Canon LIDE 20 Scanner Disassembly Goat Strings

Published on May 2017 | Categories: Documents | Downloads: 21 | Comments: 0 | Views: 333
of 11
Download PDF   Embed   Report

Comments

Content


← Meds 2011 Intro to Teaching →
Posted by Posted by gatohaus gatohaus
Image by awrose via Flickr
JUN15
Canon LIDE 20 Scanner Disassembly
Tips on taking a Canon Canoscan LIDE 20 apart. ( In most of these pictures I have already taken
the scanner apart at least once.)
PAGE_STATUS: Draft.
Should break this into parts.
I’m hoping to make a tolerable large format digital camera back for an 8×10″ field camera by
modifying a Canon LIDE scanner.
The LIDE scanners are:
very common
supported by open-source drivers
very cheap on the used market
are connected by a single usb cable for both power and data
easily powered by a netbook
lightweight
a long-lived series with steady incremental improvements
lessons learned on one series apply almost directly to most others
Overview
The general idea is to strip out the optics and slap the scanner on
the back of a field camera.
The sensor is a linear array with a lenslet strip positioned directly in
front of it. This strip will be removed, leaving the sensor at the
bottom of a deep, dark channel with a narrow field of view in the
scanning direction. As the sensor moves across the image plane,
the incident rays will be occluded by the channel for a large portion
of the scan. So the channel must be widened. This might be tricky
as the sensor is glued to the structure, cannot tolerate any flexure,
and should not be touched by debris.
The light source normally use to illuminate the object being scanned will need to be removed,
disabled, or at least covered.
The LIDE’ scanners use the glass platen itself as support for the sensor housing. I would like to
remove the glass but there must be something to support the sensor housing. Maybe a large
rectangle can be cut out of the glass.. or two strips cut out for the guides.
The last bit of hardware is to mount the scanner onto the camera. I’ll get everything else settled
before worrying about this to much.
Software.
Even the Canon drivers will continue to work until you yank out the light source. Once it’s out the
CATEGORIES CATEGORIES
Choosing (10)
obselete (2)
emo (11)
Events (4)
ideas (5)
mental health notes (6)
teaching (6)
Viewpoints (8)
GO GO
GOAT STRINGS GOAT STRINGS
emo-tech
HOME HOME ABOUT ABOUT
Canon LIDE 20 Scanner Disassembly | Goat Strings 05.05.2014
http://gatohaus.wordpress.com/2011/06/15/canon-lide-20-scanner-disassembly/ 1 / 11
driver may just return a scanner failure notice, or lamp failure, or calibration failure. Afterward you’ll
need to use something like SANE‘s free , open source drivers (assuming you’re using Linux). In the
end you’ll either need to some basic programming using something like the underlying bits of SANE
or you can buy a copy of VueScan. VueScan is available not only for Linux but even for more
obscure systems like Mac or even Windows. And yes, it’s worth it.
The part I haven’t started at all yet is building the image chain for this beast. Shouldn’t be too
hard.
Imaging Expectations
It’s gonna be noisy. Anything in the scene that moves will be distorted (linear array). B&W only.
No idea where the sensor cuts off… ~360nm to ??~1100nm??… maybe 900.. dunno. Unsure if
integration time varies with scanning settings or if it’s just fixed. Scan times for older models
~1min, newer models ~8sec. Output image: TIF up to 19000×26000 pixels, at ?10bit. Unsure
about bitdepth.. Canon claims 16b, but I’ll call BS on that. It’ll depend on the noise. Wouldn’t be
surprised if it was only 6 or 7 bit in the end.
Begin disassembly
Here’s the scanner, minus the cover. The cover is easy to remove by simply flexing the hinge a
bit. -v2 Well, on the LIDE 25 it took a lot more pressure than the LIDE 20.
Remove platen retainers
A plastic retainer runs down each long side of the platen. They stop the platen from sliding forward
which would free it. There are no screws. The plastic strips are held in place with tape along most of
their length.
Canon LIDE 20 Scanner Disassembly | Goat Strings 05.05.2014
http://gatohaus.wordpress.com/2011/06/15/canon-lide-20-scanner-disassembly/ 2 / 11
Begin at the front of the scanner and pry up the ‘ovals’.
You can see coming at the sides of the ovals is a good place to work. (I initially started at the very
end.)
Canon LIDE 20 Scanner Disassembly | Goat Strings 05.05.2014
http://gatohaus.wordpress.com/2011/06/15/canon-lide-20-scanner-disassembly/ 3 / 11
Pull gently while slipping something underneath to separate the tape from the plastic. As I’m
planning on removing the platen permanently, scratches were not a concern.
One strip off, one to go.
Canon LIDE 20 Scanner Disassembly | Goat Strings 05.05.2014
http://gatohaus.wordpress.com/2011/06/15/canon-lide-20-scanner-disassembly/ 4 / 11
With both retaining strips gone, the platen will slide back with moderate pressure. Once back, the
platen can be removed entirely.
Sensor and platform details
Move the platform toward the middle of the scanner. I did this by pulling the cable mid-scan. Ugly,
but I haven’t had any problems. Notice the ‘rod’ and the ‘string’.
Canon LIDE 20 Scanner Disassembly | Goat Strings 05.05.2014
http://gatohaus.wordpress.com/2011/06/15/canon-lide-20-scanner-disassembly/ 5 / 11
WARNING: There are two, free-floating plastic glides on the top of the platform. Collect these
now.
Drive string
The ‘string’ is freed by unlocking the endpiece where the spring sits. On the bottom of the scanner
(be sure not to turn the scanner over), next to the platform lock, you’ll see a small, round hole.
Insert say a small screw driver and push gently to allow this ‘string lock’ to be freed. While pushing
the screw driver, slide the string lock free.
Canon LIDE 20 Scanner Disassembly | Goat Strings 05.05.2014
http://gatohaus.wordpress.com/2011/06/15/canon-lide-20-scanner-disassembly/ 6 / 11
You can carefully flip the platform over to see how the string runs through the gears. Separate the
string from the platform. Be sure not to kink the string.
Sensor package removal
WARNING: There is a small spring underneath the sensor package. It will come free as you
remove the package.
Canon LIDE 20 Scanner Disassembly | Goat Strings 05.05.2014
http://gatohaus.wordpress.com/2011/06/15/canon-lide-20-scanner-disassembly/ 7 / 11
The sensor package pivots on a hinge on the platform. It can be worked free with very little
pressure as it slides to unlock when slightly elevated.
Sensor detail
Here you can see the light guide and the lenslet strip. In this picture the light guide is just above the
screwdriver tip and the lenslet strip is one of the black horizontal pieces. There’s a better shot of
the lenslet placement a few pics below.
Here is the LED used to illuminate objects during scans. It seemed to be just butted against the
light guide without adhesive.
Light guide removal
Canon LIDE 20 Scanner Disassembly | Goat Strings 05.05.2014
http://gatohaus.wordpress.com/2011/06/15/canon-lide-20-scanner-disassembly/ 8 / 11
This is easier than I had expected. I gave each of the attachment points a gentle prying. Not
enough to really see any movement. Then started prying at the end opposite the LED, switching
to just pulling with my fingers as soon as I could get a hold.
Lenslet removal
Like the light guide, the lenslet strip is easy to pry out. The strip will be discarded, the only real
concern is with possible damaging the sensor directly below while removing the strip.
WARNING: There is nothing protecting the sensor but this lenslet strip.
A note on cleaning the sensor… Don’t worry about a bit of dust getting on the linear array. But do
make sure that your tools and particles of plastic created while working keep clear of the sensor. If
you wish to clean the sensor use air. A small squeeze bulb is perfect. Do NOT use those old cans of
compressed “air” from back in the film camera days. They contain chemicals that can contaminate
the senor’s silicon.
Ha! That turned out to be a non-issue. The sensor is embedded within some form of clear plastic
or something similar. (pics and description coming soon)


LIDE 25

Related articles
VueScan 9 Versatile Scanner Software: Better than Ever, Charles W. Moore, Miscellaneous
Ramblings (lowendmac.com)
Share this:
1 1

Related
The phone / netbook dilemma
Trying available GPS games
Microscopes for Third Graders
Canon LIDE 20 Scanner Disassembly | Goat Strings 05.05.2014
http://gatohaus.wordpress.com/2011/06/15/canon-lide-20-scanner-disassembly/ 9 / 11
← Meds 2011 Intro to Teaching →
Posted on 15 June 2011, in ideas and tagged camera, flesh this out, Large Format, photog, scanner
camera, VueScan. Bookmark the permalink. 9 Comments.
LEAVE A COMMENT LEAVE A COMMENT COMMENTS 9 COMMENTS 9
the little spring in the cover open/close mechnism loose with me. would you happen to
have a photo which shows how to reassemble this spring again?
thanks
twingo | 30 September 2011 at 00:22
Sorry, but I tossed the cover right at the start.
gatohaus gatohaus | | 5 5 January 2012 at 00:38 January 2012 at 00:38
Did you get anywhere with this project? I use a similar setup. I would like to discuss
scanner cameras with you. You can see my work at http://www.sederburns.com.
Seder | 30 December 2011 at 16:55
Hi. I did get the point of testing it a bit and capturing images last Fall, and
promptly got distracted. I should update this and wouldn’t mind working some
more on the camera.
Your gallery pics look great! Interesting use of time. Definitely things I’d never
considered before.
I wouldn’t mind knowing more about your camera(s).
It probably would be non-difficult to remove some of the sensor noise (the
horizontal streaks) but I like them as is.
gatohaus gatohaus | | 5 5 January 2012 at 00:37 January 2012 at 00:37
Thank u so much! got my scanner fixed in 20 minutes with this manual. You safed my
ass and made my day. TANKS a LOT!
Manfred | 3 August 2012 at 12:27
thanx buddy you have helped me in assembling it thank you very much for your
unintentional work for me
Vikalp Gupta | 7 November 2012 at 09:11
Hello and very interesting, looking at trying to make a x-ray scanner out of my Canon
scanner. Have you gotten any further on the project, I wish to disable the light source
and use the detector as the x-ray sensor and scan the image. Can you recommend the
best open source software to do this. Thank you for any help you might be able to
Cliff Schuring | 22 August 2013 at 19:03
Canon LIDE 20 Scanner Disassembly | Goat Strings 05.05.2014
http://gatohaus.wordpress.com/2011/06/15/canon-lide-20-scanner-disassembly/ 10 / 11
Leave a Reply
Blog at WordPress.com. The Mystique Theme.
provide to make this easier
To remove the plate, NOT NEED UNSTICK SIDE BARS FROM THE GLASS!!!! Use a
screwdriver to lift them from the hinge cover side, releasing the 2 tabs from the slots,
keep them raised above the rear frame and then push the glass forward with the 2
sidebars glued. For subsequent interventions you can short the 2 tabs of half a
millimeter. Rino
Rino | 20 September 2013 at 10:06
The black and white string of my canon canoscan lide 20 was broken.. Can I replace it?
Where can I buy that string?
Aisa | 26 September 2013 at 06:23
Enter your comment here... Enter your comment here...
Follow Follow
Canon LIDE 20 Scanner Disassembly | Goat Strings 05.05.2014
http://gatohaus.wordpress.com/2011/06/15/canon-lide-20-scanner-disassembly/ 11 / 11

Sponsor Documents

Or use your account on DocShare.tips

Hide

Forgot your password?

Or register your new account on DocShare.tips

Hide

Lost your password? Please enter your email address. You will receive a link to create a new password.

Back to log-in

Close