186 or approved equivalent. Supply and fix Chromium plated 1/2" dia. angle valve brass fitting with zink head of "Rocell" brand model No.A280 or approved equivalent. Supply and fix hand held chromium plated bidet spray of "American Standard " brand model A4700 or approved equivalent. Supply and fix Chromium plated 4 function shower head of "American Standard" brand model No. A-6080 with shower arm of "American Standard" brand model No. A-6110-974-845 & concealed valve of "American Standard" brand model No. A7002C-B JAZZ or approved equivalent for cold water. Supply and fix Chromium plated hand shower of "American Standard" brand model No. A-2003-A-MR with adjustable shower rod with soap tray of "American Standard" brand model No. Viola 11 - A-6110-978-777 & angle valve of "American Standard" brand model No. 9113.005.50 or approved equivalent for cold water. Supply and fix Chromium plated shower level built-in-shower mixer with auto diverter shower arm jointed shower head of "Rocell" brand model No.Pony Z - Z6955 or approved equivalent. Supply and fix Chromium plated shower mixer of "American Standard" brand model No. Saga - 1512.701.50 with adjustable shower rod of "American Standard" brand model No. Viola 11 A-6110-978-777 or approved equivalent. Supply and fix service sink (Lab sink) of "American Standard " brand, model TF-8124 with A-8006 waste & plug or approved equivalent for the school building complete to working order.

UNIT No.

RATE 3470.00

S 19

No.

17230.00

S 20

No.

5045.00

S 21

No.

1425.00

S 22

No.

4945.00

S 23

No.

10275.00

S 24

No.

15400.00

S 25

No.

9015.00

S 26

No.

13070.00

S 27

No.

14115.00

S 28

Supply and fix fully chemical resistant laboratory sink of "American Standard " brand, model Larch - S594501 or approved equivalent specially for the operating theatres. Supply and fix brass chromium plated elbow operated pillar tap for the operating theatres of "American Standard " brand, model ML30 or approved equivalent.

No.

105810.00

S 29

No.

5765.00

Engineering organization, W.P.

Page 30

BSR 2010

ITEM S 30

DESCRIPTION Supply and fix automatic hand dryer of "American Standard " brand, model Kingsway - HK1800PA or approved equivalent including electrical connection. Supply and fix 5mm thick mirror of size 18" x 24" double coated with pencelage back strecher. Bathroom Accessories

UNIT No.

RATE 19750.00

S 31

No.

2465.00

S 32

Supply and fix chromium plated Soap Basket of "Rocell" brand & model "Charming" or approved equivalent. (Normal & Semiluxuary range ) Supply and fix chromium plated brass body and galss Soap Dish of "Rocell" brand & model "Charming" - DP 6703 or approved equivalent. ( Luxuary range ) Supply and fix chromium plated brass body and galss Tumbler Holder of "Rocell" brand & model "Charming" or approved equivalent. Supply and fix chromium plated Towel Ring of "Rocell" brand & model "Charming" or approved equivalent. Supply and fix chromium plated Robe Hook of "Rocell" brand & model "Charming" or approved equivalent. Supply and fix chromium plated Toilet Paper Holder of "Rocell" brand & model "Charming" or approved equivalent. Supply and fix chromium plated Toilet Cup Holder of "Rocell" brand & model "Charming" or approved equivalent. Supply and fix chromium plated 600mm long Single Towel Bar of "Rocell" brand & model "Charming" or approved equivalent. Supply and fix chromium plated 600mm long Double Towel Bars of "Rocell" brand & model "Charming" or approved equivalent. Supply and fix chromium plated 600mm long Towel Rack of "Rocell" brand & model "Charming" or approved equivalent. Supply and fix chromium plated brass body 450mm long Glass Shelf of "Rocell" brand & model "Charming" or approved equivalent. Disable Fittings & Accessories

No.

3270.00

S 33

No.

2105.00

S 34

No.

2105.00

S 35 S 36 S 37

No. No. No.

2035.00 1345.00 3075.00

S 38

No.

3395.00

S 39

No.

3770.00

S 40

No.

4615.00

S 41

No.

8600.00

S 42

No.

3310.00

S 43

Supply and fix ceramic wall hung wash basin for disabled of "American Standard " brand, model Kimera - TF995 with waste & plug A-8006 or approved equivalent.

No.

7340.00

Engineering organization, W.P.

Page 31

BSR 2010

ITEM S 44

DESCRIPTION Supply and fix white ceramic water closet suite for the disabled of "American Standard" brand & model Ventura - 3200.001.09 , Cygnet tank - PP.4041.020.03C and Seat and cover - 390000N or approved equivalent complete to working order. Supply and fix hand grip rails for disabled of "American Standard " brand, model Me-tu -MTJT26 or approved equivalent.

UNIT No.

RATE 25965.00

S 45

No.

15340.00

S 46 S 47

Supply and fix grip bar for disabled of "American Standard " brand, model Apex - AR-065-18 S/S or approved equivalent. Supply and fix hand grip-shower angle for disabled of "American Standard " brand, model Me-tu - MTJT22-5 or approved equivalent. Supply and fix hand grip-shower for disabled of "American Standard " brand, model Me-tu - MTJT22-10 or approved equivalent. Indian & Malasian Origins

No. No.

2435.00 14460.00

S 48

No.

14460.00

S 49 S 50 S 51

Supply and fix footrest squatting pan and trap including laying flush pipe laid on concrete base. (Indian Origin) Supply and fix ceramic urinal bowl with trap fixed to wall as directed with inlet and outlet connection. (Indian Origin ) Supply and fix wash basin with pedestal model no.BSWBA 620x470 VCP - manufactured by Mascon or equivalant complete to work in order. Rate without pillar tap & bottle trap. Supply and fix wall hung corner wash basin model no.BSWBA16x16CC manufactured by Mascon or equivalant complete to work in order. Rate inclusive of brackets and connection to pipe line, but without pillar tap & bottle trap. Supply and fix wash basin only with steel brackets including 1/2" angle valve and 1/2" pillar tap marketed by M/s. "Rajabdeen" or approved equivalent. ( Indian Origin ) Supply and fix low level water closet with cistern of Indian Origin with angle valve, "P" or "S" trap, all complete to working order. ( Indian Origin ) High-level plastic cistern supplied and fixed to wall rawl plug & screws complete with P.V.C. flush pipe, stop cock, water supply connection etc. (Malaysian make) Supply and fix 36" x 18" stainless steel kitchen sink with single bowl & single drain of "Sealcore" by mascons or approved equivelant with 5 year written warranty from the authorized agent. including PVC bottle trap and water connection with flexible hose, all complete to working order. ( Swan neck tap paid separately.)

No. No. No.

2560.00 2800.00 7180.00

S 52

No.

1545.00

S 53

No.

5375.00

S 54

No.

8100.00

S 55

No.

4315.00

S 56

No.

4470.00

Engineering organization, W.P.

Page 32

BSR 2010

ITEM S 57

DESCRIPTION Supply and fix 17" x 18" stainless steel kitchen sink with single bowl of "Sealcore" by mascons or approved equivelant with 5 year written warranty from the authorized agent. including PVC bottle trap and water connection with flexible hose, all complete to working order. ( Swan neck tap paid separately.) Supplying and fixing 1 1/4" (40 mm) dia. PVC Bottle Trap. (Malaysian make ) Shower rose chromium plated 4" dia. Fixed vertically with 1/2" valve socket including water connection. Supply and fixing plastic seat cover Mirror bevelled rectangular 20"x 15" with hard wood back 3/4" thickness finished with 2 coats of enamel paint. Aluminium clips and key hole hanging plate including glass shelves.

UNIT No.

RATE 3535.00

S 58 S 59 S 60 S 61

No. No.

415.00 885.00

No. No.

820.00 2240.00

T - PLUMBING
Note: All P.V.C. pipes should confirm to S.L.S. 147 T 01 T 02 T 03 T 04 T 05 T 06 Supplying laying and/or fixing 1/2" dia. P.V.C. pipes 1000 (Specials paid separately). Supplying laying and/or fixing 3/4" dia. P.V.C. pipes 1000 (Specials paid separately). Type Type L.ft. L.ft. L.ft. L.ft. L.ft. L.ft. 46.00 72.00 84.00 106.00 146.00 232.00

Supplying laying and/or fixing 1" dia. P.V.C. pipes Type 1000 (Specials paid separately). Supplying laying and/or fixing 1 1/4" dia. P.V.C. pipes Type 1000 (Specials paid separately). Supplying laying and/or fixing 1 1/2" dia. P.V.C. pipes Type 1000 (Specials paid separately). Supplying laying and/or fixing 2" dia. P.V.C. pipes Type 1000 (Specials paid separately). "Water - Tec" Brand or Approved Equivalent Fittings T 07 - T 12 ) (

T 07 T 08 T 09 T 10 T 11 T 12

Supplying and fixing 1/2" Bib tap Supplying and fixing 1/2" Angle valve Supplying and fixing 1/2" Pillar Sink tap.(Swan-neck) Supplying and fixing 1/2" Wall Sink tap. Supplying and fixing Health foucet.(Bidet Spray) Supplying and fixing Shower rose

No. No. No. No. No. No.

300.00 295.00 920.00 990.00 550.00 575.00

Engineering organization, W.P.

Page 33

BSR 2010

ITEM

DESCRIPTION "Plumber" Brand or Approved Equivalent Fittings T 13 -T17 ) (

UNIT

RATE

T 13

Supply and fixing 1/2" dia. chromium plated Concealed stop cock of "Plumber" brand & model no: NCE-0405 or approved equivalent. Supply and fixing 1/2" dia. chromium plated Angle cock of "Plumber" brand & model no: NCE-0507 or approved equivalent. Supply and fixing 1/2" dia. chromium plated Pillar cock , foam flow of "Plumber" brand & model no : NCE-0101 or approved equivalent. Supply and fixing 1/2" dia. chromium plated Bib cock , foam flow of "Plumber" brand & model no : NCE-0202 or approved equivalent. Supply and fixing 1/2" dia. chromium plated Sink cock with swivel spout deck mounted, foam flow of "Plumber" brand & model no : NCE-0202 or approved equivalent. (Swan-neck Type)

No.

1600.00

T 14

No.

925.00

T 15

No.

1580.00

T 16

No.

1335.00

T 17

No.

3400.00

T 18 T 19 T 20 T 21 T 22 T 23 T 24 T 25 T 26 T 27 T 28 T 29 T 30 T 31

Supplying and fixing 1/2" stop cock. Supplying and fixing 3/4" stop cock. Supplying and fixing 1" wheel valve "Pegler" Brand or approved equivalent. Supplying and fixing 1 1/2" wheel valve "Pegler" Brand or approved equivalent. Supplying and fixing 2" wheel valve "Pegler" Brand or approved equivalent. Supplying and fixing 1/2" Handle valve Supplying and fixing 3/4" Handle valve Supply and fixing 1" dia Brass Ball valve "Pegler" Brand or approved equivalent. Supply and fixing 3/4" dia Brass Ball valve "Pegler" Brand or approved equivalent. Supply and fixing 1/2" dia Brass Ball valve "Pegler" Brand or approved equivalent. Supply and fixing 1" dia PVC Compact Ball valve.

No. No. No. No. No. No. No. No. No. No. No. No. No. No.

535.00 860.00 1640.00 2180.00 5675.00 585.00 910.00 1770.00 1215.00 710.00 375.00 355.00 240.00 210.00

Supply and fixing 3/4" dia PVC Compact Ball valve. Supply and fixing 1/2" dia PVC Compact Ball valve. Supply and fixing 1/2" dia PVC Union.

Engineering organization, W.P.

Page 34

BSR 2010

ITEM T 32 T 33

DESCRIPTION Supply and fixing 1" dia PVC Union. Supplying and laying 4" dia.P.V.C. sewer pipes (type 600) Including cement concrete surrounding 1:3:6: ( 1") as per Drg. No:- WSS 270 - Type I . Excavation paid separately. Supplying and laying 6" dia.P.V.C. sewer pipes (type 600) Including cement concrete surrounding 1:3:6: ( 1") as per Drg. No:- WSS 270 - Type II . Excavation paid separately. Supplying and laying 4" dia.P.V.C. sewer pipes (type 600) fixed to wall and floor slab with clips. Supplying and laying 6" dia. P.V.C. sewer pipes (type 600) fixed to wall and floor slab with clips. Supplying and Fixing 1 1/4" dia P.V.C. waste pipe (type 600) Supplying and fixing 1 1/2" dia P.V.C. waste pipe (type 600) Supplying and fixing Supplying and fixing 2" dia. P.V.C waste pipe (type 600) 4" dia. P.V.C waste pipe (type 600)

UNIT No. L.ft.

RATE 230.00 885.00

T 34

L.ft.

1520.00

T 35 T 36 T 37 T 38 T 39 T 40 T 41

L.ft. L.ft.

585.00 1100.00

L.ft. L.ft. L.ft. L.ft. No.

95.00 115.00 165.00 500.00 8600.00

Supplying and installing "Plastishell" or any other water tank 500 Ltr. capacity (fittings paid separately) at an average height of 12'0". Tank shall have a 5 year warranty from the manufracture.

T 42

Supplying and installing "Plastishell" or any other water tank 1000 Ltr. capacity (fittings paid separately) at an average height of 12'-0". Tank shall have a 5 year warranty from the manufracture. Supplying and installing 2000 ltr. "Plastishell" or any other water tank at average 12 ft. height including transporting and hoisting in position Tank shall have a 5 year warranty from the manufracture. Supplying and installing 5000 ltr. "Plastishell" or any other water tank at average 12 ft. height including transporting and hoisting in position Tank shall have a 5 year warranty from the manufracture. Supplying and fixing 1/2" dia PVC Socket Supplying and fixing 1/2" dia. PVC Valve Socket Supplying and fixing 1/2" dia. PVC Faucet Socket Supplying and fixing 1/2" dia. PVC Elbow Supplying and fixing 1/2" dia. PVC Bend Supplying and fixing 1/2" dia. PVC Equal Tee

No.

15900.00

T 43

No.

27100.00

T 44

No.

63980.00

T 45 T 46 T 47 T 48 T 49 T 50

No. No. No. No. No. No.

43.00 47.00 47.00 42.00 54.00 47.00

Engineering organization, W.P.

Page 35

BSR 2010

ITEM T 51 T 52 T 53 T 54 T 55 T 56 T 57 T 58 T 59 T 60 T 61 T 62 T 63 T 64 T 65 T 66 T 67 T 68 T 69 T 70 T 71 T 72 T 73 T 74 T 75 T 76 T 77

DESCRIPTION Supplying and fixing 1/2" dia. PVC Clips Supplying and fixing 3/4" dia PVC Socket Supplying and fixing 3/4" dia. PVC Valve Socket Supplying and fixing 3/4" dia. PVC Faucet Socket Supplying and fixing 3/4" dia. PVC Elbow Supplying and fixing 3/4" dia. PVC Bend Supplying and fixing 3/4" dia. PVC Equal Tee Supplying and fixing 3/4" dia. PVC Clips Supplying and fixing 1" dia PVC Socket Supplying and fixing 1" dia. PVC Valve Socket Supplying and fixing 1" dia. PVC Faucet Socket Supplying and fixing 1" dia. PVC Elbow Supplying and fixing 1" dia. PVC Bend Supplying and fixing 1" dia. PVC Equal Tee Supplying and fixing 1" dia. PVC Clips Supplying and fixing 1 1/4" dia PVC Socket Supplying and fixing 1 1/4" dia. PVC Valve Socket Supplying and fixing 1 1/4" dia. PVC Faucet Socket Supplying and fixing 1 1/4" dia. PVC Elbow Supplying and fixing 1 1/4" dia. PVC Bend Supplying and fixing 1 1/4" dia. PVC Equal Tee Supplying and fixing 1 1/4" dia. PVC Clips Supplying and fixing 1 1/2" dia PVC Socket Supplying and fixing 1 1/2" dia. PVC Valve Socket Supplying and fixing 1 1/2" dia. PVC Faucet Socket Supplying and fixing 1 1/2" dia. PVC Elbow Supplying and fixing 1 1/2" dia. PVC Bend

UNIT No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No.

RATE 21.00 52.00 57.00 57.00 57.00 65.00 65.00 27.00 66.00 64.00 67.00 72.00 83.00 88.00 28.00 87.00 96.00 104.00 103.00 150.00 125.00 30.00 123.00 126.00 136.00 157.00 228.00

Engineering organization, W.P.

Page 36

BSR 2010

ITEM T 78 T 79 T 80 T 81 T 82 T 83 T 84 T 85 T 86 T 87 T 88 T 89 T 90 T 91 T 92 T 93 T 94 T 95 T 96 T 97 T 98 T 99 T 100 T 101 T 102 T 103 T 104

DESCRIPTION Supplying and fixing 1 1/2" dia. PVC Equal Tee Supplying and fixing 1 1/2" dia. PVC Clips Supplying and fixing 2" dia PVC Socket Supplying and fixing 2" dia. PVC Valve Socket Supplying and fixing 2" dia. PVC Faucet Socket Supplying and fixing 2" dia. PVC Elbow Supplying and fixing 2" dia. PVC Bend Supplying and fixing 2" dia. PVC Equal Tee Supplying and fixing 2" dia. PVC Clips Supplying and fixing 2 1/2" dia PVC Socket Supplying and fixing 2 1/2" dia. PVC Valve Socket Supplying and fixing 2 1/2" dia. PVC Faucet Socket Supplying and fixing 2 1/2" dia. PVC Elbow Supplying and fixing 2 1/2" dia. PVC Bend Supplying and fixing 2 1/2" dia. PVC Equal Tee Supplying and fixing 2 1/2" dia. PVC Clips Supplying and fixing 3" dia PVC Socket Supplying and fixing 3" dia. PVC Valve Socket Supplying and fixing 3" dia. PVC Faucet Socket Supplying and fixing 3" dia. PVC Elbow Supplying and fixing 3" dia. PVC Bend Supplying and fixing 3" dia. PVC Equal Tee Supplying and fixing 3" dia. PVC Clips Supplying and fixing 2" - 1 1/2" dia. PVC. Reducing Socket Supplying and fixing 2" - 1 1/4" dia. PVC. Reducing Socket Supplying and fixing 2" - 1" 1/2 dia. PVC. Reducing Socket Supplying and fixing 2" - 3/4" 2 dia. PVC. Reducing Socket

UNIT No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No.

RATE 205.00 36.00 177.00 190.00 195.00 243.00 395.00 297.00 38.00 378.00 1125.00 356.00 795.00 925.00 1015.00 41.00 540.00 1150.00 645.00 1425.00 1520.00 1720.00 94.00 151.00 147.00 143.00 139.00

Engineering organization, W.P.

Page 37

BSR 2010

ITEM T 105 T 106 T 107 T 108 T 109 T 110 T 111 T 112 T 113 T 114 T 115 T 116 T 117 T 118 T 119 T 120 T 121 T 122 T 123 T 124 T 125 T 126 T 127 T 128 T 129 T 130 T 131

DESCRIPTION Supplying and fixing 2" - 1/2" 2 dia. PVC. Reducing Socket Supplying and fixing 1 1/2" - 1 1/4" dia. PVC. Reducing Socket Supplying and fixing 1 1/2" - 1" 1/2 dia. PVC. Reducing Socket Supplying and fixing 1 1/2" - 3/4" 2 dia. PVC. Reducing Socket Supplying and fixing 1 1/2" - 1/2" 2 dia. PVC. Reducing Socket Supplying and fixing 1 1/4" - 1" 1/2 dia. PVC. Reducing Socket Supplying and fixing 1 1/4" - 3/4" 2 dia. PVC. Reducing Socket Supplying and fixing 1 1/4" - 1/2" 2 dia. PVC. Reducing Socket Supplying and fixing 1" - 3/4" 2 dia. PVC. Reducing Socket Supplying and fixing 1" - 1/2" 2 dia. PVC. Reducing Socket Supplying and fixing 3/4" - 1/2" dia. PVC. Reducing Socket Supplying and fixing 2" - 1 1/2" dia. PVC. Reducing Tee. Supplying and fixing 2" - 1 1/4" dia. PVC. Reducing Tee. Supplying and fixing 2" - 1" 1/2 dia. PVC. Reducing Tee. Supplying and fixing 2" - 3/4" 2 dia. PVC. Reducing Tee. Supplying and fixing 2" - 1/2" 2 dia. PVC. Reducing Tee. Supplying and fixing 1 1/2" - 1 1/4" dia. PVC. Reducing Tee. Supplying and fixing 1 1/2" - 1" 1/2 dia. PVC. Reducing Tee. Supplying and fixing 1 1/2" - 3/4" 2 dia. PVC. Reducing Tee. Supplying and fixing 1 1/2" - 1/2" 2 dia. PVC. Reducing Tee. Supplying and fixing 1 1/4" - 1" 1/2 dia. PVC. Reducing Tee. Supplying and fixing 1 1/4" - 3/4" 2 dia. PVC. Reducing Tee. Supplying and fixing 1 1/4" - 1/2" 2 dia. PVC. Reducing Tee. Supplying and fixing 1" - 3/4" 2 dia. PVC. Reducing Tee. Supplying and fixing 1" - 1/2" 2 dia. PVC. Reducing Tee. Supplying and fixing 3/4" - 1/2" dia. PVC. Reducing Tee. Supplying and fixing 1" - 3/4" 2 dia. PVC. Reducing Foucet Tee.

UNIT No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No.

RATE 135.00 118.00 115.00 101.00 93.00 90.00 83.00 76.00 66.00 59.00 52.00 290.00 282.00 280.00 279.00 270.00 184.00 165.00 156.00 138.00 125.00 120.00 99.00 89.00 83.00 70.00 90.00

Engineering organization, W.P.

Page 38

BSR 2010

ITEM T 132 T 133 T 134 T 135 T 136 T 137 T 138

DESCRIPTION Supplying and fixing 1" - 1/2" 2 dia. PVC. Reducing Foucet Tee. Supplying and fixing 3/4" - 1/2" dia. PVC. Reducing Foucet Tee. Supplying and fixing 1" - 3/4" 2 dia. PVC. Reducing Elbow. Supplying and fixing 1" - 1/2" 2 dia. PVC. Reducing Elbow. Supplying and fixing 3/4" - 1/2" dia. PVC. Reducing Elbow. Supply and fixing 1/2" dia flexible hose - 12" length. Supply and fixing 1/2" dia flexible hose - 18" length. Special Pipe fittings All Special Pipe fittings should be "Anton" Brand or approved equivalent.

UNIT No. No. No. No. No. No. No.

RATE 76.00 78.00 84.00 78.00 75.00 480.00 555.00

T 139 T 140

Supplying and fixing 4" (110 mm) dia. Double access branch with cleaning eye. Supplying and fixing 4" (110 mm) dia Single access branch with cleaning eye. Supplying and fixing 4" (110 mm) dia single branch. Supplying and fixing 4" (110 mm) dia Swept bend with cleaning eye. Supplying and fixing 4" (110 mm) dia Swept bend. Supplying and fixing 4" (110 mm) dia Swept tee with cleaning eye. Supplying and fixing 4" (110 mm) dia Swept tee. Supplying and fixing 4" (110 mm) dia " P " trap. Supplying and fixing 4" (110 mm) dia " S " trap. Supplying and fixing 4" (110 mm) Multi floor trap. Supplying and fixing 4" (110 mm) dia Tee with cleaning eye. Supplying and fixing 4" (110 mm) dia.Bend. Supplying and fixing 6" (160mm) dia. Bend. Supplying and fixing Reducing Tee 6" x 4" (160mm x 110mm) Supplying and fixing 1 1/2" (50 mm) dia Swept tee with cleaning eye. Supplying and fixing 1 1/2" (50 mm) dia Swept tee.

No. No.

1555.00 1085.00

T 141 T 142

No. No.

920.00 1005.00

T 143 T 144

No. No.

1000.00 1140.00

T 145 T 146 T 147 T 148 T 149 T 150 T 151 T 152 T 153

No. No. No. No. No. No. No. No. No.

735.00 970.00 1280.00 655.00 895.00 740.00 955.00 1660.00 460.00

T 154

No.

460.00

Engineering organization, W.P.

Page 39

BSR 2010

ITEM T 155 T 156

DESCRIPTION Supplying and fixing 1 1/2" (50 mm) dia Equal tee. Supplying and fixing 1 1/2" (50 mm) dia Bend with cleaning eye.

UNIT No. No.

RATE 415.00 390.00

Hot water Pipes & Fittings T 157 T 158 Supplying , laying and/or fixing 1/2" dia. CPVC - SDR pipes. (Specials paid separately). Supplying , laying and/or fixing 1" dia. CPVC - SDR pipes. (Specials paid separately). Supplying and fixing 1/2" dia. CPVC Socket. Supplying and fixing 1" dia. CPVC Socket. Supplying and fixing 1/2" dia. CPVC Valve Socket. Supplying and fixing 1" dia. CPVC Valve Socket. Supplying and fixing 1/2" dia. CPVC Faucet Socket. Supplying and fixing 1" dia. CPVC Faucet Socket. Supplying and fixing 1/2" dia. CPVC Tee. Supplying and fixing 1" dia. CPVC Tee. Supplying and fixing CPVC Elbow 1/2" x 45o Supplying and fixing CPVC Elbow 1/2" x 90o Supplying and fixing CPVC Elbow 1" x 45o Supplying and fixing CPVC Elbow 1" x 90
o

L.ft. L.ft.

105.00 180.00

T 159 T 160 T 161 T 162 T 163 T 164 T 165 T 166 T 167 T 168 T 169 T 170 T 171 T 172 T 173 T 174 T 175 T 176 T 177 T 178 T 179 T 180

No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No.

60.00 300.00 70.00 318.00 92.00 395.00 92.00 560.00 76.00 76.00 505.00 435.00 270.00 485.00 56.00 210.00 810.00 645.00 725.00 875.00 460.00 695.00

Supplying and fixing CPVC Reducing Socket 1" x 1/2" Supplying and fixing CPVC Reducing Tee 1" x 1/2" Supplying and fixing 1/2" dia. CPVC End Cap. Supplying and fixing 1" dia. CPVC End Cap. Supplying and fixing 1/2" dia. CPVC Tap End Plug. Supplying and fixing 1/2" dia. CPVC Union. Supplying and fixing 1/2" dia. CPVC Elbow Holder. Supplying and fixing 1" dia. CPVC Elbow Holder. Supplying and fixing 1/2" dia. CPVC Brass Male Adapter. Supplying and fixing 1/2" dia. CPVC Brass Female Adapter.

Engineering organization, W.P.

Page 40

BSR 2010

ITEM T 181

DESCRIPTION Supplying and fixing 1/2" dia. CPVC Brass Elbow. Water Pump

UNIT No.

RATE 625.00

T 182

Supplying and fixing water pump single phase manufactured by " Jinasena" Model no:- N110T/1 ,size 1" x 1" , 0.75 H.P. , total head 80'-0" , out put 1000 I.g/hr. as per manufacturer's specifications. Rate include for fixing 1" dia. Foot valve approved make, Positioning and mount the pump on a concrete bed 9" x 9" x 3" thick in 1:2:4(3/4") with 10mm dia. hexagonal bolts to required lengh , Nuts & Washers 1/16" thick complete in working order using necessary P.V.C. pipes, specials...etc. & electrical supply from the closest DB. Pipes , specials & electricity connection paid separatly. Test

No.

19625.00

T 183 T 184

Water Pressure testing for PVC pipes. Testing of Water tanks & Sumps as per clause 3.8.6 of SCA/4/11

Item Item

1000.00 4000.00

U - DRAINAGE Waste Water Manhole - Brick
U 01 Construction of waste water brick manhole internal size of 1'-0" x 1'-0" & depth upto 1'-3", consist of 3" thick Grade 15 concrete base and 4 1/2" thick brick masonry side walls in 1:3 cement sand mix , 1/2" thick cement rendering in 1:2 to internal & external exposed faces of walls finished smooth with neat cement floating, with 2" thick Grade 20 RCC cover slab with 6mm dia. M.S. rods @ 4" c/c both ways. Rate to include for excavation, necessary formwork , lifting hooks & 3" thick concrete pad as per Drawing No:-WSS/10/01 Construction of waste water brick manhole internal size of 1'-3" x 1'-3" & depth upto 2'-0", consist of 3" thick Grade 15 concrete base and 4 1/2" thick brick masonry side walls in 1:3 cement sand mix , 1/2" thick cement rendering in 1:2 to internal & external exposed surfaces of walls finished smooth with neat cement floatings, with 2" thick Grade 20 RCC cover slab with 6mm dia. M.S. rods @ 4" c/c both ways. Rate to include for excavation, necessary formwork , lifting hooks & 3" thick concrete pad as per Drawing No:- WSS/10/01 No. 1890.00

U 02

No.

3015.00

Engineering organization, W.P.

Page 41

BSR 2010

ITEM U 03

DESCRIPTION Construction of waste water brick manhole internal size of 1'-6" x 1'-6" & depth 2'-0"to 3'-0", consist of 3" thick Grade 15 concrete base and 4 1/2" thick brick masonry side walls in 1:3 cement sand mix , 1/2" thick cement rendering in 1:2 to internal & external exposed surfaces of walls finished smooth with neat cement floatings, with 3" thick Grade 20 RCC cover slab with 10mm dia.tor steel @ 6" c/c both ways. Rate to include for excavation, necessary formwork, lifting hooks & 6" thick concrete pad as per Drawing No:-WSS/10/01 Construction of waste water brick manhole internal size of 2'-0" x 2'-0" & depth vary from 2'-0"-3'-0", consist of 4" thick Grade 15 concrete base and 9" thick brick masonry side walls in 1:3 cement sand mix ,1/2" thick cement sand rendering in 1:2 to all internal surfaces and external exposed surfaces of walls finished smooth with neat cement floating , with 3" thick Grade 20 RCC cover slab with 10mm dia. tor steel @ 6" c/c both ways.Rate to include for excavation, necessary formwork, lifting hooks and 6" thick concrete pad as per Drawing No:- WSS/10/01

UNIT No.

RATE 4700.00

U 04

No.

11585.00

Waste Water Manhole - Concrete
U 05 Construction of waste water concrete manhole internal size of 1'0" x 1'-0" & depth up to 1'-3", consist of 4" thick Grade 20 concrete base and sides ,with 2" thick Grade 20 RCC cover slab with 6mm dia.M.S. rods @ 4" c/c both ways. Rate to include for excavation, necessary formwork, lifting hooks and 1/2" thick cement sand rendering in 1:2 mix trowel smooth with neat grey cement to all internal surfaces and external exposed surfaces as per Drawing No:-WSS/10/02 Construction of waste water concrete manhole internal size of 1'3" x 1'-3" & depth up to 2'-0", consist of 4" thick Grade 20 concrete base and sides ,with 2" thick Grade 20 RCC cover slab with 6mm dia.M.S. rods @ 4" c/c both ways. Rate to include for excavation, necessary formwork, lifting hooks and 1/2" thick cement sand rendering in 1:2 mix trowel smooth with neat grey cement to all internal surfaces and external exposed surfaces as per Drawing No:-WSS/10/02 Construction of waste water concrete manhole internal size of 1'6" x 1'-6" & depth vary from 2'-0' - 3'-0", consist of 3" thick Grade15 lean concrete & 5" thick Grade 20 RCC base and side walls with 10mm dia.tor steel @ 6" c/c both ways and 3" thick Grade 20 RCC cover slab with 10mm dia. tor steel @ 6" c/c both ways. Rate to include for excavation, necessary formwork, lifting hooks and 1/2" thick cement & sand rendering in 1:2 mix trowel smooth with neat grey cement to all internal surfaces and external exposed surfaces as per Drawing No:- WSS/10/02 No. 2610.00

U 06

No.

3390.00

U 07

No.

11475.00

Engineering organization, W.P.

Page 42

BSR 2010

ITEM

DESCRIPTION

UNIT

RATE

Sewer Manhole - Brick
U 08 Construction of brick sewer manhole internal size of 2'-1" x 1'-7" & depth vary from 1'-6" - 3'-0", consist of 6" thick Grade 15 lean concrete base and 9" thick brick masonry side walls in 1:3 cement sand mix ,with 3" thick Grade 20 RCC cover slab with 10mm dia.tor steel @ 6" c/c both ways.Rate to include for excavation, necessary formwork, lifting hooks, concrete pad and 1/2" thick cement & sand rendering in 1:2 mix trowel smooth with neat grey cement to all internal surfaces , exposed external surfaces and forming channel with 1:6 benching as per Drawing No:WSS/10/03 Construction of brick sewer manhole internal size of 2'-6" x 1'-7" & depth vary from 2'-0" - 3'-0", consist of 6" thick Grade 15 lean concrete base and 9" thick brick masonry side walls in 1:3 cement sand mix ,with 3" thick Grade 20 RCC cover slab with 10mm dia.tor steel @ 6" c/c both ways. Rate to include for excavation, necessary formwork, lifting hooks , concrete pad and 1/2" thick cement & sand rendering in 1:2 mix trowel smooth with neat grey cement to all internal surfaces , exposed external surfaces and forming channel with 1:6 benching as per Drawing No:WSS/10/03 Construction of brick sewer manhole internal size of 3'-4 1/2" x 2'3" & depth vary from 2'-0" - 3'-0", consist of 6" thick Grade 15 lean concrete base and 9" thick brick masonery side walls in 1:3 cement sand mix ,with 3" thick Grade 20 RCC cover slab with 10mm dia.tor steel @ 6" c/c both ways.Rate to include for excavation, necessary formwork, lifting hooks , concrete pad and 1/2" thick cement & sand rendering in 1:2 mix trowel smooth with neat grey cement to all internal surfaces , exposed external surfaces and forming channel with 1:6 benching as per Drawing No:- WSS/10/04 Construction of brick sewer manhole internal size of 4'-6" x 2'-7 1/2" & depth vary from 2'-0" - 3'-0", consist of 6" thick Grade 15 lean concrete base and 9" thick brick masonry side walls in 1:3 cement sand mix ,with 3" thick Grade 20 RCC cover slab with 10mm dia.tor steel @ 6" c/c both ways.Rate to include for excavation, necessary formwork, lifting hooks, concrete pad and 1/2" thick cement & sand rendering in 1:2 mix trowel smooth with neat grey cement to all internal surfaces , exposed external surfaces and forming channel with 1:6 benching as per Drawing No:- WSS/10/05 No. 10705.00

U 09

No.

12840.00

U 10

No.

17870.00

U 11

No.

23115.00

Engineering organization, W.P.

Page 43

BSR 2010

ITEM U 12

DESCRIPTION Construction of brick sewer manhole internal size of 4'-6" x 2'-7 1/2" & depth vary from 3'-0" - 5'-0", consist of 6" thick Grade 15 lean concrete base and 9" thick brick masonery side walls in 1:3 cement sand mix ,with 3" thick Grade 20 RCC cover slab with 10mm dia.tor steel @ 6" c/c both ways.Rate to include for excavation, necessary formwork, lifting hooks, concrete pad and 1/2" thick cement & sand rendering in 1:2 mix trowel smooth with neat grey cement to all internal surfaces , exposed external surfaces and forming channel with 1:6 benching as per Drawing No:- WSS/10/05 Construction of brick Interceptor manhole internal size4'-6"x 2'-7 1/2" depth up to 5'-6" Consists of 3" thick grade 15 lean concrete & 6" thick Grade 20 conrete base , 9" thick brick masonry side walls in 1:3 cement sand mix ,with 3" thick Grade 20 RCC cover slab with 10mm dia.tor steel @ 6" c/c both ways.Rate to include for excavation, necessary formwork, lifting hooks concrete pad and 1/2" thick cement & sand rendering in 1:2 mix trowel smooth with neat grey cement to all internal surfaces , exposed external surfaces including interceptor with stopper and forming channels with 1:6 benching including working spaces as per Drawing No:- WSS/10/06

UNIT No.

RATE 29085.00

U 13

No.

39375.00

U 14

Construction of brick drop manhole internal size 4'-6"x 2'-7 1/2" and depth up to 5'-0", Consists of 6" thick Grade 20 conrete base with 10mm dia. tor steel @ 8" c/c bothways on 3"thick Grade 15 lean concrete and 9" thick brick masonry side walls in 1:3 cement sand mix ,with 3" thick Grade 20 RCC cover slab with 10mm dia. tor steel @ 6" c/c both ways. Rate to include for excavation, necessary formwork, lifting hooks , concrete pad and 1/2" thick cement & sand rendering in 1:2 mix trowel smooth with neat grey cement to all internal surfaces , exposed external surfaces and forming channels with 1:6 benching including P.V.C. specials , M.S. foot steps & working spaces as per Drawing No:WSS/10/07 Construction of brick drop manhole internal size 4'-6"x 2'-7 1/2" and depth vary from 5'-0" - 10'-0", Consists of 6" thick Grade 20 conrete base with 10mm dia. tor steel @ 8" c/c bothways on 3"thick Grade 15lean concrete and 9" thick brick masonery side walls in 1:3 cement sand mix ,with 3" thick Grade 20 RCC cover slab with 10mm dia.tor steel @ 6" c/c both ways.Rate to include for excavation, necessary formwork, lifting hooks , concrete pad and 1/2" thick cement & sand rendering in 1:2 mix trowel smooth with neat grey cement to all internal surfaces , exposed external surfaces and forming channel with 1:6 benching including P.V.C. specials, M.S. foot step & working spaceas per Drawing No:WSS/10/07

No.

30955.00

U 15

No.

45780.00

Engineering organization, W.P.

Page 44

BSR 2010

ITEM

DESCRIPTION

UNIT

RATE

Sewer Manhole - Concrete
U 16 Construction of RCC sewer manhole internal size of 2'-1" x 1'-7" & depth up to 2'-0", consist of 2" thick Grade 15 lean concrete and 6" thick Grade 20 concrete base and side walls r/f with 10mm dia. tor steel @ 8" c/c bothways , with 3" thick Grade 20 RCC cover slab with 10mm dia.tor steel @ 6" c/c both ways.Rate to include for excavation, necessary formwork, lifting hooks and 1/2" thick cement & sand rendering in 1:2 mix trowel smooth with neat grey cement to all internal surfaces , exposed external surfaces and forming channel with 1:6 benching.as per Drawing No:- .WSS/10/08 Construction of RCC sewer manhole internal size of 2'-6" x 1'-7" & depth vary from 2'-0" - 3'-0" , consist of 2" thick Grade 15 lean concrete and 6" thick Grade 20 concrete base and side walls r/f with 10mm dia. tor steel @ 8" c/c bothways , with 3" thick Grade 20 RCC cover slab with 10mm dia.tor steel @ 6" c/c both ways. Rate to include for excavation, necessary formwork, lifting hooks and 1/2" thick cement , sand rendering in 1:2 mix trowel smooth with neat grey cement to all internal surfaces , exposed external surfaces and forming channel with 1:6 benching as per Drawing No:- WSS/10/08 No. 15290.00

U 17

No.

17880.00

U 18

Construction of RCC sewer manhole internal size of 3'-4 1/2" x 2'3" & depth vary from 2'-0" - 3'-0" , consist of 2" thick Grade 15 lean concrete and 6" thick Grade 20 concrete base and side walls r/f with 10mm dia. tor steel @ 8" c/c bothways , with 3" thick Grade 20 RCC cover slab with 10mm dia.tor steel @ 6" c/c both ways.Rate to include for excavation, necessary formwork, lifting hooks and 1/2" thick cement , sand rendering in 1:2 mix trowel smooth with neat grey cement to all internal surfaces , exposed external surfaces and forming channel with 1:6 benching as per Drawing No:-WSS/10/09

No.

27000.00

U 19

Construction of RCC sewer manhole internal size of 4'-6" x 2'-7 1/2" & depth vary fro0m 2'-0" - 3'-0" , consist of 2" thick Grade 15 lean concrete and 6" thick Grade 20 concrete base and side walls r/f with 10mm dia. tor steel @ 8" c/c bothways , with 3" thick Grade 20 RCC cover slab with 10mm dia.tor steel @ 6" c/c both ways.Rate to include for excavation, necessary formwork, lifting hooks and 1/2" thick cement & sand rendering in 1:2 mix trowel smooth with neat grey cement to all internal surfaces , exposed external surfaces and forming channel with 1:6 benching as per Drawing No:-WSS/10/08

No.

33950.00

Engineering organization, W.P.

Page 45

BSR 2010

ITEM U 20

DESCRIPTION Construction of RCC sewer manhole internal size of 4'-6" x 2'-7 1/2" & depth vary from 3'-0" - 5'-0" , consist of 2" thick Grade 15 lean concrete and 6" thick Grade 20 concrete base and side walls r/f with 10mm dia. tor steel @ 8" c/c bothways , with 3" thick Grade 20 RCC cover slab with 10mm dia.tor steel @ 6" c/c both ways.Rate to include for excavation, necessary formwork, lifting hooks and 1/2" thick cement , sand rendering in 1:2 mix trowel smooth with neat grey cement to all internal surfaces , exposed external surfaces and forming channel with 1:6 benching as per Drawing No:- WSS/10/10

UNIT No.

RATE 45780.00

Manhole Covers
U 21 RCC Manhole cover size of 2'-0" x 2'-0" approx. & 3" thick Consist of 1:2:4(3/4") concrete & 10mm dia. Tor steel bars @ 6" C/C both ways. Rate include necessary formwork and lifting hooks. Supplying & fixing heavy duty Cast Iron manhole cover size of 24" x 18" including cover frame. Sq.ft. 505.00

U 22

No.

6570.00

Gulleys
U 23 U 24 Gulley S.W. 4" supplied and fixed including 1:2:4(3/4")concrete gully box. Construction of gully internal size of 1'-2" x 1'-2" & depth up to 1'-4" , consist of 3" thick Grade 20 concrete base and 4 1/2" thick brick masonary side walls in 1:3 cement sand mix , with 2" thick Grade 20 RCC cover slab with 6mm dia.M S rods @ 4" c/c both ways.Rate to include for excavation, necessary formwork, lifting hooks,,supplying P.V.C.gully trap infill with grade 20 concreate and 1/2" thick cement & sand rendering in 1:2 mix trowel smooth with neat grey cement to all internal surfaces , exposed external surfaces and forming channel with 1:6 benching as per Drawing No:-WSS/10/11 No. No. 1580.00 3630.00

Soakage Pits
U 25 U 26 U 27 U 28 U 29 U 30 Construction of 4'-0" dia. soakage pit in hard soil.. as per Drawing No:- WSS/SP/01 Construction of 6'-0" dia. soakage pit in hard soil. as per Drawing No:- WSS/SP/02 Construction of 8'-0" dia. soakage pit in hard soil. as per Drawing No:- WSS/SP/03 Construction of 4'-0" dia. soakage pit in loose soil.. as per Drawing No:- WSS/SP/04 Construction of 6'-0" dia. soakage pit in loose soil. as per Drawing No:- WSS/SP/05 Construction of 8'-0" dia. soakage pit in loose soil. as per Drawing No:- WSS/SP/06 No. No. No. No. No. No. 22490.00 41425.00 57570.00 52370.00 83055.00 112040.00

Engineering organization, W.P.

Page 46

BSR 2010

ITEM

DESCRIPTION

UNIT

RATE

Septic tanks
U 31 U 32 U 33 U 34 U 35 U 36 U 37 U 38 Construction of 30 person Septic tank (Brick) in hard soil. as per Drawing No:- WSS/ST/01 Construction of 50 person Septic tank (Brick) in hard soil. as per Drawing No:- WSS/ST/01 Construction of 70 person Septic tank (Brick) in hard soil. as per Drawing No:- WSS/ST/02 Construction of 100 person Septic tank (Brick) in hard soil. as per Drawing No:- WSS/ST/01 Construction of 150 person Septic tank (Brick) in hard soil. as per Drawing No:- WSS/ST/02 Construction of 100 person RCC Septic tank in hard/loose soil. as per Drawing No:-WSS/ST/03 Construction of 150 person RCC Septic tank in hard/loose soil. as per Drawing No:- WSS/ST/04 Supplying and fixing 4'-0" dia.x 8'-0" Pre-cast Septic tank (manufactured by SEC) including excavation depth not exeeding 8'-0" and Rate shall include a sand fill upto 2'-0" hight sorrounding the tank. Supplying and fixing 3'-0" internal dia.x 4'-0" depth & 3" thick walls, Pre-cast Soakage pit with perporated holes including necessary excavation including working space and 6" thick rubble packing sorrounding the tank. Rate shall include hire charges of boomtruck for placing and subject to specified approved by the Divisional Engineer. No. No. No. No. No. No. No. No. 120480.00 140695.00 158490.00 192800.00 251945.00 393060.00 497200.00 43130.00

U 39

No.

24260.00

V - ELECTRICAL INSTALLATION.
Note: Work shall be done in accordance with specifications for electrical and mechanical works(ICTAD Publication No.SCA/8 of Nov.1987 Internal lighting wiring shall comply with the drawings and shall be in 230/440 volt single core PVC insulated copper cables All switches and socket outlets shall be plated type "Clipsal", " Orange"or Cabtree make. All Fluorescent fittings of powder coated gauge 24 GI should be complete with choke (Make:-"Atco","BG" original or Equivalent) starter and the tube should be Thron, Philips, or Osram All ceiling fans should be KDK, National, Mitsubishi, Hittachi (Original Japan)with guarantee card from the authorized dealer.

1

2

3

4

Engineering organization, W.P.

Page 47

BSR 2010

ITEM

DESCRIPTION Rate to include switch boxes, plugs, round or square blocks, Chromium plated M.S. chains, brass hooks, ceiling roses, holders (angle batten and ordinary battens) and any other item necessary. All distribution boards should be incorporated with multi 9 genuine Merlin Gerin, A.B.B. , Hager, F & G , clipsal make MCB's ( Miniature circuit Breaker ) and cabtree, F & G, Clipsal , Merlin Gerin make R.C.C.B.'s (Residual Current circuit Breaker) and Terrasaki, Merlin Gerin, , Dormans Smith ,Biticano , Clockner moeller make M.C.C.B.'s (Moulded Case Circuit Breakers) The whole installation shall be carried out according to CEB/IEE wiring regulations. All the M.C.C.B.'s for the distribution boards should be purchased from the following authorized agents or from their dealers and a certificate or invoice along with their Company seal and Part No., numbers should be produced at the time of payment. Type 1. Merlin Gerin M.C.C.B.'s 2. F & G, M.C.B.'s and R.C.C.B.'s 3. Terrasaki M.C.C.B.'s 4. Cabtree R.C.C.B.'s 5. Moeller MCB,MCCB,RCCB Electrical (Pvt) Ltd. 6. Orange,Switches and Socket outlet . Agent Figaro Ltd. Rotex Ltd. Rotex Ltd. Nawaloka Ltd. Richardson .

UNIT

RATE

5

6

7

8

OS Projects (Pvt) Ltd. .

7. Steel Enclosures Rotax Ltd./ Magline Ltd. / Figaro Ltd./MSS(Pvt) Ltd. 9 10 11 The height of the light bracket from floor level is 2.5m Height of the switches from floor level is 1.5m

No ceiling fan should be installed at a height of less than 2.7m from floor level The distance of a light source from the wall should be equal to one half the distance between two adjacent light sources and also the distance between light fittings should not exceed 1.5 times the Mounting height.

12

Engineering organization, W.P.

Page 48

BSR 2010

ITEM

DESCRIPTION

UNIT

RATE

13

Point wiring only with and including switches (Rate includes wiring from MCB through switch to lamp point and includes the switch, switch box, lamp holder wire and conduit) Light point wired through a 5Amp one gang one way plate switch using 2x1/1.13(2x1/044) P.V.C. insulated copper wire in fully concealed/surface P.V.C. conduits. Light points wired through a 5 Amp two gang one way plate switch using 2x1/1.13 (2x1/044) P.V.C. insulated copper wire in fully concealed/surface P.V.C. conduits. Light points wired through a 5 Amp three gang one way plate switch using 2x1/1.13 (2x1/044) P.V.C. insulated copper wire in fully concealed/surface P.V.C. conduits. Light points wired through a 5 Amp four gang one way plate switch using 2x1/1.13 (2x1/044) P.V.C. insulated copper wire in fully concealed/surface P.V.C. conduits. Light points-wired through a 5Amp 5 gang one way plate switch using 2x1/1.13 (2x1/044) P.V.C. insulated copper wire in fully concealed/surface P.V.C. conduits. Light point wired through a 5Amp one gang two way plate switch using 2x1/1.13 (2x1/044) P.V.C. insulated copper wire in fully concealed/surface P.V.C. conduits. Light point wired through a 5 Amp one gang one way plate switch using 2x1/1.13(2x1/044) P.V.C. insulated copper wire in fully surface plastic casing and capping. Light points wired through a 5 Amp two gang one way plate switch using 2x1/1.13(2x1/044) P.V.C. insulated copper wire in fully surface plastic casing and capping. Light points wired through a 5 Amp three gang one way plate switch using 2x1/1.13(2x1/044) P.V.C. insulated copper wire in fully surface plastic casing and capping. Light points wired through a 5 Amp four gang one way plate switch using 2x1/1.13(2x1/044) P.V.C. insulated copper wire in fully surface plastic casing and capping. Light points wired through a 5 Amp. 5 gang one way plate switch using 2x1/1.13(2x1/044) P.V.C. insulated copper wire in fully surface plastic casing and capping. Light point wired through a 5Amp one gang two way plate switch using 2x1/1.13(2x1/044) P.V.C. insulated copper wire in fully surface plastic casing and capping. Per Point 1230.00

V 01

V 02

Per Point

1845.00

V 03

Per Point

2460.00

V 04

Per Point

3060.00

V 05

Per Point

3665.00

V 06

Per Point

1370.00

V 07

Per Point

1915.00

V 08

Per Point

2530.00

V 09

Per Point

3150.00

V 10

Per Point

3770.00

V 11

Per Point

4355.00

V 12

Per Point

2750.00

Engineering organization, W.P.

Page 49

BSR 2010

ITEM V 13

DESCRIPTION Light point wired through a 5 Amp one gang one way plate switch using 2x1/1.13 ( 2x1/044)P.V.C. insulated copper wire in half surface with plastic casing and capping and other half in open air. Light points wired through a 5 Amp two gang one way using 2x1/1.13 ( 2x1/044)P.V.C. insulated copper wire in half surface with plastic casing & capping and other half in conduit. Light points wired through a 5 Amp three gang one way using 2x1/1.13 ( 2x1/044)P.V.C. insulated copper wire in half surface with plastic casing & capping and other half in conduit. Light points wired through a 5 Amp four gang one way plate switch using 2x1/1.13 ( 2x1/044)P.V.C. insulated copper wire in half surface with plastic casing & capping and other half in conduit. Light points wired through a 5 Amp. five gang one way plate switch using 2x1/1.13 ( 2x1/044)P.V.C. insulated copper wire in half surface with plastic casing & capping and other half in conduit. Light point wired through a 5Amp one gang two way plate switch using 2x1/1.13 ( 2x1/044)P.V.C. insulated copper wire in half surface with plastic casing & capping and other half in conduit.

UNIT Per Point

RATE 1670.00

V 14

Per Point

2210.00

V 15

Per Point

2835.00

V 16

Per Point

3450.00

V 17

Per Point

4075.00

V 18

Per Point

2750.00

V 19

Electric Bell with Bell press switch using 2x1/1.13mm (2x1.044 PVC/insulated copper wire in fully concealed/ surface PVC conduits. Electric Bell with bell press switch using flexible wire (twisted twin wire) only in the table legs and floor crossings. 5 Amp Switch socket outlet wired using 2x1/1.13 P.V.C. insulated copper wire & 1x7/0.67(7/029)copper earth wire in fully concealed/surface P.V.C. conduits. 5 Amp Switch socket outlet wired using 2x1/1.13 P.V.C. insulated copper wire & 1x7/0.67(7/029)copper earth wire in fully surface plastic casing and capping. 15 Amp switch socket outlet wired using 2x7/0.67(2x7/029) insulated copper wire & 1x7/0.67 copper earth wire in surface plastic casing and capping. 15 Amp switch socket outlet wired using 2x7/0.67(2x7/029) insulated copper wire & 1x7/0.67 copper earth wire in fully concealed/surface P.V.C. conduits.

Per Point

2065.00

V 20 V 21

No. No.

2155.00 1900.00

V 22

No.

2425.00

V 23

No.

2400.00

V 24

No.

2800.00

Engineering organization, W.P.

Page 50

BSR 2010

ITEM V 25

DESCRIPTION Flush mounted 13 Amp. non-reversible type square pin switched socket outlets wired in ring circuit using 4x1x7/0.67 PVC insulated copper wire and 2x7/0.67 PVC insulated copper earth wire in casing and capping. R = 600/= x L+320/= x N N

UNIT No.

RATE

R = Rate per circuit (to be calculated as per formula.
L = Distance from DB to last socket ( in Meter) N = Number of 13 Amp. sockets V 26 Fan regulator wired without a switch using 2x1/1.13 mm P.V.C. insulated copper wire 1x7/0.67 P.V.C. insulated copper earth wire in fully concealed/surface P.V.C. conduits. Fan regulator wired through a 5 Amp plate one gang one way switch using 2x1/1.13 mm P.V.C. insulated copper wire 1x7/0.67 P.V.C. insulated copper earth wire in fully concealed/surface P.V.C.conduits. Fan regulator wired without a switch using 2x1/1.13 mm P.V.C. insulated copper wire 1x7/0.67 P.V.C. insulated copper earth wire in fully surface plastic casing and capping. Fan regulator wired through a 5 Amp plate one gang one way switch using 2x1/1.13 mm P.V.C. insulated copper wire 1x7/0.67 P.V.C. insulated copper earth wire in fully surface plastic casing and capping Fan regulator wired without a switch using 2x1/1.13 mm P.V.C. insulated copper wire 1x7/0.67 P.V.C. insulated copper earth wire in half surface with plastic casing and copping and other half in open area. Fan regulator wired through a 5 Amp plate one gang one way switch using 2x1/1.13 mm P.V.C. insulated copper wire 1x7/0.67 P.V.C. insulated copper earth wire Two Fan regulator wired through a 5Amp plate two gang one way switch using 2x1/1.13 mm P.V.C. insulated copper wire 1x7/0.67 P.V.C. insulated copper earth wire in fully concealed/ surface PVC conduit Three Fan regulator wired through a 5Amp plate three gang one way switch using 2x1/1.13 mm P.V.C. insulated copper wire 1x7/0.67 P.V.C. insulated copper earth wire in fully concealed/ surface PVC conduit No. 1800.00

V 27

No.

1900.00

V 28

No.

2230.00

V 29

No.

2390.00

V 30

No.

2545.00

V 31

No.

2165.00

V 32

No.

3955.00

V 33

No.

5470.00

Engineering organization, W.P.

Page 51

BSR 2010

ITEM

DESCRIPTION Supply install and wiring the following (Rate includes wiring from MCB through switch and regulator to the fan point and includes the cost of fan)

UNIT

RATE

V 34

Supply and install a electrical fan and fan regulator wired through a 5Amp plate one gang one way switch using 2x1/1.13 mm P.V.C. insulated copper wire 1x7/0.67 P.V.C. insulated copper earth wire in fully concealed surface P.V.C. conduit. Supply and install a electrical fan and fan regulator wired through a 5Amp plate one gang one way switch using 2x1/1.13 mm P.V.C. insulated copper wire 1x7/0.67 P.V.C. insulated copper earth wire in fully concealed surface casing and capping. Supply and install a electrical fan and fan regulator wired through a 5Amp plate one gang one way switch using 2x1/1.13 mm P.V.C. insulated copper wire 1x7/0.67 P.V.C. insulated copper earth wire in fully surface with plastic casing and capping and other half in conduit. Supply & Install only the following fillings.

No.

7830.00

V 35

No.

8270.00

V 36

No.

8000.00

V 37

7" Diameter recess mounted anodized down lighter with aluminum reflector "Orange" Brand & Model No:YLI401 or approved equivalent. 7" Diameter surface mounted black colour anodized down lighter with aluminum reflector "Orange" Brand & Model No:YLI3400 or approved equivalent. 6" Diameter pendent type anodized cylindrical down lighter "Orange" Brand & Model No:FAR01 or approved equivalent. 5" / 6" Diameter wall mounted shaped upward light fitting "Orange" Brand & Model No:YLIUDL7004 or approved equivalent. Weatherproof IP64 rated aluminum die-casting surface mounted round half covered outdoor bulk head lamp "Orange" Brand & Model No:FWP43118 or approved equivalent. 8" Half round glass globe pendent type fitting "Orange" Brand & Model No:YLI401 YLIHLFGLOBE GALSS or approved equivalent. 8" White colour trasparent glass globe pendent type fitting "Orange" Brand & Model No:YLIGLOBE GALSS or approved equivalent. Bracket lamp with batton holder including bulbs Pendent Lamp 20W CFL lamp with one year warranty - Osram , Philips or Approved Equivelant. Spot light (equivalent to Osram Halospot) - German make

No.

1520.00

V 38

No.

1630.00

V 39

No.

2165.00

V 40

No.

4150.00

V 41

No.

2850.00

V 42

No.

3310.00

V 43

No. No. No. No. No.

2165.00 465.00 455.00 550.00 2275.00

V 44 V 45 V 46 V 47

Engineering organization, W.P.

Page 52

BSR 2010

ITEM V 48 V 49 V 50 V 51 V 52 V 53

DESCRIPTION Mercury Vapour Lamp bracket complete 125 watts with clamps (equivalent to Siemens SNA 395) -Ditto- 250 watts (equivalent to Siemens SNA 395) Ceiling fan 56" Sweep (KDK,National,Mitsubishi,Hittachi ) Dimmer type fan regulator with a switch (Clipsal, KDK or equivalent) Exhaust or blower fan 12" dia. (K.D.K. or Equivalent ) Wall mounted fan - European make (K.D.K. or Equivalent )

UNIT No.

RATE 7690.00

No. No. No.

14420.00 6800.00 650.00

No. No.

10850.00 12400.00

Note:
In all fluorescent lamp complete fittings incorporating, chokeAtco, BG and starter, Bulb-Philips, Osram, Thorn ChokeAtco, Starter - BG and Bulbs - Philips, osram, Thorn V 54 V 55 V 56 V 57 V 58 V 59 V 60 V 61 V 62 V 63 V 64 V 65 V 66 4-0" long x 40W single fluorescent lamp suspension - Reflector type. 4-0" long x 40W single fluorescent lamp suspension - Box type 4-0" long x 40W single fluorescent lamp suspension - Diffuser type 4' -0" long x 40W Twin fluorescent lamp suspension , powder coated - reflector type. 4' -0" long x 40W Twin fluorescent lamp suspension , powder coated - Box type 4' -0" long x 40W Twin fluorescent lamp suspension , powder coated - Diffuser type 2 x 20W single fluorescent lamp suspension , powder coated reflector type 2 x 20W single fluorescent lamp suspension , powder coated Box type 2 x 20W single fluorescent lamp suspension , powder coated Diffuser type 2'-0" long x 20W Twin fluorescent lamp suspension , powder coated - Reflector type 2'-0" long x 20W Twin fluorescent lamp suspension , powder coated - Box type 2'-0" long x 20W Twin fluorescent lamp suspension , powder coated - Diffuser type 4'-0" long x 20W single fluorescent lamp Batten , powder coated Reflector type No. No. No. No. No. No. No. No. No. No. No. No. No. 1000.00 1000.00 1150.00 1500.00 1500.00 2050.00 760.00 830.00 995.00 1300.00 1300.00 1550.00 850.00

Engineering organization, W.P.

Page 53

BSR 2010

ITEM V 67 V 68 V 69 V 70 V 71 V 72 V 73 V 74 V 75 V 76 V 77 V 78

DESCRIPTION 4'-0" long x 20W single fluorescent lamp Batten , powder coated Box type 4'-0" long x 20W single fluorescent lamp Batten , powder coated Diffuser type 4'-0" long x 20W Twin Fluorescent lamp Batten , powder coated Reflector type 4'-0" long x 20W Twin Fluorescent lamp Batten , powder coated Box type 4'-0" long x 20W Twin Fluorescent lamp Batten , powder coated Diffuser type 2'-0" x 40W single fluorescent lamp Batten , powder coated Reflector type 2'-0" x 40W single fluorescent lamp Batten , powder coated Box type 2'-0" x 40W single fluorescent lamp Batten , powder coated Diffuser type 2'-0" long x 40W Twin fluorescent lamp Batten , powder coated Reflector type 2'-0" long x 40W Twin fluorescent lamp Batten , powder coated Box type 2'-0" long x 40W Twin fluorescent lamp Batten , powder coated Diffuser type 4-8 ways SP&N Distribution Board with thermo plastic frame and door, earth and neutral bars din trail type (protection rating IP40) 8-10 ways SP&N Distribution board with thermo plastic frame and door, earth and neutral bars din trail type (protection rating IP40) 10-12 ways SP&N Distribution board with thermo plastic frame and door, earth and neutral bars din trail type (protection rating IP40) 14-16 ways SP&N distribution board with thermo plastic frame and door, earth and neutral bars din trail type (protection rating IP40) 16-19 ways SP&N Distribution board with thermo plastic frame and door, earth and neutral bars din trail type (protection rating IP40) Provide an earth electrode copper plate 2'-0"x2'-0"x1/8" in 3m deep. Rate to include connection to the main panel, sub main, earth clips, excavation etc. with 1'-0"x 1'-0"x 1'-0" earth pit including 4 1/2" brick work and 3" concrete slab.

UNIT No. No. No. No. No. No. No. No. No. No. No. No.

RATE 850.00 1230.00 1300.00 1300.00 1515.00 1175.00 1175.00 1690.00 1380.00 1380.00 1590.00 1420.00

V 79

No.

1420.00

V 80

No.

1610.00

V 81

No.

1825.00

V 82

No.

1825.00

V 83

Item

20000.00

Engineering organization, W.P.

Page 54

BSR 2010

ITEM V 84

DESCRIPTION Provide an earth electrode 2" dia 6'0" long G.I. pipe -ditto- with 1'-0"x 1'-0"x 1'-0" earth pit including 4 1/2" brick work and 3" concrete slab. Supplying and wiring 2 x 2.5mm2 (7/.029") PVC/PVC/Cu cable + 2.5mm2 (7/.029) earth wire to working order excluding conduit. Supplying and wiring 2 x 6mm2 (7/.044") PVC/PVC/ Cu cable + 6mm2 (7/.044") earth wire complete to working order excluding conduit/casing Supplying and wiring 2 x 6mm2 (7/.044") PVC/PVC/ Cu cable complete to working order excluding conduit/casing Supplying and wiring 4 x 6mm2 (7/.044") PVC/PVC/ Cu cable + 6mm2 (7/.044") earth wire complete to working order excluding conduit/casing Supplying and wiring 2 x 10mm2 (7/.052") PVC/PVC/ Cu cable + 10mm2 (7/.052") earth wire complete to working order excluding conduit/casing Supplying and wiring 4 x 10mm2 (7/.052") PVC/PVC/ Cu cable + 10mm2 (7/.052") earth wire complete to working order excluding conduit/casing Supplying and wiring 2 x 16mm (7/.064") PVC/PVC/ Cu cable + 16mm2 (7/.064") earth wire complete to working order excluding conduit/casing Supplying and wiring 4 x 16mm (7/0.064") PVC/PVC/ Cu cable + 16mm2 (7/.064") earth wire complete to working order excluding conduit/casing Supplying and wiring 2 x 25mm2 PVC/PVC/Cu cable + 16 mm2 earth wire complete to working order excluding conduit/casing. Supplying and wiring 4 x 25mm2 PVC/PVC/Cu cable + 16 mm2 earth wire complete to working order excluding conduit/casing.
2 2 2 2

UNIT Item

RATE 1470.00

V 85

L.ft.

50.00

V 86

L.ft.

118.00

V 87 V 88

L.ft. L.ft.

91.00 183.00

V 89

L.ft.

167.00

V 90

L.ft.

281.00

V 91

L.ft.

254.00

V 92

L.ft.

429.00

V 93

L.ft.

421.00

V 94

L.ft.

707.00

V 95

Supplying and wiring 4 x 35mm PVC/PVC/Cu cable + 16 mm earth wire complete to working order excluding conduit/casing.

L.ft.

863.00

V 96

Supplying and wiring 4 x 95mm2 PVC/PVC/Cu cable + 50 mm2 earth wire complete to working order excluding conduit/casing. Supplying and fixing 2 core flexible (0.5mm2) . Supplying and wiring 2.5mm2 (7/.029") earth wire complete to working order excluding conduit/casing. Supplying and wiring 6 mm (7/.044") earth wire complete to working order excluding conduit/casing.
2

L.ft.

2450.00

V 97 V 98 V 99

L.ft. L.ft. L.ft.

14.00 13.00 51.00

Engineering organization, W.P.

Page 55

BSR 2010

ITEM

DESCRIPTION

UNIT L.ft. L.ft. L.ft. L.ft. L.ft. L.ft.

RATE 60.00 88.00 11.00 27.00 34.00 80.00

V 100 Supplying and wiring 10 mm2 (7/.052") earth wire complete to working order excluding conduit/casing. V 101 Supplying and wiring 16 mm2 (7/.064") earth wire complete to working order excluding conduit/casing. V 102 Supplying and wiring 1mm2 (1/.044") PVC/PVC/ Cu two wire complete to working order excluding conduit/casing. V 103 Supplying and wiring 2.5mm2 ((7/.029") PVC/PVC Cu two wire complete to working order excluding conduit/casing. V 104 Supplying and wiring with 4mm2 (7/.036") PVC/PVC/Cu two wire complete to working order excluding conduit/casing. V 105 Supplying and wiring with 2 x 4mm2 (7/.036") PVC/PVC/Cu cable+4mm2(7/.036) earth wire complete to working order excluding conduit/casing. V 106 Supplying and wiring with 4 x 4mm2 (7/.036") PVC/PVC/Cu cable+4mm2(7/.036) earth wire complete to working order excluding conduit/casing. V 107 Supplying and wiring with 2 x 2.5mm2(7/.029") PVC/PVC/Cu cable+2.5mm2(7/.036) earth wire complete to working order excluding conduit/casing. V 108 Supply and wiring 2 x 6mm2(7/044) PVC/PVC/CU Cable complete to working order excluding conduit & casing Note: Supply, install and wire with enclosure the following makes : Cabtree, F & G, Genuine, Merlin & Gerin, Terrasaki,. V 109 40Amp(30 mA) SP&N RCCB V 110 40Amp(100 mA) SP&N RCCB V 111 60Amp(30 mA) SP&N RCCB V 112 60Amp(100 mA) SP&N RCCB V 113 40Amp(30 mA) TP&N RCCB V 114 40Amp(100 mA) TP&N RCCB V 115 60Amp(30 mA) TP&N RCCB V 116 60Amp(100 mA) TP&N RCCB V 117 Main switch 30 Amp SP&N V 118 MCB SP (Single Pole) 6-40 Amp

L.ft.

135.00

L.ft.

55.00

L.ft.

100.00

No. No. No. No. No. No. No. No. No. No.

3215.00 3475.00 4675.00 5800.00 4590.00 4590.00 7945.00 7955.00 1245.00 737.00

Engineering organization, W.P.

Page 56

BSR 2010

ITEM V 119 MCB SP 50-100 Amp

DESCRIPTION

UNIT No. No. No. No. No. No. No.

RATE 3530.00 1730.00 1775.00 3680.00 4885.00 12000.00 16250.00

V 120 MCB DP (Double Pole) 6-40 Amp V 121 MCB DP 50-100 Amp V 122 MCB TP ( Three Pole) 6-40 Amp V 123 MCB TP 50-100 Amp V 124 30,40,60,100 Amp Three pole MCCB with metal enclosure 30,40,60,100 Amp four pole MCCB (25KA) with metal V 125 enclosure V 126 30,40,60,100Amp Three pole MCCB without enclosure V 127 30,40,60,100Amp Three pole MCCB (25 Ka) without enclosure

No. No. No. No. No. No. No. No. No.

9600.00 13900.00 4950.00 8840.00 127.00 2255.00 3050.00 5130.00 1680.00 25.00

V 128 30 Amp TP&N main switch V 129 60 Amp TP&N main switch V 130 D'Bracket complete set (small size) Supplying and fixing 30 A T.P.N. isolator complete to working V 131 order with enclosure. Supplying and fixing 60 A T.P.N. isolator complete to working V 132 order with enclosure. Supplying and fixing 100 A T.P.N. isolator complete to working V 133 order with enclosure. Supplying and fixing 100 A T.P.N. isolator complete to working V 134 order with enclosure. 3/4" - 1" PVC conduits laying in the slab including placing V 135 binding wire to draw through conduits. V 136 Supplying and fixing 5/8" PVC conduit including clips. V 137 Supplying and fixing 3/4" PVC conduit including clips. V 138 Supplying and fixing 1" PVC conduit including clips. V 139 Supplying and fixing 3" dia. PVC type 400 pipe including clips. Supplying and fixing 1 1 /2" dia. PVC type 400 pipe including V 140 clips. Supplying and fixing 1 1 /4" dia. PVC type 400 pipe including V 141 clips. V 142 Supplying and fixing 3/4" dia. PVC conduit bend V 143 Supplying and fixing 1" dia. PVC conduit bend

L.ft. L.ft. L.ft. L.ft. L.ft. L.ft. L.ft. 16.00 17.00 18.00 210.00 55.00 50.00

No. No.

22.00 26.00

Engineering organization, W.P.

Page 57

BSR 2010

ITEM

DESCRIPTION

UNIT No. No. No. L.ft. L.ft. L.ft. L.ft. No. L.ft. L.ft. L.ft. L.ft. L.ft. Per Set L.ft.

RATE 65.00 45.00 95.00 41.00 58.00 66.00 15.00 24.00 20.00 24.00 28.00 38.00 65.00 214.00 220.00

V 144 Supplying and fixing 1 1/2" dia. PVC conduit bend V 145 Supplying and fixing 1 1/4" dia. PVC conduit bend V 146 Supplying and fixing 2" dia. PVC conduit bend V 147 Supplying and fixing 1 1/4" dia. PVC conduit pipe V 148 Supplying and fixing 1 1/2" dia. PVC conduit pipe V 149 Supplying and fixing 2" dia. PVC conduit pipe V 150 Supplying and fixing 1" dia. PVC conduit pipe V 151 Supplying and fixing 3/4" or 1" PVC conduit junction box. V 152 Supplying and fixing 1" PVC casing V 153 Supplying and fixing 1 1/4" PVC casing V 154 Supplying and fixing 1 1/2" PVC casing V 155 Supplying and fixing 2" PVC casing V 156 Supplying and fixing 2"x 2: box casing. PVC casing V 157

Supply and install complete "D" shape bracket including insulator, Nuts, bolts ect. fixed to working order.

Supply and install 2" x 2" x 6mm "L" Iron, including drilling V 158 12mm holes, 10mm G.I. bolt, and application of anticorrosive paint all complete to working order.
Supply and install Recessed type ceiling lights with louvered V 159 mirror type, florescent lamp fitting with (a) 2'-0" x 1'0"- 2 no 20 watts fluorescent lamps (b) 2'-0" x 2'0"- 4 no 20 watts fluorescent lamps (c) 2'-0" x 1'0"- 4 no 20 watts fluorescent lamps (d) 4'-0" x 1'0"- 2 no 40 watts fluorescent lamps (e) 4'-0" x 1'0"- 3 no 40 watts fluorescent lamps (f) 4'-0" x 4'0"- 4 no 40 watts fluorescent lamps V 160 Supply and installation and connection of 25 x 3mm copper tape with necessary accessories. Rate shall include for connection of both ends with brass. V 161 Supply and installation and connection of 30A - 60A three phase with powder coated locable bus bar box including neutral bar and earth bar.

No. No. No. No. No. No. L.ft.

2880.00 3410.00 4530.00 3580.00 5340.00 5985.00 475.00

No.

6340.00

Engineering organization, W.P.

Page 58

BSR 2010

ITEM

DESCRIPTION

UNIT No.

RATE 9225.00

V 162 Supply and installation and connection of 100A - 125A three phase with powder coated locable bus bar box including neutral bar and earth bar. V 163 Supply and installation and connection of 30A - 60A single phase with powder coated locable bus bar box including neutral bar and earth bar. V 164 Testing of the electrical installation and submission of certificate from a chartered Electrical Engineer registerd at CEB.

No.

4630.00

Item

9000.00

W - METAL WORK
Note: Aluminium doors, windows and partitions shall confirm to the following requirements: 1 2 3 Aluminium alloy should confirm to- BS 1474:1972 Surface treatment shall confirm to BS 1615 and BS 3987 Anodized coating thickness should be 15 +/- 5 microns Minimum section thickness 1.6mm door frame , 1.5 mm window frame and 1.2 mm partition. Most of the aluminium extrusions available in the Local Market are being manufactured in Sri Lanka by the following leading companies and both companies are changing the extrusion profiles and thicknesses from time to time. Hence it has become very difficult t o specify standard section sizes that are to be used for door /window frames and sash members. Hence the rates given herein are based on the recommended minimum sizes and thicknesses and profiles as per their hand books published by M/S ALUMAX (PVT) LTD and by M/S LANKA ALUMINIUM INDUSTRIES LTD and M/S HEMALCO LTD. At the time of bidding, all the Bidders shall specifically be requested to submit the following information. The specifications and thickness of Aluminium extrusions bidder proposes to use on the works. Full size cross sections Documentary evidence from the Profile Manufacture to the effect that the proposed profile will serve for the intended purpose. A Manufacturer's test certificate be produced as evidence that the powder coating is of required thickness.

4

5

(a) (b)

(c)

(d)

Engineering organization, W.P.

Page 59

BSR 2010

ITEM 6 Physical properties :-

DESCRIPTION

UNIT

RATE

(a) Minimum tensile strength 150 Mpa (b) Elongation 7% 7 8 All screws should be stainless steel But hinges and bar type hinges should be Aluminium or Stainless Steel. The item descriptions should be read along with the annexed detail drawings. Drawing no:- AR/TYPE PLAN/DOORS & WINDOWS/2010.07.07/DETAIL 1 - 18 ( Sheet 1 - 18 ) 100Door-1.6mm thick, 70 Casement-1.5 mmthick, 80 Sliding-1.5mm thick, 76 Partition 1.2mm thick Shop drawing should be provided prior to fabrication. The rates and hence the item description shall include 5mm thick Tinted glass, Neoprene gasket, pop revets, Rawl plugs, Screws, Aluminium cleats etc. The rates given herein are for Natural aluminium profiles. For powder coated aluminium profiles (minimum powder coating thickness of 40 + 5 microns) the rates shall be increased by 15%. For Bronze anodized aluminium profiles, the rates shall be increased by 5%. Doors W 01 Openable Single Sash Door (Aluminium Composite Panel & Glazed ) with Louvers on Top Natural aluminium single sash butt hinged openable door with middle rail and louvers on top , panelling with two layers of 4mm thick aluminium composite panel on both side and glazed with 5mm thick tinted glass panes, neoprene and woold beading, gaskets, pop rivots, threaded bar with nut and approved quality lock, butt hinges, door handle with cap nut. As per the members , sizes and details given in Drawing No:- AR/TYPE PLAN/DOORS & WINDOWS/2010.07.07/ DETAIL 02 - D1 Sq.ft. 1,315.00

9

10

11

12

13

Engineering organization, W.P.

Page 60

BSR 2010

ITEM W 02

DESCRIPTION Openable Single Sash Door (Aluminium Composite Panel & Glazed ) with Fixed Glass on Top Natural aluminium single sash butt hinged openable door with middle rail and fixed glass on top , panelling with two layers of 4mm thick aluminium composite panel on both side and glazed with 5mm thick tinted glass panes, neoprene and woold beading, gaskets, pop rivots, threaded bar with nut and approved quality lock, butt hinges, door handle with cap nut. As per the members , sizes and details given in Drawing No:- AR/TYPE PLAN/DOORS & WINDOWS/2010.07.07/ DETAIL 02 - D2

UNIT

RATE

Sq.ft.

1,230.00

W 03

Openable Single Sash Door (Aluminium Composite Panel & Glazed ) Natural aluminium single sash butt hinged openable door with middle rail , panelling with two layers of 4mm thick aluminium composite panel on both side and glazed with 5mm thick tinted glass panes, neoprene and woold beading, gaskets, pop rivots, threaded bar with nut and approved quality lock, butt hinges, door handle with cap nut. As per the members , sizes and details given in Drawing No:AR/TYPE PLAN/DOORS & WINDOWS/2010.07.07/ DETAIL 02 - D3 Openable Single Sash Door (Fully Glazed ) with Louvers on Top Natural aluminium single sash butt hinged openable door with middle rail and louvers on top , glazed with 5mm thick tinted glass panes, neoprene and woold beading, gaskets, pop rivots, threaded bar with nut and approved quality lock, butt hinges, door handle with cap nut. As per the members , sizes and details given in Drawing No:AR/TYPE PLAN/DOORS & WINDOWS/2010.07.07/ DETAIL 03 - D4

Sq.ft.

1,330.00

W 04

Sq.ft.

930.00

W 05

Openable Single Sash Door (Fully Glazed ) with Fixed Glass on Top Natural aluminium single sash butt hinged openable door with middle rail and fixed glass on top , glazed with 5mm thick tinted glass panes, neoprene and woold beading, gaskets, pop rivots, threaded bar with nut and approved quality lock, butt hinges, door handle with cap nut. As per the members , sizes and details given in Drawing No:AR/TYPE PLAN/DOORS & WINDOWS/2010.07.07/ DETAIL 03 - D5

Sq.ft.

845.00

W 06

Openable Single Sash Door ( Fully Glazed )

Engineering organization, W.P.

Page 61

BSR 2010

ITEM

DESCRIPTION Natural aluminium single sash butt hinged openable door with middle rail and glazed with 5mm thick tinted glass panes, neoprene and woold beading, gaskets, pop rivots, threaded bar with nut and approved quality lock, butt hinges, door handle with cap nut. As per the members , sizes and details given in Drawing No:- AR/TYPE PLAN/DOORS & WINDOWS/ 2010.07.07/ DETAIL 03 - D6 Openable Single Sash Door ( Fully panelled with Aluminium Composite Panel ) Natural aluminium single sash butt hinged openable door with middle rail and fully panelling with two layers of 4mm thick aluminium composite panel on both side, neoprene and woold beading, gaskets, pop rivots, threaded bar with nut and approved quality lock, butt hinges, door handle with cap nut. As per the members , sizes and details given in Drawing No:- AR/TYPE PLAN/DOORS & WINDOWS/ 2010.07.07/ DETAIL 04 - D7 & D8 Sliding Single Sash Door (Aluminium Composite Panel & Glazed ) Natural aluminium single sash sliding door with middle rail , panelling with two layers of 4mm thick aluminium composite panel on both side and glazed with 5mm thick tinted glass panes, neoprene and woold beading, gaskets, pop rivots, threaded bar with nut roller, flush bolt and approved quality lock , door handle with cap nut. As per the members , sizes and details given in Drawing No:- AR/TYPE PLAN/DOORS & WINDOWS/ 2010.07.07/ DETAIL 05 - D9

UNIT Sq.ft.

RATE 860.00

W 07

Sq.ft.

1,795.00

W 08

Sq.ft.

1,160.00

W 09

Sliding Single Sash Door ( Fully Glazed ) Natural aluminium single sash fully glazed sliding door with middle rail , glazed with 5mm thick tinted glass panes, neoprene and woold beading, gaskets, pop rivots, threaded bar with nut roller, flush bolt and approved quality lock , door handle with cap nut. As per the members , sizes and details given in Drawing No:AR/TYPE PLAN/DOORS & WINDOWS/ 2010.07.07/ DETAIL 05 - D10 Sq.ft. 620.00

W 10

Sliding Single Sash Door ( Fully panelled with Aluminium Composite Panel ) Natural aluminium single sash sliding door with middle rail , fully panelling with two layers of 4mm thick aluminium composite panel on both side, neoprene and woold beading, gaskets, pop rivots, threaded bar with nut roller, flush bolt and approved quality lock , door handle with cap nut. As per the members , sizes and details given in Drawing No:- AR/TYPE PLAN/DOORS & WINDOWS/ 2010.07.07/ DETAIL 05 - D11 Sq.ft. 1,695.00

Engineering organization, W.P.

Page 62

BSR 2010

ITEM

DESCRIPTION

UNIT

RATE

W 11

Openable Double Sash Door (Aluminium Composite Panel & Glazed ) with Fixed Glass on Top Natural aluminium double sash butt hinged openable door with middle rail and fixed glass on top , panelling with two layers of 4mm thick aluminium composite panel on both side and glazed with 5mm thick tinted glass panes, neoprene and woold beading, gaskets, pop rivots, threaded bar with nut and approved quality lock, butt hinges, door handle with cap nut. As per the members , sizes and details given in Drawing No:- AR/TYPE PLAN/DOORS & WINDOWS/2010.07.07/ DETAIL 06 - D12 Sq.ft. 1,295.00

W 12

Openable Double Sash Door (Aluminium Composite Panel & Glazed ) with Louvers on Top Natural aluminium double sash butt hinged openable door with middle rail and louvers on top , panelling with two layers of 4mm thick aluminium composite panel on both side and glazed with 5mm thick tinted glass panes, neoprene and woold beading, gaskets, pop rivots, threaded bar with nut and approved quality lock, butt hinges, door handle with cap nut. As per the members , sizes and details given in Drawing No:- AR/TYPE PLAN/DOORS & WINDOWS/2010.07.07/ DETAIL 06 - D13 Sq.ft. 1,320.00

W 13

Openable Double Sash Door (Aluminium Composite Panel & Glazed ) Natural aluminium double sash butt hinged openable door with middle rail , panelling with two layers of 4mm thick aluminium composite panel on both side and glazed with 5mm thick tinted glass panes, neoprene and woold beading, gaskets, pop rivots, threaded bar with nut and approved quality lock, butt hinges, door handle with cap nut. As per the members , sizes and details given in Drawing No:AR/TYPE PLAN/DOORS & WINDOWS/2010.07.07/ DETAIL 06 - D14 Sq.ft. 1,390.00

W 14

Openable Double Sash Door (Fully Glazed ) with Fixed Glass on Top Natural aluminium double sash butt hinged openable door with middle rail and fixed glass on top , fully glazed with 5mm thick tinted glass panes, neoprene and woold beading, gaskets, pop rivots, threaded bar with nut and approved quality lock, butt hinges, door handle with cap nut. As per the members , sizes and details given in Drawing No:- AR/TYPE PLAN/DOORS & WINDOWS/2010.07.07/ DETAIL 07 - D15 Sq.ft. 840.00

Engineering organization, W.P.

Page 63

BSR 2010

ITEM W 15

DESCRIPTION Openable Double Sash Door (Fully Glazed ) with Louvers on Top Natural aluminium double sash butt hinged openable door with middle rail and louvers on top , fully glazed with 5mm thick tinted glass panes, neoprene and woold beading, gaskets, pop rivots, threaded bar with nut and approved quality lock, butt hinges, door handle with cap nut. As per the members , sizes and details given in Drawing No:AR/TYPE PLAN/DOORS & WINDOWS/2010.07.07/DETAIL 07 - D16

UNIT

RATE

Sq.ft.

905.00

W 16

Openable double Sash Door ( Fully Glazed ) Natural aluminium double sash butt hinged openable door with middle rail and fully glazed with 5mm thick tinted glass panes, neoprene and woold beading, gaskets, pop rivots, threaded bar with nut and approved quality lock, butt hinges, door handle with cap nut. As per the members , sizes and details given in Drawing No:AR/TYPE PLAN/DOORS & WINDOWS/ 2010.07.07/DETAIL 07 - D17 Sliding Double Sash Door (Aluminium Composite Panel & Glazed ) Natural aluminium double sash sliding door with middle rail , panelling with two layers of 4mm thick aluminium composite panel on both side and glazed with 5mm thick tinted glass panes, neoprene and woold beading, gaskets, pop rivots, threaded bar with nut roller, flush bolt and approved quality lock , door handle with cap nut. As per the members , sizes and details given in Drawing No:- AR/TYPE PLAN/DOORS & WINDOWS/ 2010.07.07/DETAIL 08 - D18 Sq.ft. 1150.00 Sq.ft. 885.00

W 17

W 18

Sliding Double Sash Door ( Fully Glazed ) with Fixed Glass on Top Natural aluminium double sash fully glazed sliding door with middle rail , fully glazed with 5mm thick tinted glass panes, neoprene and woold beading, gaskets, pop rivots, threaded bar with nut roller, flush bolt and approved quality lock , door handle with cap nut. As per the members , sizes and details given in Drawing No:- AR/TYPE PLAN/DOORS & WINDOWS/ 2010.07.07/DETAIL 08 - D19 Sq.ft. 590.00

Engineering organization, W.P.

Page 64

BSR 2010

ITEM W 19

DESCRIPTION Openable Single Sash Door for Toilets ( with Aluminium Sheet ) Natural aluminium single sash butt hinged openable door with middle rail and gauge 24 aluminium sheet, neoprene and woold beading, gaskets, pop rivots, threaded bar with nut and approved quality lock, butt hinges, door handle with cap nut. As per the members , sizes and details given in Drawing No:- AR/TYPE PLAN/DOORS & WINDOWS/2010.07.07/ DETAIL 04 - D20

UNIT

RATE

Sq.ft.

650.00

Windows W 20 Casement Window with Louvers on Top ( 1 Bay ) Natural aluminium casement window single sash with louvers on top, consisting of 5mm thick glass panes, casement lock, pull rings , screws, pop rivots, gaskets, door hinge, weather strip etc.As per the members , sizes and details given in Drawing No:AR/TYPE PLAN/DOORS & WINDOWS/ 2010.07.07/DETAIL 09 - W1 Sq.ft. 1120.00

W 21

Casement Window with Fixed Glass on Top ( 1 Bay ) Natural aluminium casement window single sash with fixed glass on top, consisting of 5mm thick glass panes, casement lock, screws, pop rivots, gaskets, door hinge, weather strip etc.As per the members , sizes and details given in Drawing No:- AR/TYPE PLAN/DOORS & WINDOWS/ 2010.07.07/ DETAIL 09 - W2 Sq.ft. 1055.00

W 22

Casement Window ( 1 Bay ) Natural aluminium casement window single sash , consisting of 5mm thick glass panes, casement lock, screws, pop rivots, gaskets, door hinge, weather strip etc.As per the members , sizes and details given in Drawing No:- AR/TYPE PLAN/ DOORS & WINDOWS/2010.07.07/DETAIL 09 - W3 Sq.ft. 1,025.00

W 23

Casement Window with Louvers on Top ( 2 Bays ) Natural aluminium casement window double sash with louvers on top, consisting of 5mm thick glass panes, casement lock, screws, pop rivots, gaskets, door hinge, weather strip etc.As per the members , sizes and details given in Drawing No:- AR/TYPE PLAN/ DOORS & WINDOWS/2010.07.07/ DETAIL 10 - W4 Sq.ft. 990.00

Engineering organization, W.P.

Page 65

BSR 2010

ITEM W 24

DESCRIPTION Casement Window with Fixed Glass on Top ( 2 Bays ) Natural aluminium casement window double sash with fixed glass on top, consisting of 5mm thick glass panes, casement lock, screws, pop rivots, gaskets, door hinge, weather strip etc.As per the members , sizes and details given in Drawing No:- AR/TYPE PLAN/ DOORS & WINDOWS/2010.07.07/ DETAIL 10 - W5

UNIT

RATE

Sq.ft.

910.00

W 25

Casement Window ( 2 Bays ) Natural aluminium casement window double sash , consisting of 5mm thick glass panes, casement lock, screws, pop rivots, gaskets, door hinge, weather strip etc. As per the members , sizes and details given in Drawing No:- AR/TYPE PLAN/ DOORS & WINDOWS/2010.07.07/ DETAIL 10 - W6 Sq.ft. 890.00

W 26

Sliding Window with Louvers on Top ( 2 Bays ) Natural aluminium sliding window with louvers on top consisting of 5mm thick glass panes , lock, roller, screws, gaskets, nut felt, pop rivots, cap, plastic guide etc. As per the members , sizes and details given in Drawing No:- AR/TYPE PLAN/DOORS & WINDOWS/ 2010.07.07/ DETAIL 11 - W7 Sq.ft. 905.00

W 27

Sliding Window with Fixed Glass on Top ( 2 Bays ) Natural aluminium sliding window with fixed glass on top consisting of 5mm thick glass panes , lock, roller, screws, gaskets, nut felt, pop rivots, cap, plastic guide etc. As per the members , sizes and details given in Drawing No:- AR/TYPE PLAN/DOORS & WINDOWS/ 2010.07.07/ DETAIL 11 - W8 Sq.ft. 815.00

W 28

Sliding Window ( 2 Bays ) Natural aluminium sliding window ,consisting of 5mm thick glass panes , lock, roller, screws, gaskets, nut felt, pop rivots, cap, plastic guide etc. As per the members , sizes and details given in Drawing No:- AR/ TYPE PLAN/ DOORS & WINDOWS/ 2010.07.07/ DETAIL 11 - W9 Sq.ft. 730.00

W 29

Casement Window with Louvers on Top ( 3 Bays ) Natural aluminium casement window with louvers on top, consisting of 5mm thick glass panes, casement lock, screws, pop rivots, gaskets, door hinge, weather strip etc.As per the members , sizes and details given in Drawing No:- AR/ TYPE PLAN/DOORS & WINDOWS/ 2010.07.07/ DETAIL 12 - W10 Sq.ft. 985.00

Engineering organization, W.P.

Page 66

BSR 2010

ITEM

DESCRIPTION

UNIT

RATE

W 30

Casement Window with Fixed Glass on Top ( 3 Bays ) Natural aluminium casement window with fixed glass on top, consisting of 5mm thick glass panes, casement lock, screws, pop rivots, gaskets, door hinge, weather strip etc.As per the members , sizes and details given in Drawing No:- AR/ TYPE PLAN/DOORS & WINDOWS/ 2010.07.07/ DETAIL 12 - W11 Sq.ft. 895.00

W 31

Casement Window ( 3 Bays ) Natural aluminium casement window, consisting of 5mm thick glass panes, casement lock, screws, pop rivots, gaskets, door hinge, weather strip etc. As per the members , sizes and details given in Drawing No:- AR/ TYPE PLAN/DOORS & WINDOWS/ 2010.07.07/ DETAIL 12 - W12 Sq.ft. 865.00

W 32

Sliding Window with Louvers on Top ( 3 Bays ) Natural aluminium sliding window with louvers on top consisting of 5mm thick glass panes , lock, roller, screws, gaskets, nut felt, pop rivots, cap, plastic guide etc. As per the members , sizes and details given in Drawing No:- AR/ TYPE PLAN/DOORS & WINDOWS/ 2010.07.07/ DETAIL 13 - W13 Sq.ft. 870.00

W 33

Sliding Window with Fixed Glass on Top ( 3 Bays ) Natural aluminium sliding window with fixed glass on top consisting of 5mm thick glass panes , lock, roller, screws, gaskets, nut felt, pop rivots, cap, plastic guide etc. As per the members , sizes and details given in Drawing No:- AR/ TYPE PLAN/DOORS & WINDOWS/ 2010.07.07/ DETAIL 13 - W14 Sq.ft. 840.00

W 34

Sliding Window ( 3 Bays ) Natural aluminium sliding window ,consisting of 5mm thick glass panes , lock, roller, screws, gaskets, nut felt, pop rivots, cap, plastic guide etc. As per the members , sizes and details given in Drawing No:- AR/ TYPE PLAN/DOORS & WINDOWS/ 2010.07.07/ DETAIL 13 - W15 Sq.ft. 815.00

Engineering organization, W.P.

Page 67

BSR 2010

ITEM W 35

DESCRIPTION Top Hung Casement Window with Fixed Louvers on Top & Fixed Glass at Bottom (3 Bays ) Natural aluminium top hung casement window with fixed glass on top and fixed glass at bottom, consisting of 5mm thick glass panes, casement lock, screws, pop rivots, gaskets, door hinge, weather strip etc.As per the members , sizes and details given in Drawing No:- AR/ TYPE PLAN/DOORS & WINDOWS/ 2010.07.07/ DETAIL 14 - W16

UNIT

RATE

Sq.ft.

1,030.00

W 36

Top Hung Casement Window with Fixed Louvers on Top & Fixed Glass at Bottom (2 Bays ) Natural aluminium top hung casement window with fixed glass on top and fixed glass at bottom, consisting of 5mm thick glass panes, casement lock, screws, pop rivots, gaskets, door hinge, weather strip etc.As per the members , sizes and details given in Drawing No:- AR/ TYPE PLAN/DOORS & WINDOWS/ 2010.07.07/ DETAIL 14 - W17 Sq.ft. 1,000.00

W 37

Casement Window with Louvers on Top ( 4 Bays ) Natural aluminium casement window with louvers on top, consisting of 5mm thick glass panes, casement lock, screws, pop rivots, gaskets, door hinge, weather strip etc.As per the members , sizes and details given in Drawing No:- AR/ TYPE PLAN/DOORS & WINDOWS/ 2010.07.07/ DETAIL 15 - W18 Sq.ft. 860.00

W 38

Casement Window with Fixed Glass on Top ( 4 Bays ) Natural aluminium casement window with fixed glass on top, consisting of 5mm thick glass panes, casement lock, screws, pop rivots, gaskets, door hinge, weather strip etc.As per the members , sizes and details given in Drawing No:- AR/ TYPE PLAN/DOORS & WINDOWS/ 2010.07.07/ DETAIL 15 - W19 Sq.ft. 735.00

W 39

Louver Panel 1 Natural aluminium framed lovers, consisting of screws, pop rivots, etc. As per the members , sizes and details given in Drawing No:- AR/ TYPE PLAN/DOORS & WINDOWS/ 2010.07.07/ DETAIL 16 - W20 Sq.ft. 685.00

W 40

Louver Panel 2 Natural aluminium framed lovers, consisting of screws, pop rivots, etc. As per the members , sizes and details given in Drawing No:- AR/ TYPE PLAN/DOORS & WINDOWS/ 2010.07.07/ DETAIL 16 - W21 Sq.ft. 555.00

Engineering organization, W.P.

Page 68

BSR 2010

ITEM W 41

DESCRIPTION Top Hung Fanlight with Lover panel on top Natural aluminium top hung type fanlight with louver on top consisting of locks, screws, pop rivots, gaskets, door hinge, weather strip etc. As per the members , sizes and details given in Drawing No:- AR/ TYPE PLAN/DOORS & WINDOWS/ 2010.07.07/ DETAIL 17 - FL1

UNIT

RATE

Sq.ft.

1,290.00

W 42

Top Hung Fanlight with Fixed Glass on top Natural aluminium top hung type fanlight with fixed glass on top consisting of locks, screws, pop rivots, gaskets, door hinge, weather strip etc. As per the members , sizes and details given in Drawing No:- AR/ TYPE PLAN/DOORS & WINDOWS/ 2010.07.07/ DETAIL 17 - FL2 Sq.ft. 1,165.00

W 43

Centre Pivot Fanlight with Lover panel on top Natural aluminium centre pivot type fanlight with louver on top consisting of locks, screws, pop rivots, gaskets, door hinge, weather strip etc. As per the members , sizes and details given in Drawing No:- AR/ TYPE PLAN/DOORS & WINDOWS/ 2010.07.07/ DETAIL 17 - FL3 Sq.ft. 1,370.00

W 44

Top Hung Fanlight with Fixed Glass on top Natural aluminium centre pivot type fanlight with fixed glass on top consisting of locks, screws, pop rivots, gaskets, door hinge, weather strip etc. As per the members , sizes and details given in Drawing No:- AR/ TYPE PLAN/DOORS & WINDOWS/ 2010.07.07/ DETAIL 17 - FL4 Sq.ft. 1,200.00

W 45

Top Hung Fanlight ( 3 bays ) Natural aluminium top hung type fanlight 3 bays, consisting of locks, screws, pop rivots, gaskets, door hinge, weather strip etc. As per the members , sizes and details given in Drawing No:- AR/ TYPE PLAN/DOORS & WINDOWS/ 2010.07.07/ DETAIL 18 FL5 Sq.ft. 740.00

W 46

Top Hung Fanlight ( 2 Bays + 1 Bay ) Natural aluminium top hung type fanlight 2 bays + 1 bay, consisting of locks, screws, pop rivots, gaskets, door hinge, weather strip etc. As per the members , sizes and details given in Drawing No:- AR/ TYPE PLAN/DOORS & WINDOWS/ 2010.07.07/ DETAIL 18 - FL6 Sq.ft. 755

Fixed Glazed Window W 47 Natural aluminium fixed glaxed window with 5mm thick tinted glazed and screws, pop rivots, gasket and wool felt etc. Sq.ft. 550.00

Engineering organization, W.P.

Page 69

BSR 2010

ITEM

DESCRIPTION

UNIT

RATE

Fully Board Partition with Emboss Decorative Plywood W 48 Natural aluminium partition frame top and bottom with 2.5mm thick emboss laminated plywood boarding both side kept back to back ( Total thickness 5mm ) with necessary pop rivots, gasket and GI channels & etc. work complete in order. Natural aluminium partition frame top and bottom with 3mm thick emboss decorative plywood boarding both side kept back to back ( Total thickness 6mm ) with necessary pop rivots, gasket and GI channels & etc. work complete in order. Sq.ft. 260.00

W 49

Sq.ft.

275.00

Full Board Partition with Aluminium Composite Panel W 50 Natural aluminium partition frame top and bottom with 4mm thick pvdf coated aluminium composite both side kept back to back ( Total thickness 8mm ) with necessary pop rivots, gasket and GI channels & etc. work complete in order. Natural aluminium partition frame top and bottom with 4mm thick polyester coated aluminium composite both side kept back to back ( Total thickness 8mm ) with necessary pop rivots, gasket and GI channels & etc. work complete in order. Sq.ft. 1870.00

W 51

Sq.ft.

800.00

Glazed & Board Partition with Emboss Decorative Plywood & 5mm Tinted Glass W 52 Natural aluminium partition frame top part with 5mm thick tinted glass and bottom part with 2.5mm thick emboss laminated plywood boarding both side kept back to back ( Total thickness 5mm ) with necessary pop rivots, gasket and GI channels & etc. work complete in order. Natural aluminium partition frame top part with 5mm thick tinted glass and bottom part with 3mm thick emboss decorative plywood boarding both side kept back to back ( Total thickness 6mm ) with necessary pop rivots, gasket and GI channels & etc. work complete in order. Natural aluminium partition frame top & bottom part with 2.5mm thick emboss laminated plywood boarding both side kept back to back ( Total thickness 5mm ) and middle part with 5mm thick tinted glass with necessary pop rivots, gasket and GI channels & etc. work complete in order. Natural aluminium partition frame top & bottom part with 3mm thick emboss decorative plywood boarding both side kept back to back ( Total thickness 6mm ) and middle part with 5mm thick tinted glass with necessary pop rivots, gasket and GI channels & etc. work complete in order. Sq.ft. 350.00

W 53

Sq.ft.

360.00

W 54

Sq.ft.

320.00

W 55

Sq.ft.

330.00

Engineering organization, W.P.

Page 70

BSR 2010

ITEM

DESCRIPTION Fully Glazed Partition with 5mm Tinted Glass

UNIT

RATE

W 56

Natural aluminium partition frame top and bottom with 5mm thick tinted glass with necessary pop rivots, gasket & etc. work complete in order.

Sq.ft.

360.00

Gypsum Board Partition W 57 Fabricating and installing gypsum board partitioning with necessary GI channel member frame work fixed on to wall and floors and 9mm thick gypsum board fixed to both sides of the frame work all completed with board joints taped and finished with gypsum compound to get wall finish. Rate to include for applying one coat of Acrylic filler to boards. Sq.ft. 315.00

Door Pull Handle W 58 Supplying and fixing " Hexzagon type "stainless steel door pull handle fixed complete to working order.(12" ) No. 3650.00

Door closer W 59 Supplying & fixing of heavy duty door closer of approved quality ( "Union" brand or equivalent ) and fixing to doors including all connecting works and making good after completion. (Guarantee Card from the local agent should be provided prior to installation) No. 5685.00

CEINING W 60 Supply and installation of Concealed type metal false ceiling of 600mm x 600mm out of 0.5mm average thickness epoxy powder painted steel sheets ( Paint film thickness of average 80 microns ) suspended to the roof frame work with hot dip galvanized " T " bars of 14mm x 38mm and wall angles of 19mm x 24mm suspended with 4mm dia. galvanized hanger rods. Supply and installation of Exposed grid type metal false ceiling of 600mm x 600mm out of 0.5mm average thickness epoxy powder painted steel sheets ( Paint film thickness of average 80 microns ) suspended to the roof frame work with hot dip galvanized " T " bars of 14mm x 38mm and wall angles of 19mm x 24mm suspended with 4mm dia. galvanized hanger rods. Sq.ft. 400.00

W 61

Sq.ft.

375.00

Engineering organization, W.P.

Page 71

BSR 2010

ITEM IRON GRILL W 62

DESCRIPTION

UNIT

RATE

Welded, Diamond shaped Iron grill, consisting 20mm x 6mm flat iron frame, 6mm dia M.S. rods at 3" centers to form 3"x6" diamond shape grill Rate shall include for fixing with No.10, 1" counter sunk iron screws and applying two coats of antiCorrosive paint. (Based on 2'-0"x4'-0" area) Welded, Diamond shaped Iron grill, consisting 20mm x 5mm flat iron frame, 5mm dia M.S. rods at 3" centers to form 3"x6" diamond shape grill Rate shall include for fixing with No.10, 1" counter sunk iron screws and applying two coats of antiCorrosive paint. (Based on 2'-0"x4'-0" area) Welded Diamond shaped iron grill, consisting 20mm x 6mm flat iron frame without joints, 20mm x 6mm mullions without joints, 20mm x 6mm isolated mid rails, 6mm dia. M.S. rods welded to form 3" x 6" diamond shaped isolated paneles. Rate shall include for fixing with No.10, 1" counter sunk iron screws and applying two coats of anti- Corrosive paint. (Based on 9'-0"x6'-0" area)

Sq.ft.

330.00

W 63

Sq.ft.

275.00

W 64

Sq.ft.

240.00

W 65

Welded Diamond shaped iron grill, consisting 20mm x 5mm flat iron frame without joints, 20mm x 5mm mullions without joints, 20mm x 5mm isolated mid rails,5mm dia. M.S. rods welded to form 3"x6" diamond shaped isolated paneles. Rate shall include for fixing with No.10, 1" counter sunk iron screws and applying two coats of anti- Corrosive paint. (Based on 9'-0"x6'0" area) Mild steel door 3'-0"x9"-0" high overall with 2'-3" high Iron grill on top consisting 1 1/2"x1 1/2"x4mm thick angle Iron door frame, 1/4" dia. mild steel grill on top (3"x6" diamond shape), 1"x1" M.S. Hollow section outer frame in sash with 2 No. 1"x1"x 3mm thick angle iron mid rail at 3'-0" hight, sheet gage 22 G.I. bottom panell, 6mm dia. mild steel rod grill on top panell , (3"x6" diamond shape)fix complete with 3No. 4"x4" M-S Butt Hinges tower bolt and Hasp and plate. Rate shall include for applying two coats of anti-Corrosive paint. Welded Diamond shaped iron grill, consisting 1" x 1" x 3mm angle iron frame 20mm x 6mm Mullions at 2'-0" centres.6mm dia. MS rods welded together to form 3" x 6" Diamond shape grill. Rate shall include for fixing with No.10, 1" counter sunk iron screws and applying two coats of anti-corrosive paint. Welded Diamond shaped iron grill, consisting 1" x 1" x 3mm angle iron frame 20mm x 5mm Mullions at 2'-0" centres.5mm dia. MS rods welded together to form 3" x 6" Diamond shape grill. Rate shall include for fixing with No.10, 1" counter sunk iron screws and applying two coats of anti-corrosive paint.

Sq.ft.

190.00

W 66

Sq.ft.

570.00

W 67

Sq.ft.

380.00

W 68

Sq.ft.

345.00

Engineering organization, W.P.

Page 72

BSR 2010

ITEM W 69

DESCRIPTION Welded Iron grill of rectangular pattern , consisting of a flat Iron frame of 25mm x 6mm with out intermediate joints, 2 nos of 25mm x 6mm horizontal members , 12mm dia. M.S. round bars as vertical members @ 4" c/c , vertical round bars to be drilled through horizontal flat Irons, fixed complete with counter sunk screws and rawl plugs to the masonry opening or timber. Rate shall include for applying two coats of anti-corrosive paint and two coats of enamal paint. ( for window openings of size 4'-0" x 2'-0" ). Details as per the Drawing No:- AR/DETAIL DRG/2010/01/10 & Sheet No. 05 COLLAPSIBLE DOOR

UNIT Sq.ft.

RATE 560.00

W 70

Fabricating and Installation of open type collapsible Iron door consisting with 20mm x 6mm flat iron codling cover and necessary screws, etc.. Rate shall include for applying two coats of anti-corrosive paint. ROLLER SHUTTERS & ROLLER DOORS

Sq.ft.

1100.00

W 71

Supply and fixing natural aluminium roller shutter consisting aluminium slats to the thickness of 1.2mm, centre bar, pulleys, side plate with the racers, fabricating the mechanical box with M.S. square tubes and covering the box and fixing on site with the bottom bars and necessary U channels. ( Approx. Size: 10'-6" width x 9'-8" high ) Supply and fixing powder coated zink alum roller doors consisting heavy duty powder coated aluminium slats bearing a thickness of 1.2mm and height of the slat to be 83mm, centre bar, pulleys, springs, dust seal, nylon strip, side plate with the racers & work complete in order. Supply and fixing the motor with two remotes for the roller shutter & roller door. MILD STEEL BALUSTRADE

Sq.ft.

625.00

W 72

Sq.ft.

625.00

W 73

Item

32400.00

W 74

Supplying , fabricating & fixing mild steel and timber hand rail, consisting of 16mm M.S. round bars @ 4" c/c as vertical members fixed to steps with the 8" x 1 1/2" x 1/2" thick M.S. plate connecting with 2 nos of 10mm anchor bolts, 4" x 2" approved timber rail fixed to 30mm x 6mm flat iron aling to the stair & 20mm x 6mm flat iron as the horizontal members to connecting the two vertical members finished smooth and work complete in order with necessary nuts & bolts. Rate Shall include for applying two coats of anti-corrosive paint and two coats of enamel paints. All sizes & details as per Drawing No:- AR/DETAIL DRG/2010/01/10 & Sheet No. 03 - Type 1-A

L.ft.

1805.00

Engineering organization, W.P.

Page 73

BSR 2010

ITEM W 75

DESCRIPTION

UNIT L.ft.

RATE 1975.00

Supplying , fabricating & fixing mild steel and timber hand rail, consisting of 16mm M.S. round bars @ 4" c/c as vertical members fixed to steps with the 8" x 1 1/2" x 1/2" thick M.S. plate connecting with 2 nos of 10mm anchor bolts, 4" x 2" approved timber decorative rail fixed to 30mm x 6mm flat iron aling to the stair & 20mm x 6mm flat iron as the horizontal members to connecting the two vertical members finished smooth and work complete in order with necessary nuts & bolts. Rate Shall include for applying two coats of anti-corrosive paint and two coats of enamel paints. All sizes and details as per Drawing No:AR/DETAIL DRG/2010/01/10 & Sheet No. 03 - Type 1-B Supplying , fabricating & fixing GI pipe hand rail, consisting of 2" dia. GI pipe as hand rail and 3/4" dia. GI pipes @ 11" c/c as vertical members fixed to steps with the 4" x 1 1/2" x 1/2" thick M.S. plate connecting with 2 nos of 10mm anchor bolts, work complete in order with necessary nuts & bolts. Rate Shall include for applying two coats of anticorrosive paint and two coats of enamel paints. All sizes and details as per Drawing No:- AR/DETAIL DRG/2010/01/10 & Sheet No. 04 - Type 2 Supplying , fabricating & fixing GI pipe hand rail top of the 9" thick brick wall ( Brick work measured separately ) consisting of 2" dia. GI pipe as hand rail and fixed to wall with 30mm x 6mm flat iron @ 18" c/c work complete in order. Rate Shall include for applying two coats of anticorrosive paint and two coats of enamel paints. All sizes and details as per Drawing No:- AR/DETAIL DRG/2010/01/10 & Sheet No. 04 - Type 3 Fabricate, supply and fix stainless steel pipe hand rail at staircase comprising 1 1/4" dia. uprights at 1'-0" c/c, 2" dia. top rail and 1" dia. middle rail. Uprights fixed to steps with 100 x 100 x 8mm thick S.S. base plate with 8mm dia. S.S. nuts and bolts complete as per working order. Y - STRUCTURAL STEEL WORK

W 76

L.ft.

1690.00

W 77

L.ft.

650.00

W 78

L.ft.

3700.00

Y 01

Supplying and fixing 2" x 2" x 5mm angle iron purling at maximum spacing of 4'-0" centers upto maximum span of 10'-0" including nuts, necessary bolds & washers etc. and application of two coats of anti-Corrosive paint. Supplying and fixing 2 1/2" x 2 1/2" x 5mm angle iron purling at maximum spacing of 4'-0" centers maximum span of 11'-0" (not less than 10'-0") for a asbestos purling roof without covering tiles on top. Rate shall include for necessary nuts, bolds & washers,etc. applying two coats of anti-Corrosive paint.

L.ft.

245.00

Y 02

L.ft.

285.00

Engineering organization, W.P.

Page 74

BSR 2010

ITEM Y 03

DESCRIPTION Supplying and fixing 3" x 3" x 5mm angle iron purling at maximum spacing of 4'-0" centers maximum span of 12'-0" (not less than 11'-0") for a asbestos purling roof without covering tiles on top. Rate shall include necessary nuts, olds & washers etc. , applying two coats of anti -Corrosive paint. Supplying and fixing 4" x 2" x 6mm channel Iron purling including two coats of anticorrosive paint up to 14'-0" span at 4'-0" c/c Supplying and fixing 5" x 2 1/2" x 6mm chanel Iron purling to existing Roof frame work , including two coats of anti-corrosive paint up to 16'-0" span, at 4'-0" c/c. Supplying and fixing 6" x 3" x 6mm channel Iron purling to existing Roof frame work , including two coats of anti-corrosive paint up to 18'-0" span at 4'-0"c/c. Supply and fixing double angles welded back to back as sleepers size 2" x 2" x 6mm ; Rate to include for two coats of anticorrosive paint and one coat of enamel paint. Supply and fixing double angles welded back to back as sleepers size 2 1/2" x 2 1/2" x 6mm ; Rate to include for two coats of anticorrosive paint and one coat of enamel paint. Supply and fixing double angles welded back to back as sleepers size 3" x 3" x 6mm ; Rate to include for two coats of anticorrosive paint and one coat of enamel paint. Mild steel Roof truss

UNIT L.ft.

RATE 375.00

Y 04

L.ft.

532.00

Y 05

L.ft.

860.00

Y 06

L.ft.

1010.00

Y 07

L.ft.

550.00

Y 08

L.ft.

650.00

Y 09

L.ft.

830.00

Y 10

Mild steel Roof truss for Calicut tile roofing (Maximum spacing 10'-0" ), 20'-0" span centre to centre, 25 pitch maximum and 18 pitch minimum with 4'-0" wide eaves at both sides, consisting of 2 No. 2" x 2" x 6mm angles as top and bottom chords. Rate shall include for struts and ties, gusset plates, base plates, sole plates, mild steel rag bolts, purling cleats & etc.. fabricating , transporting , hoisting , fixing in position and applying two coats of Zinc Phosphate paint, all details as per Drawing no:WP/TYPE/STR/2010/RT1 Mild steel Roof truss for Asbestos roofing (Maximum spacing 10'-0" ), 6 m (20'-0") span centre to centre, 12 pitch , with 4'-0" wide eaves at both sides, consisting of 2 No. 2" x 2" x 6mm angles as top and bottom chords. Rate shall include for struts and ties, gusset plates, base plates, sole plates, mild steel rag bolts, purling cleats & etc.. fabricating , transporting , hoisting , fixing in position and applying two coats of Zinc Phosphate paint, all details as per Drawing no:-WP/TYPE/STR/2010/RT2

No.

45000.00

Y 11

No.

43000.00

Engineering organization, W.P.

Page 75

BSR 2010

ITEM Y 12

DESCRIPTION Mild steel Roof truss for Calicut tile roofing(Maximum spacing 10'-0") 25'-0", span centre to centre 25 pitch maximum and 18 pitch minimum with 4'-0" wide eaves at both sides, consisting of 2 No. 2" x 2" x 6mm angles as top and bottom chords, 1 No. 2" x 2" x 6mm angles as struts and ties, 1/4" thick gusset plates, 3/8" thick. base plates, 3/4" dia M.S. Rag bolts of 12" long , 3" x 3" x 6mm size 1'-0" long purling cleats at 3'-6" centers and 2" x 2" x 16mm thick spacers at 2'-0" centers. Rate shall include for fabricating, transport, hoisting, fixing in position, and applying two coats of Zinc Phosphate paint. As per detail drg. No. 1190 school work branch.

UNIT No.

RATE 49000.00

Y 13

Mild steel Roof truss for Asbestos roofing (Maximum spacing 10'-0" ), 7.5 m (25'-0") span centre to centre, 12 pitch , with 4'-0" wide eaves at both sides, consisting of 2 No. 2 1/2" x 2 1/2" x 6mm angles as top and bottom chords. Rate shall include for struts and ties, gusset plates, base plates, sole plates, mild steel rag bolts, purling cleats & etc.. fabricating , transporting , hoisting , fixing in position and applying two coats of Zinc Phosphate paint, all details as per Drawing no:WP/TYPE/STR/2010/RT3 Mild steel roof truss for Asbestos roofing 9 m (30'-0") span , 12 pitch, comprising of 2 No. 65 x 65 x 6mm double angles as top and bottom welded with M.S. Plate of 65 x 65 x 8mm at 600mm intervals, and web member comprising of double angle of sizes 65 x 65 x 6mm and 50 x 50 x 6mm connected with 8mm thick mild steel gusset plate and 10mm thick base plate of 225 x 225 on either side and 10mm thick vertical gusset plate at the ends, 20mm dia. M.S. rag bolts of 400mm long. Rate shall include for fabricating, transport, hoisting, fixing in position, and including 2 coats of Zinc Phosphate paint and two coats of enamel paint. As per Drawing No. 1732 of School Work Division of Ministry of Education Mild steel roof truss for Calicut tile roofing 30'-0" span , 25 pitch maximum and 18 pitch minimum, consisting of 2 No. 2 1/2" x 2 1/2" x 6mm angles as top and bottom chords. Rate shall include for struts and ties, gusset plates, base plates, sole plates, mild steel rag bolts, purling cleats & etc.. fabricating , transporting , hoisting , fixing in position and applying two coats of Zinc Phosphate paint, all details as per Drawing no:WP/TYPE/STR/2010/RT4 Steel Scaffolding Set

No.

45000.00

Y 14

No.

78000.00

Y 15

No.

82000.00

Y 16

Supplying and erecting steel scaffolding sets. Rate to include for Set per day dismantling same after completion of work.

80.00

Engineering organization, W.P.

Page 76

BSR 2010

ITEM Zinc Alum Roofing Y 17 Y 18

DESCRIPTION

UNIT

RATE

Supplying and fixing zinc aluminium color bond standard ridge cap to existing sheet roof using new fasteners. Supply and fix proprietary coated zincalum gutter (minimum base metal thickness of sheet 0.4mm and minimum total thickness 0.47mm) complete with end caps, running joints etc. All joints to be properly connected with an adequate side laps not less than 225mm length and with sealant to ensure water tightness along the entire length of the gutter and including angle iron gutter brackets 25x25x3mm at 450mm centers with an adequate slope as directed and including application of two coats of each anticorrosive paint and enamel paint to all steel surfaces to match the gutter fix in position.( Inner size of 150mm x 175mm )

L.ft. L.ft.

310.00 525.00

Y 19

Supply and fix proprietary coated zincalum square down pipe (minimum base metal thickness of sheet 0.4mm and minimum total thickness 0.47mm) complete with necessary socket , elbow & bend. All joints to be properly connected and with sealant to ensure water tightness along the entire length. Down pipe brackets @ 1.0m c/c . Color bonded wall cladding 0.40mm thick fixed to external wall boxed out at down pipes including sills, flashing, removable sections at access points such as cleaning eyes etc. completely covering the surface as directed by the Engineer. Supply and fix Composite wall clading of 0.4mm thickness including inner frame work to vertical walls up to 30'-0". Rate shall include for scaffolding. Supply and lay double sided 3mm thick aluminium foil heat reflecting material to underside of roof supported with Gauge 10, 2" x 2" GI mesh. Supply and fix zinc alum profile roofing sheet (minimum base metal thickness of 0.4mm) and minimum thickness of 0.47mm, laid on existing purlings with joints to be properly connected with an adequate side lap to ensure water tightness along the entire length and complete to working order. Supply and fixing high tensile Galvanized iron "C" channels of 100 x 50 x 15 x 2.0mm thick Supply and fixing high tensile Galvanized iron "C" channels of 125 x 60 x 20 x 2.0mm thick Supply and fixing high tensile Galvanized iron "C" channels of 150 x 65 x 20 x 2.0mm thick

L.ft.

460.00

Y 20

Sq.ft.

285.00

Y 21

Sq.ft.

625.00

Y 22

Sqr.

6310.00

Y 23

Sqr.

16750.00

Y 24 Y 25 Y 26

L.ft. L.ft. L.ft.

335.00 385.00 420.00

Engineering organization, W.P.

Page 77

BSR 2010

ITEM

DESCRIPTION

UNIT

RATE

Z - MAINTANANCE WORK Demolishing
Z 01 Z 02 Z 03 Z 04 Z 05 Z 06 Z 07 Z 08 Z 09 Z 10 Z 11 Z 12 Z 13 Z 14 Z 15 Z 16 Demolishing reinforced cement concrete in suspended floors up to 4" thick , removing reinforcement and clearing debris. Demolishing cement concrete and clearing debris in floors from 4" to 6" thick floors. Demolishing reinforced cement, concrete in lintol of 9" x 6" removing reinforcement and clearing debris. Demolishing reinforced cement, concrete in lintol of 4 1/2"x 6" removing reinforcement and clearing debris. Demolishing brick piers, stacking brick and clearing debris away. Demolishing 9" thick brick walls stacking brick and clearing debris away. Demolishing 4 1/2" thick brick walls stacking brick and clearing debris away. Demolishing 3" thick brick paved floors and clearing debris away. Cube Cube L.ft. L.ft. Cube Cube Sqr. Sqr. 14275.00 6590.00 34.00 28.00 930.00 1130.00 425.00 550.00

Demolishing drains and clearing debris away. Demolishing rubble masonry built in cement and sand, stacking rubble and clearing debris away. Demolishing floor tiles and clearing debris away. Demolishing wall tiles and clearing debris away. Chipping cement rendering and clearing debris away. Chipping cement plastering and clearing debris away. Chipping lime plastering and clearing debris away. Chipping cement plaster in soffits and clearing debris away.

L.ft. Cube

19.00 1510.00

Sqr. Sqr. Sqr. Sqr. Sqr. Sqr.

1280.00 1035.00 820.00 565.00 280.00 850.00

Roof work
Z 17 Z 18 Z 19 Z 20 Removing and stacking calicut tile or half round tile from roof in single storied building. Removing and stacking calicut tile or half round tile from roof in two storied building. Removing and stacking calicut tile or half round tile from roof in three storied building. Removing and stacking corrugated asbestos sheet from roof in single storied building. Sqr. Sqr. Sqr. Sqr. 366.00 565.00 750.00 280.00

Engineering organization, W.P.

Page 78

BSR 2010

ITEM Z 21 Z 22 Z 23

DESCRIPTION Removing and stacking corrugated asbestos sheet from roof in two storied building. Removing and stacking corrugated asbestos sheet from roof in three storied building. Removing roof tiles/asbestos sheets and timber frame work, stacking serviceable materials and clearing debris away in single storied building. Removing roof tiles/asbestos sheets and timber frame work, stacking serviceable materials and clearing debris away in two storied building. Removing roof tiles/asbestos sheets and timber frame work, stacking serviceable materials and clearing debris away in three storied building. Removing and stacking calicut ridge tile. Removing and stacking asbestos ridging. Removing and stacking valance/Barge board materials and clearing debris away in single storied building. Removing and stacking valance/Barge board materials and clearing debris away in two storied building. Removing and stacking eaves gutter from roof of single storied buildings. Removing and stacking eaves gutter from roof of two storied building. Removing and stacking down pipes from roof of single storied building. Removing and stacking down pipe from roof of two storied building. Removing and stacking G.I. Valley gutter and flashing. Re-laying available calicut tiles on the roof in single storied building. Re-laying available calicut tiles on the roof in two storied building. Re-laying available calicut tiles on the roof in three storied building. Re-laying available asbestos sheets on the roof in single storied building. Re-laying available asbestos sheets on the roof in two storied building. Re-laying available asbestos sheets on the roof in three storied building.

UNIT Sqr. Sqr. Sqr.

RATE 375.00 470.00 755.00

Z 24

Sqr.

945.00

Z 25

Sqr.

1130.00

Z 26 Z 27 Z 28 Z 29 Z 30 Z 31 Z 32 Z 33 Z 34 Z 35 Z 36 Z 37 Z 38 Z 39 Z 40

L.ft L.ft L.ft L.ft L.ft L.ft L.ft L.ft

23.00 20.00 7.00 10.00 10.00 15.00 9.00 12.00

L.ft Sqr. Sqr. Sqr. Sqr. Sqr. Sqr.

20.00 375.00 470.00 565.00 605.00 755.00 905.00

Engineering organization, W.P.

Page 79

BSR 2010

ITEM Z 41 Z 42 Z 43 Z 44 Z 45 Z 46 Z 47 Z 48

DESCRIPTION Fixing available Reepers with wire nails. Fixing sorted out & cut to required size available timber to roof or other carpentry work. Fixing available corrugated asbestos sheet with hooks , nuts and bolts to roofing. Supply and fixing hooks, nuts & bolts for existing asbestos roof. Ridge tile bedded in lime cement motor 1:1:4 and coloured to match tiles.( Ridge tile available at site ) Fixing of available barge/Valance boards & fascia including cutting and minor repairs. Refixing existing G.I. Valley gutter and flashing including making good. Fixing of existing gutter and down pipe with making goods and including brackets.

UNIT L.ft C.ft Sqr. No L.ft L.ft L.ft L.ft

RATE 5.00 520.00 1215.00 26.00 73.00 18.00 58.00 30.00

Ceiling work
Z 49 Removing asbestos ceiling including timber frame work, stacking serviceable materials and clearing debris away in single storied building. Removing asbestos ceiling including timber frame work, stacking serviceable materials and clearing debris away in two storied building. Removing ceiling timber frame work,(with out asbestos sheet) stacking serviceable materiel and clearing debris away in single storied buildings. Removing ceiling timber frame work,(with out asbestos sheet) stacking serviceable materiel and clearing debris away in two storied buildings. Removing existing ceiling sheet stacking materials at the site and clearing debris away. Renewing in small quantities of 6" x 5/8" - 3/4" lunumidella ceiling including scaffolding up to 30'-0" hight. Fixing available lunumidella ceiling planks with new wire nails. Supplying and fixing 1 1/2" x 1/2" thick Beading , Halmilla or equivalant, planning & chamfering complete with brass screws. Sqr. 870.00

Z 50

Sqr.

1245.00

Z 51

Sqr.

205.00

Z 52

Sqr.

300.00

Z 53 Z 54

Sqr. L.ft

490.00 55.00

Z 55 Z 56

Sqr. L.ft.

1720.00 30.00

Doors & Windows
Z 57 Removing and stacking door sash only up to 40 S.ft from existing walls. No. 100.00

Engineering organization, W.P.

Page 80

BSR 2010

ITEM Z 58 Z 59 Z 60 Z 61 Z 62

DESCRIPTION Removing and stacking door sash only over 40 S.ft from existing walls. Removing and stacking door or window frame size up to 40 S.ft from existing walls. Removing and stacking door or window frame size over 40 S.ft from existing walls. Removing and stacking window sash only up to 40 S.ft from existing walls. Removing and stacking window sash only over 40 S.ft from existing walls. Removing and stacking trellis work Removing and stacking glass panes in doors, windows and fanlights. Renewing in short lengths with approved timber in existing door or window frames . Door or window frame altering existing rebate fillet using approved quality timber with screws and fixing available sashes.

UNIT No. No. No. No. No.

RATE 150.00 730.00 1100.00 100.00 150.00

Z 63 Z 64 Z 65 Z 66

Sq.ft. Sq.ft. L.ft. No.

10.00 31.00 380.00 1720.00

Z 67 Z 68 Z 69 Z 70 Z 71

Fixing available door or window frame. Fixing available door or window sash. Removing damage sashes of door or window and preparing & refixing. Supply and fixing Trellis work 1/2" x 1/2" laths with 2" apart diagonally, horizontally or vertically on existing timber framing. Supply and fixing 3mm thick glass panes for the existing door / window or fanlight sashes with approved timber beading.

Sq.ft. Sq.ft. Per sash Sq.ft. Sq.ft.

25.00 18.00 210.00 250.00 190.00

Sanitary
Z 72 Z 73 Z 74 Removing wash basin , sink or urinals including all fittings and making walls good. Removing squatting pan & standing types water closet with plugging sewer connection and reparing the wall & floor. Disconnecting flushing cistern and removing with plugging water connection and making good of all damaged walls, floors & etc. No. No. No. 245.00 1000.00 850.00

Z 75 Z 76 Z 77

Removing 1/2" to 1 1/2" dia. bib tap or stop cock. Fixing available ball valve. Fixing lavatory type basin to existing brackets. ( Tap , waste pipe and basin are available)

No. No. No.

34.00 100.00 830.00

Engineering organization, W.P.

Page 81

BSR 2010

ITEM Z 78

DESCRIPTION Fixing of wash basin, leveling and connecting to existing water connections and making good (Basin, bracket and fittings are available) Repairing bib taps and stop cocks by fixing leather washers. Removing & repairing pillar tap and re-fixing to the wash basin carefully without any damaged.

UNIT No.

RATE 1080.00

Z 79 Z 80

No. No.

105.00 170.00

Painting
Z 81 Z 82 Z 83 Z 84 Removing painting from walls and clearing debris away. Removing enamel paint from door or window frame and clearing debris away. Removing paint from painted glass panes with caustic soda solution or other paint remover. Removing water proof treatment or hot bitumen from floors or flat roof and clearing debris away. Painting ceiling beading with two coats of enamal paint. Sqr. Sqr. Sq.ft. Sqr 375.00 750.00 26.00 1465.00

Z 85

L.ft

12.00

Electrical
Z 86 Z 87 Z 88 Z 89 Z 90 Z 91 Z 92 Z 93 Supply & replacing one gang one way switch without wiring including removing old one. Supply & replacing two gang one way switch without wiring including removing old one. Supply & replacing three gang one way switch without wiring including removing old one. Supply & replacing four gang one way switch without wiring including removing old one. Supply & replacing five gang one way switch without wiring including removing old one. Supply & replacing 5 Amp. Switch socket outlet without wiring including removing old one. Supply & replacing 15 Amp. Switch socket outlet without wiring including removing old one. Supply & replacing 13 Amp. Switch socket outlet without wiring including removing old one. No. No. No. No. No. No. No. No. 100.00 175.00 250.00 330.00 410.00 160.00 435.00 300.00

Other
Z 94 Z 95 Z 96 Supplying and placing 4" dia.PVC (Type 250) wheep holes. Removing existing mortice lock repairing and re-fixing. Removing and stacking aluminium frame partition. L.ft No Sq.ft. 130.00 330.00 8.00

Engineering organization, W.P.

Page 82

BSR 2010

ITEM

DESCRIPTION

UNIT

RATE

Transporting
Z 97 Z 98 Transporting debris cleared away from site by tractor (approx.. 10 Miles away). Transporting debris cleared away from site by 3.5 Cubes capacity heavy vehicle. Rate to inclusive of loading with JCB machine (approx.. 20 Miles away). Per Load Per Load 2200.00 4500.00

AA - MISCELLANEOUS

The following AA 01 & AA 02 items are exclusively for estimating purposes for which a standard work norm is not immediately available and at the same time it is impossible to arrive at a realistic break-up of labour component involved at the time of preparation of the estimate. The rate is not to be used for engaging labourers on routine work and the mere appearance of this rate on BSR is not a sanction to pay the daily labourers at this rate. Skilness of the Craftman to be verified by a trade test certificate at the time of engagement. AA 01 Engaging special skilled labour services in the trades of fitter, Per 8 Hour electrician, welder, mason, carpenter, bar bender, painter on 8 day Per hour day basis. Person AA 02 Engaging labour services in un-skilled category of any type of Per 8 Hour manual work on a 8 hour day basis. day Per Person AA 03 Pumping water using 2" dia. water pump. P.V.C. Coated Chain Link Fence AA 04 Supplying & fixing PVC coated G.I. chain link fence (2" x 2") of gauge 10 height of 8'-0" for GI pipe fixed with available 20mm x 6mm flat iron ( GI pipe & flat iron measured separately) complete with tension J bolts and tension cords. AA 05 Supplying & fixing PVC coated G.I. chain link fence (2" x 2") of gauge 10 height of 10'-0" for GI pipe fixed with available 20mm x 6mm flat iron ( GI pipe & flat iron measured separately) complete with tension J bolts and tension cords. AA 06 Supplying and fixing 2" dia.x 3.6mm thick Medium quality GI pipe 8'-0" clear height with excavation 1'-0"x 1'-0"x 3'-0" cement concrete base 1:2 1/2:5 (1") with 1/2" dia. MS rods welded to bottom of G.I. Pipe and drilling 7 Nos. holes to fixed the chain link (chain link measured separately) and fiberglass coping on top. Rate to include for application of one coat of anticorrosive paint and two coats of enamel paint. Sq.ft. 84.00 Per 8 Hour Day 885.00

732.00

2440.00

Sq.ft.

77.00

L.ft.

615.00

Engineering organization, W.P.

Page 83

BSR 2010

ITEM

DESCRIPTION

UNIT L.ft.

RATE 575.00

AA 07 Supplying and fixing 2" dia.x 3.6mm thick Medium quality GI pipe 10'-0" clear height with excavation 1'-0"x 1'-0"x 3'-0" cement concrete base 1:2 1/2:5 (1") with 1/2" dia. MS rods welded to bottom of G.I. Pipe and drilling 7 Nos. holes to fixed the chain link (chain link measured separately) and fiberglass coping on top. Rate to include for application of one coat of anticorrosive paint and two coats of enamel paint. AA 08 Supplying and fixing 3" dia.x 4mm thick Medium quality GI pipe 8'-0" clear height with excavation 1'-0"x 1'-0"x 3'-0" cement concrete base 1:2 1/2:5 (1") with 1/2" dia. MS rods welded to bottom of G.I. Pipe and drilling 7 Nos. holes to fixed the chain link (chain link measured separately) and fiberglass coping on top. Rate to include for application of one coat of anticorrosive paint and two coats of enamel paint. AA 09 Supplying and fixing 3" dia.x 4mm thick Medium quality GI pipe 10'-0" clear height with excavation 1'-0"x 1'-0"x 3'-0" cement concrete base 1:2 1/2:5 (1") with 1/2" dia. MS rods welded to bottom of G.I. Pipe and drilling 7 Nos. holes to fixed the chain link (chain link measured separately) and fiberglass coping on top. Rate to include for application of one coat of anticorrosive paint and two coats of enamel paint. AA 10 Supplying and fixing 20mm x 6mm flat iron to existing GI pipe (GI pipe measured separately) to fix the chain link, Rate inclusive of drilling 09 Nos. holes of 6mm dia. Rate to include for application of one coat of anticorrosive paint and two coats of enamel paint. AA 11 Supplying and fixing 1 1/4"x 1 1/4"x 6mm angle iron horizontal bracings welded to existing GI pipes. Rate to include for application of one coat of anticorrosive paint and two coats of enamel paint. AA 12 Supplying and fixing 1" dia. x 3.2mm thick GI pipe horizontal bracings welded to existing GI pipes. Rate to include for application of one coat of anticorrosive paint and two coats of enamel paint. Barbed Wire Fence AA 13 Supplying & fixing 14 gauge galvanized barbed wire 4 points, 3" apart on pre-cast concrete posts with hook bolts including straining. ( Concrete Posts paid seperately) AA 14 Supplying & fixing pre-cast concrete Intermediate Posts of size (5" x 5") - (3" x 3") & 5'-9" high for 7 strands including necessary excavation and concreting at the placing. AA 15 Supplying & fixing pre-cast concrete End Posts of size (5" x 5") & 6'-3" high for 7 strands including necessary excavation and concreting at the placing.

L.ft.

870.00

L.ft.

830.00

L.ft.

110.00

L.ft.

220.00

L.ft.

235.00

L.ft.

10.00

No.

990.00

No.

1555.00

Engineering organization, W.P.

Page 84

BSR 2010

ITEM

DESCRIPTION

UNIT No.

RATE 1075.00

AA 16 Supplying & fixing pre-cast concrete Struts of size (5" x 4") - (3" x 3") & 6'-5" high for 7 strands including necessary excavation and concreting at the placing. AA 17 Supplying & fixing pre-cast concrete Intermediate Posts of size (5" x 5") - (3" x 3") & 6'-9" high for 8 strands including necessary excavation and concreting at the placing. AA 18 Supplying & fixing pre-cast concrete End Posts of size (5" x 5") & 7'-3" high for 8 strands including necessary excavation and concreting at the placing. AA 19 Supplying & fixing pre-cast concrete Struts of size (5" x 4") - (3" x 3") & 7'-5" high for 8 strands including necessary excavation and concreting at the placing. AA 20 Supplying & fixing pre-cast concrete Intermediate Posts of size (5" x 5") - (3" x 3") & 7'-9" high for 9 strands including necessary excavation and concreting at the placing. AA 21 Supplying & fixing pre-cast concrete End Posts of size (5" x 5") & 8'-3" high for 9 strands including necessary excavation and concreting at the placing. AA 22 Supplying & fixing pre-cast concrete Struts of size (5" x 4") - (3" x 3") & 8'-5" high for 9 strands including necessary excavation and concreting at the placing. AA 23 Supplying & fixing pre-cast concrete Intermediate Posts of size (5" x 5") - (3" x 3") & 7'-7" + 1'-6" high for 12 strands including necessary excavation and concreting at the placing. AA 24 Supplying & fixing pre-cast concrete End Posts of size (5" x 5") & 8'-1" + 1'-6" high for 12 strands including necessary excavation and concreting at the placing. AA 25 Supplying & fixing pre-cast concrete Struts of size (5" x 4") - (3" x 3") & 8'-1" + 1'-6" high for 12 strands including necessary excavation and concreting at the placing.

No.

1055.00

No.

1950.00

No.

1130.00

No.

1280.00

No.

2230.00

No.

1275.00

No.

1585.00

No.

2795.00

No.

2335.00

AB - LANDSCAPINGS
Turfing AB 01 Supply , laying & turfing Buffalo grass after the levelling ground with necessary soil filling and laying refuse of coir layer and watering. Also fertilizing with using waer and maintain the turfing area for a 1 year period. AB 02 Supply , laying ,turfing & planting Blue grass after the levelling ground with necessary soil filling and laying refuse of coir layer and watering. Also fertilizing with using waer and maintain the turfing area for a 1 year period. ROOT BOLL PLANTS AB 03 Supply & Planting maximum 5'-0" girth and 10'-0" - 12'-0" high Atteria Plant with the fertilizing , watering & plant should be maintain for a 1 year period. No. 5400.00 Sq.ft. 40.00

Sq.ft.

130.00

Engineering organization, W.P.

Page 85

BSR 2010

ITEM

DESCRIPTION

UNIT No.

RATE 5400.00

AB 04 Supply & Planting maximum 5'-0" girth and 10'-0" - 12'-0" high Ehala with the fertilizing , watering & plant should be maintain for a 1 year period. AB 05 Supply & Planting maximum 5'-0" girth and 10'-0" - 12'-0" high Araliya Plant with the fertilizing , watering & plant should be maintain for a 1 year period. AB 06 Supply & Planting maximum 5'-0" girth and 10'-0" - 12'-0" high Kiripalu Plant with the fertilizing , watering & plant should be maintain for a 1 year period. AB 07 Supply & Planting maximum 5'-0" girth and 7'-0" - 8'-0" high Foxtail Palm with the fertilizing , watering & plant should be maintain for a 1 year period. AB 08 Supply & Planting maximum 5'-0" girth and 8'-0" - 10'-0" high Kentiya Palm with the fertilizing , watering & plant should be maintain for a 1 year period. AB 09 Supply & Planting maximum 5'-0" girth and 6'-0" - 8'-0" high Red Palm with the fertilizing , watering & plant should be maintain for a 1 year period. AB 10 Supply & Planting maximum 5'-0" girth and 6'-0" - 8'-0" high Queen Palm with the fertilizing , watering & plant should be maintain for a 1 year period. Paving Blocks AB 11 Supply & paving 100mm thick Uni-Natura precast interlocking paving blocks of 40 N/mm2 compressive strengh , manufactured by "Sehda Lanka Ltd." or approved equivelant, on 2" thick compacted quarry dust bed laid on top of a well compacted earth sub base for the high volume traffic areas. ( Colour of block should be approved by Architect. ) AB 12 Supply & paving 100mm thick Uni-Flora precast interlocking paving blocks of 40 N/mm2 compressive strengh , manufactured by "Sehda Lanka Ltd." or approved equivelant, on 2" thick compacted quarry dust bed laid on top of a well compacted earth sub base for the high volume traffic areas. ( Colour of block should be approved by Architect. ) AB 13 Supply & paving 80mm thick Uni-Natura precast interlocking 2 paving blocks of 15 N/mm compressive strengh , manufactured by "Sehda Lanka Ltd." or approved equivelant, on 2" thick compacted quarry dust bed laid on top of a well compacted earth sub base for the Low volume traffic areas or Pedestrian areas. ( Colour of block should be approved by Architect. )

No.

5400.00

No.

5400.00

No.

6500.00

No.

3250.00

No.

4300.00

No.

6500.00

Sqr.

27330.00

Sqr.

30275.00

Sqr.

24250.00

Engineering organization, W.P.

Page 86

BSR 2010

ITEM

DESCRIPTION

UNIT Sqr.

RATE 27070.00

AB 14 Supply & paving 80mm thick Uni-Flora precast interlocking paving blocks of 15 N/mm2 compressive strengh , manufactured by "Sehda Lanka Ltd." or approved equivelant, on 2" thick compacted quarry dust bed laid on top of a well compacted earth sub base for the Low volume traffic areas or Pedestrian areas. ( Colour of block should be approved by Architect. )

AB 15 Supply & paving 60mm thick Uni-Natura precast interlocking paving blocks of 15 N/mm2 compressive strengh , manufactured by "Sehda Lanka Ltd." or approved equivelant, on 2" thick compacted quarry dust bed laid on top of a well compacted earth sub base for the Low volume traffic areas or Pedestrian areas. ( Colour of block should be approved by Architect. ) AB 16 Supply & paving 60mm thick Uni-Flora precast interlocking paving blocks of 15 N/mm2 compressive strengh , manufactured by "Sehda Lanka Ltd." or approved equivelant, on 2" thick compacted quarry dust bed laid on top of a well compacted earth sub base for the Low volume traffic areas or Pedestrian areas. ( Colour of block should be approved by Architect. ) AB 17 Supply & paving Dutch-Natura precast interlocking paving blocks of 15 N/mm2 compressive strengh , manufactured by "Sehda Lanka Ltd." or approved equivelant, on 2" thick compacted quarry dust bed laid on top of a well compacted earth sub base for the Low volume traffic areas or Pedestrian areas. ( Colour of block should be approved by Architect. ) AB 18 Supply & paving Dutch-Floara precast interlocking paving blocks of 15 N/mm2 compressive strengh , manufactured by "Sehda Lanka Ltd." or approved equivelant, on 2" thick compacted quarry dust bed laid on top of a well compacted earth sub base for the Low volume traffic areas or Pedestrian areas. ( Colour of block should be approved by Architect. ) AB 19 Supply & paving Camino-Natura precast interlocking paving blocks of 15 N/mm2 compressive strengh , manufactured by "Sehda Lanka Ltd." or approved equivelant, on 2" thick compacted quarry dust bed laid on top of a well compacted earth sub base for the Low volume traffic areas or Pedestrian areas. ( Colour of block should be approved by Architect. ) AB 20 Supply & paving Camino-Floara precast interlocking paving blocks of 15 N/mm2 compressive strengh , manufactured by "Sehda Lanka Ltd." or approved equivelant, on 2" thick compacted quarry dust bed laid on top of a well compacted earth sub base for the Low volume traffic areas or Pedestrian areas. ( Colour of block should be approved by Architect. )

Sqr.

22715.00

Sqr.

25280.00

Sqr.

25150.00

Sqr.

28350.00

Sqr.

23740.00

Sqr.

26300.00

Engineering organization, W.P.

Page 87

BSR 2010

ITEM

DESCRIPTION

UNIT Sqr.

RATE 22200.00

AB 21 Supply & paving Wintage-Natura precast interlocking paving blocks of 15 N/mm2 compressive strengh , manufactured by "Sehda Lanka Ltd." or approved equivelant, on 2" thick compacted quarry dust bed laid on top of a well compacted earth sub base for the Low volume traffic areas or Pedestrian areas. ( Colour of block should be approved by Architect. ) AB 22 Supply & paving Wintage-Floara precast interlocking paving blocks of 15 N/mm2 compressive strengh , manufactured by "Sehda Lanka Ltd." or approved equivelant, on 2" thick compacted quarry dust bed laid on top of a well compacted earth sub base for the Low volume traffic areas or Pedestrian areas. ( Colour of block should be approved by Architect. ) AB 23 Supply & paving Dobler-Natura precast interlocking paving 2 blocks of 15 N/mm compressive strengh , manufactured by "Sehda Lanka Ltd." or approved equivelant, on 2" thick compacted quarry dust bed laid on top of a well compacted earth sub base for the Low volume traffic areas or Pedestrian areas. ( Colour of block should be approved by Architect. ) AB 24 Supply & paving Dobler-Floara precast interlocking paving blocks of 15 N/mm2 compressive strengh , manufactured by "Sehda Lanka Ltd." or approved equivelant, on 2" thick compacted quarry dust bed laid on top of a well compacted earth sub base for the Low volume traffic areas or Pedestrian areas. ( Colour of block should be approved by Architect. ) AB 25 Supply & paving Pietra-Natura precast interlocking paving blocks of 15 N/mm2 compressive strengh , manufactured by "Sehda Lanka Ltd." or approved equivelant, on 2" thick compacted quarry dust bed laid on top of a well compacted earth sub base for the Low volume traffic areas or Pedestrian areas. ( Colour of block should be approved by Architect. ) AB 26 Supply & paving Pietra-Floara precast interlocking paving 2 blocks of 15 N/mm compressive strengh , manufactured by "Sehda Lanka Ltd." or approved equivelant, on 2" thick compacted quarry dust bed laid on top of a well compacted earth sub base for the Low volume traffic areas or Pedestrian areas. ( Colour of block should be approved by Architect. ) CONCRETE CURB AB 27 Supply & paving pre cast concrete Curb ( Small ) of size 540mm x 175mm manufactured by "Sehda Lanka Ltd." or approved equivelant, with 1:3 cement mortar on top of a well compacted earth sub base. AB 28 Supply & paving pre cast concrete Curb ( Half ) of size 450mm x 255mm manufactured by "Sehda Lanka Ltd." or approved equivelant, with 1:3 cement mortar on top of a well compacted earth sub base.

Sqr.

24125.00

Sqr.

22200.00

Sqr.

24510.00

Sqr.

26300.00

Sqr.

29250.00

L.ft.

350.00

L.ft.

530.00

Engineering organization, W.P.

Page 88

BSR 2010

ITEM

DESCRIPTION

UNIT L.ft.

RATE 525.00

AB 29 Supply & paving pre cast concrete Curb ( Full ) of size 915mm x 255mm manufactured by "Sehda Lanka Ltd." or approved equivelant, with 1:3 cement mortar on top of a well compacted earth sub base. CEMENT POTS AB 30 Supply & placing of 12" dia. Cement pots 4'-0" high ( size approximate ) AB 31 Supply & placing of 18" dia. Cement pots 4'-0" high ( size approximate ) AB 32 Supply & placing of 24" dia. Cement pots 4'-0" high ( size approximate ) AB 33 Supply & placing of 28" dia. Cement pots 4'-0" high ( size approximate ) AB 34 Supply & placing of 48" dia. Cement pots 4'-0" high ( size approximate )

No. No. No. No. No.

1400.00 2600.00 3400.00 6800.00 9100.00

Engineering organization, W.P.

Page 89

BSR 2010