Custom 1911
Content
1911 CUSTOM SERVICES 1911-A1 Accurizing Package: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $895.00 1. Tighten slide to frame 2. Acc-U-Rail option, additional $100 charge 3. Fit custom match barrel system (barrel & bushing or bull barrel) Ramped barrel, additional $100 charge 4. Install custom match hammer & sear 5. Fit match aluminum trigger 6. Polish feed ramp 7. Throat barrel 8. Tune extractor & ejector 9. Deburr pistol internally 10. Refinish as needed (Additional charge for some finishes) 11. Inspect & test fire for function 1911-A1 Reliability Package: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $150.00 1. Deburr pistol internally 2. Tune extractor and ejector 3. Recut barrel throat and polish feed ramp 4. Check headspace 5. Polish breechface 6. Inspect and test fire for function This package does not include installation of an extended ejector or lower and flare of ejection port on GI models. 1911-A1 Defense Package: GI models:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $350.00 Other Springfield models: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $260.00 1. Deburr pistol internally 2. Tune extractor & ejector 3. Recut barrel throat & polish feed ramp 4. Install custom match bushing 5. Check headspace 6. Install new recoil spring & firing pin spring 7. Tuned 4.5 lb. trigger 8. GI Models: Lower & flare ejection port; install extended ejector 9. Refinish as needed (Additional charge for some finishes) 10. Reliability tuning 11. Inspect & test fire for function 1911-A1 Loaded Package: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $895.00 1. Novak style low mount rear sight with 2 green dot tritium inserts 2. Dovetail front sight with green tritium insert 3. Lightweight aluminum trigger 4. Extended ambidextrous thumb safety 5. Flat checkered mainspring housing (ILS) 6. Beavertail grip safety 7. Skeletonized delta factory hammer 8. Standard carry bevel of sharp edges 9. Deburr pistol internally 10. Tune extractor & ejector 11. Recut barrel throat; polish feed ramp 12. Titanium firing pin with heavy duty firing pin spring 13. 4.5 lb. trigger job 14. Front cocking serrations (Additional $100 charge) 15. Refinish as needed. (Additional charge for some finishes) 16. Inspect & test fire for function
1911-A1 TRP Package GI & Mil Spec models: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $1645.00 Older Springfield models (pre 2000): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $1450.00 “Loaded Springfield models” (2000 & newer): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $ 895.00 1. Install TRP barrel & bushing (bull barrel system in pistols shorter than 5”) 2. Factory skeletonized delta hammer 3. Low mount Novak style rear sight with tritium inserts 4. Dovetail front sight with tritium dot insert (Dovetail & tritium insert not available on ported V10 handguns) 5. Extended ambidextrous thumb safety 6. Beavertail grip safety 7. Adjustable lightweight aluminum trigger 8. Full length guide rod with heavy duty recoil spring 9. Flat checkered mainspring housing 10. Polished feed ramp; throated barrel 11. Tune & polish extractor 12. Deburr pistol internally 13. Standard carry bevel sharp edges of pistol 14. Machine checker front strap, 20LPI 15. Tune trigger pull to 4.5 lb 16. Front cocking serrations (Optional - no price reduction if not done) 17. Refinish as needed (carbon steel pistols-Armory Kote™; stainless steel-satin finish) 18. G10 black/gray grips 19. Springfield 2 piece mag well-Additional $100 charge 20. **No TRP markings added to pistol in this package.** 21. Inspect & test fire for function 22. Stainless steel 1911-A1 pistols may require an additional fee, determined upon inspection 1911-A1 Tech Inspection:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $100.00 Have your 1911-A1 pistol checked by a custom technician for safe function. Replacement of parts at additional charge. (Customer will be contacted with additional charges, if any, after inspection.) This does not include any reliability tuning. 1911-A1 Sights: (*Refinishing done at additional charge.) Fixed Sight Options: ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ Install fixed 3 white dot Mil Spec sights in existing sight cuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Install Novak or similar style low mount rear target fixed sight, matching front sight. . . . . . . . . . . . . . . . . . Install Heinie low mount rear target sight, matching front sight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Install Novak style low mount fixed rear sight , matching front sight, with tritium inserts. . . . . . . . . . . . . . Install Heine low mount fixed sights with tritium inserts (specify style) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Install tritium night sights (slide already milled with correct front & rear sight cuts) . . . . . . . . . . . . . . . . . . . Install tritium night sights in existing low mount rear sight cut, new dovetail front cut . . . . . . . . . . . . . . . . Install Harrison Design fixed sights, in existing LPA or Bomar style sight cuts in slide, (front & rear sight set) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Same as above, but with tritium inserts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Install fixed rear sight only in existing (Novak Style or Loaded Style) rear sight cut . . . . . . . . . . . . . . . . . . . . . Install fixed Trijicon HD night sights (Slide already milled w/correct front & rear sight cuts). . . . . . . . . . . . $ 65.00 $180.00* $180.00* $260.00* $260.00* $150.00 $165.00 $100.00 $150.00 $80.00 $175.00
Adjustable Rear Sight Options: ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ Install Springfield fully adjustable target rear sight, low mount cut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Install Springfield fully adjustable target rear sight, deluxe cut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Install Springfield fully adjustable target rear sight, forward protected cut . . . . . . . . . . . . . . . . . . . . . . . . . . . . Install Springfield fully adjustable rear sight, matching dovetail front (with 3 dot tritium inserts) . . . . . . Install Springfield fully adjustable rear sight, matching dovetail front with 3 dot tritium inserts (slide milled with correct sight cuts) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Install adjustable carry sights with tritium inserts (includes front & rear sight) . . . . . . . . . . . . . . . . . . . . . . . . . Install adjustable carry sights with tritium inserts (slide already milled with correct sight cuts) . . . . . . . . . Install low mount Aristocrat tri-set sight set or Aristocrat rib . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $175.00* $200.00* $200.00* $350.00 $175.00 $350.00* $175.00 $300.00*
Front Sight Options: ❑ ❑ ❑ ❑ ❑ ❑ ❑ Install dovetail target front sight, any style, includes cold bluing of sight cut . . . . . . . . . . . . . . . . . . . . . . . . . . Install dovetail front sight with fiber optic insert, includes cold bluing of sight cut . . . . . . . . . . . . . . . . . . . . Install dovetail front sight with tritium insert, includes cold bluing for sight cut. . . . . . . . . . . . . . . . . . . . . . . Install dovetail front sight with gold bead insert, includes cold bluing of sight cut . . . . . . . . . . . . . . . . . . . . Install dovetail front sight with fiber optic insert, in existing dovetail cut in slide. . . . . . . . . . . . . . . . . . . . . . Install dovetail front sight with tritium insert, in existing dovetail cut in slide . . . . . . . . . . . . . . . . . . . . . . . . . . Install dovetail front sight with gold bead, in existing dovetail cut in slide . . . . . . . . . . . . . . . . . . . . . . . . . . . . $ 55.00 $ 80.00 $ 90.00 $95.00 $ 65.00 $ 75.00 $80.00
Misc. Sight Options: ❑ Modify sights for 3 painted white dots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $ 65.00 ❑ Ransom rest at 50 yards for accuracy. Match Grade Pistols only. (test target enclosed when pistol returned) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $100.00 **Target sights are plain black and do not have any type of dots or inserts. Fiber optic sights require some sort of ambient light source to glow and will not glow in low light or darkness. Tritium inserts will only glow in very low light or darkness.** 1911-A1 Barrels & Accuracy: ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ Fit slide to frame (tighten); reparkerizing as necessary. Other finishes additional charge. . . . . . . . . . . . . . . Acc-U-Rail slide rail system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fit match barrel & bushing (non-supported chamber) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fit match bull barrel (non-supported chamber) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fit fully ramped & supported match barrel (specify barrel & bushing or bull barrel) . . . . . . . . . . . . . . . . . . . . Fit match bushing only to existing barrel & slide (5” or longer barrel length) . . . . . . . . . . . . . . . . . . . . . . . . . . Fit custom compensator & match barrel (non-supported chamber, cone or bushing style) . . . . . . . . . . . . Fit custom compensator & match barrel (ramped & supported chamber, cone or bushing style) . . . . . . . 11 degree crown on bbl and flush cut. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $190.00 $295.00 $290.00 $350.00 $390.00 $ 60.00 $675.00 $825.00 $65.00
Triggers; Trigger Work; Hammer: ❑ ❑ ❑ ❑ ❑ Fit factory skeletonized hammer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fit match trigger (Specify speed, long match, short match) No adjustment of trigger pull . . . . . . . . . . . . . Action job, series 70 pistols (4 lb. pull or greater) with existing parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Action job, series 80 pistols (4 lb. pull or greater) with existing parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Action job with tool steel match hammer & sear (Required for trigger pull less than 4 lb.) . . . . . . . . . . . . . $ 50.00 $ 50.00 $100.00 $125.00 $225.00
Safeties; Mag Releases; Mag Wells (*Refinishing done at additional charge.) ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ Fit extended ambidextrous thumb safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fit extended single side thumb safety (not ambidextrous) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fit Springfield beavertail grip safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fit extended magazine release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fit flat checkered mainspring housing (Specify ILS or non-ILS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bevel & polish magazine well on frame. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fit S&A 1 piece magazine well to match bevel on frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fit S&A 1 piece magazine well to match bevel on frame with concealment bevel . . . . . . . . . . . . . . . . . . . . . . Fit weld-on magazine well, opened to maximum diameter (Includes new mainspring housing) . . . . . . . Install Heinie magazine well . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Add lanyard loop to existing mainspring housing (Specify standard or recessed) . . . . . . . . . . . . . . . . . . . . . . $100.00 $ 80.00 $100.00* $ 40.00 $ 75.00 $ 55.00* $180.00* $215.00* $275.00* $275.00 $ 75.00*
Internal Tuning: ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ Tune extractor (labor only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fit & tune new extractor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Polish feed ramp & throat barrel (labor only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Deburr pistol internally (labor only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bevel & polish magazine well (labor only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Install full length guide rod (Specify 1 or 2 piece) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Install tungsten guide rod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Install extended ejector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Install GI guide rod system (Plug & guide rod only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $ 30.00 $ 65.00 $ 50.00 $ 50.00* $ 50.00* $ 50.00 $ 85.00 $ 35.00 $ 25.00
External Modifications: (*Refinishing required at additional charge.) Front Strap Treatments: (Send picture for price quote if possible) ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ Hand checker front strap, 20LPI (single stack models). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hand checker front strap, 25LPI (single stack models). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hand checker front strap, 30LPI (single stack models). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Machine checker front strap, 20LPI (single stack models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Machine checker front strap, 25LPI (single stack models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Machine checker front strap, 30LPI (single stack models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hand checker front strap, 20LPI (Springfield wide body frame). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Serrate front strap. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stipple front strap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stipple front strap of Springfield wide body frame (Stipple each side of serrated front strap) . . . . . . . . . . Other front strap treatments available upon request . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $200.00* $220.00* $250.00* $150.00* $160.00* $170.00* $275.00* $110.00* $135.00* $175.00* P.O.R.*
Other Frame Modifications: ❑ ❑ ❑ ❑ ❑ ❑ ❑ Checker underneath trigger guard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Checker front of trigger guard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Square style trigger guard (Specify standard or moved forward 3/8”). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Undercut front strap (Specify style) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Recontour front strap & dust cover for 2002 specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Modify frame for “Bobtail style” mainspring housing (Mainspring housing included) Full size frame only . Round butt of frame and mainspring housing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $ 70.00* $ 95.00* $250.00* $ 75.00* $145.00* $225.00* $ 65.00*
Slide Modifications: ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ Checker rear of slide (Specify 30LPI, 40LPI, or 50LPI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Serrate rear of slide, 40LPI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Serrate top of slide, 40LPI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Flatten top of slide & serrate 40LPI (Not available on slides with dovetail front sight). . . . . . . . . . . . . . . . . . Machine slide & barrel for ports (Requires bull barrel installation at additional charge). . . . . . . . . . . . . . . . Front cocking serrations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Skeletonize slide for light loads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Lower & flare ejection port (Includes properly fit extended ejector) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ball cuts on slide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . French border top of slide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Lightening cuts in slide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Carry cuts on front of slide (Removes front cocking serrations). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $ 90.00* $ 75.00* $110.00* $160.00* $250.00* $100.00* $190.00* $ 90.00* $ 80.00* $100.00* P.O.R $ 65.00*
Other External Modifications: ❑ ❑ ❑ ❑ ❑ Standard carry bevel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Radical carry bevel (“Soap bar” feel) (Carbon steel handguns) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Radical carry bevel (“Soap bar” feel) (Stainless steel handguns) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Nub slide stop (FBI style) using existing slide stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Drill & tap for scope mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $100.00* $350.00* $450.00 $25.00 P.O.R.
Refinishing Services: (Some finishes may require additional shipping and handling charges.) Refinishing charges include minimal prep time. Firearms that require extensive prep work, or are deeply pitted, may require a labor fee. We will notify you of any additional fees before starting the finish work on the handgun. ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ Parkerize complete pistol. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Parkerize slide & slide small parts only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Parkerize frame & frame small parts only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Parkerize small parts only. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Blue complete pistol (Specify style-matte, brushed, high polish. Addl. charge for high polish.). . . . . . . . Blue slide & slide small parts only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Blue frame & frame small parts only. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Blue small parts only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Armory Kote™ complete pistol (Specify Flat Black, Satin Black, or OD Green). . . . . . . . . . . . . . . . . . . . . . . . . . Armory Kote™ slide and slide small parts only (Specify Flat Black, Satin Black, or OD Green) . . . . . . . . . . . Armory Kote™ frame & frame small parts only (Specify Flat Black, Satin Black, or OD Green) . . . . . . . . . . . Armory Kote™ small parts only (Specify Flat Black, Satin Black, or OD Green) . . . . . . . . . . . . . . . . . . . . . . . . . . Black T finish complete pistol (Matte black or OD Green). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Black T finish slide & slide small parts only (Matte black or OD Green) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Black T finish frame & frame small parts only (Matte black or OD Green) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Black T small parts only (Matte black or OD Green) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Nickel Teflon complete pistol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Nickel Teflon slide & slide small parts only. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Nickel Teflon frame & frame small parts only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Nickel Teflon small parts only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hard chrome complete pistol (Matte or brushed. Addl. charge for brushed.) . . . . . . . . . . . . . . . . . . . . . . . . . . Hard chrome slide & slide small parts only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hard chrome frame & frame small parts only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hard chrome small parts only. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Strip chrome from complete pistol. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Strip chrome from slide & slide small parts only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Strip chrome from frame & frame small parts only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $80.00 $45.00 $45.00 P.O.R. $250.00 $125.00 $175.00 P.O.R. $150.00 $ 80.00 $ 80.00 P.O.R. $215.00 $100.00 $145.00 P.O.R. $265.00 $165.00 $190.00 P.O.R. $265.00 $165.00 $190.00 P.O.R. $ 75.00 $ 40.00 $ 40.00
Refinishing Continued on Next Page
❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑
Strip chrome from small parts only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $ 40.00 Anodize lightweight frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $175.00 Satin (matte) finish stainless steel pistol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P.O.R. Xtremeflauge complete pistol (Custom patterns available.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Beg. $265.00 Xtremeflauge slide & slide small parts only (Custom patterns available) . . . . . . . . . . . . . . . . . . . . . . . . . . Beg. $150.00 Xtremeflauge frame & frame small parts only (Custom patterns available). . . . . . . . . . . . . . . . . . . . . . . Beg. $165.00 Ion Bond complete pistol. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $395.00 Ion Bond slide & slide small parts only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $195.00 Ion Bond frame & frame small parts only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $195.00
*Requires refinishing at additional charge. See Refinishing list for additional cost. Parts included in above services, unless otherwise stated. Customer supplied parts must be inspected by Springfield gunsmiths before they can be used in custom build projects, and may require additional charges for fitting and installation. Springfield Custom™ will accept and install new customer supplied parts which meet our quality standard. Cost for installation of these parts may be as much as, or more, than a similar Springfield part on our price list. Please note, Springfield Inc.’s limited lifetime warranty does not apply to customer supplied parts. Any claim for warranty on these parts must be addressed through the part’s manufacturer or place of purchase. Hard chrome and Ionbond finish are not available for lightweight aluminum frames. Prices subject to change without notice. P.O.R. - Price on Request Each pistol sent to the Springfield Custom Shop must be received with a detailed list (or custom worksheet) of the work to be performed. Any pistol received in the custom shop without a list of requested work, or a return merchandise authorization (RMA) number, will be returned. If you are unsure what work you want done, call or email our office PRIOR to shipping.
Custom Gun Work Terms 1. We will work on any quality 1911-A1 style, XD®, or XD(M)™ pistol. We reserve the right to refuse to work on any pistol determined to be of inferior quality or made unserviceable by any work performed by another person. 2. We use your pistol as collateral while the custom work is being completed; so no deposit is required. 3. Parts installed will match the finish of the handgun unless otherwise specified by the customer. 4. Please SEND any magazine(s) that will be used in the handgun. Please REMOVE all items not necessary for the custom work; for example, gun rugs, bushing wrenches, etc. 5. Your pistol will be test fired for function with quality factory loaded ammunition upon completion of the work. If you have a specific ammunition type you wish to be tested, please contact our office for instructions. 6. We recommend shipping to Springfield Custom by an insured shipper, such as UPS or Fed Ex. Ship to: Springfield Custom, 420 West Main St., Geneseo, IL 61254. Your custom work will not be scheduled until we have received the firearm and a signed work order form. Ask for details on our round trip shipping package through Fed Ex to get your handgun to our shop for work. 7. Payment may be made by Visa, MasterCard, Discover, American Express, cashier’s check, money order, or personal check. (Custom work or complete pistols, which are paid by personal check, may be held up to 21 days before shipment of the firearm.) 8. All work order changes on complete pistols or upgrades will be assessed a charge of $25 per change and could delay completion and delivery of the handgun. All change requests, for custom work or complete custom pistols, must be submitted in writing and be signed and dated by the customer. (Emails to the [email protected] address will be accepted for changes with proper documentation in the email.) 9. Return shipping and handling charges are not included in Springfield Custom pricing. An additional charge to cover return shipping and handling will be added to the invoice when the work is completed. 10. Due to federal government regulations, customer’s firearms must be return shipped to the address from which they have been received. They can only be shipped to businesses, other than licensed firearms’ dealers, if the customer owns the business and that is clearly stated in the paperwork that accompanies the handgun to our shop. (If you have a change of home address during the time your pistol is in the shop, Springfield Custom must receive a written request with the new address, serial number of the pistol, return authorization number and customer’s signature.) 11. Estimated completion times are just estimates. Due to scheduling, work flow, and other events beyond our control, these estimates are subject to change. We will do our best to quote you a reasonable time frame for completion of your custom pistol or work. 12. If you do not see a custom service listed on the preceding pages, please contact our office with your request. Since we have a full in-house custom shop, we are able to do just about anything you can dream to your handgun, within reason. I have read, understand, and agree to the Custom Gun Work Terms, in the Springfield Custom Shop Price List. Having read and understood the above terms, I authorize Springfield Custom to perform the specified work on my handgun. Name:__________________________________________________________________________________________ Signature:_______________________________________________________________________________________ Address:________________________________________________________________________________________ City/State/Zip:____________________________________________________________________________________ 1st Daytime Phone Number:________________________________________________________________________ 2nd Daytime Phone Number:_______________________________________________________________________ Serial Number of Pistol:____________________________________________________________________________ Email Address:___________________________________________________________________________________ Credit Card Number:______________________________________________________________________________ Expiration Date/CID Security Number:________________________________________________________________
REGISTER FOR YOUR WARRANTY ON-LINE AT WWW.SPRINGFIELDARMORY.COM
PLEASE CONTACT THE DEPARTMENT OF JUSTICE IN YOUR AREA REGARDING SPECIFIC RESTRICTIONS IN YOUR STATE. SPECIFICATIONS AND PRICES ARE SUBJECT TO CHANGE WITHOUT NOTICE. PRODUCTS MAY VARY FROM THOSE DEPICTED IN PHOTOS. SPRINGFIELD ARMORY® RESERVES THE RIGHT TO END PROMOTIONAL PROGRAMS AT ANYTIME WITHOUT NOTICE. SOME ITEMS SHOWN WITH OPTIONAL ACCESSORIES. ©2013 SPRINGFIELD ARMORY®. NO PART OF THIS CATALOG MAY BE REPRODUCED WITHOUT THE WRITTEN CONSENT OF SPRINGFIELD ARMORY® VERSION 2013 - 1
LIMITED LIFETIME WARRANTY
WWW.SPRINGFIELDARMORY.COM 1-800-617-6751 420 WEST MAIN STREET GENESEO, IL 61254
1911-A1 TRP Package GI & Mil Spec models: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $1645.00 Older Springfield models (pre 2000): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $1450.00 “Loaded Springfield models” (2000 & newer): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $ 895.00 1. Install TRP barrel & bushing (bull barrel system in pistols shorter than 5”) 2. Factory skeletonized delta hammer 3. Low mount Novak style rear sight with tritium inserts 4. Dovetail front sight with tritium dot insert (Dovetail & tritium insert not available on ported V10 handguns) 5. Extended ambidextrous thumb safety 6. Beavertail grip safety 7. Adjustable lightweight aluminum trigger 8. Full length guide rod with heavy duty recoil spring 9. Flat checkered mainspring housing 10. Polished feed ramp; throated barrel 11. Tune & polish extractor 12. Deburr pistol internally 13. Standard carry bevel sharp edges of pistol 14. Machine checker front strap, 20LPI 15. Tune trigger pull to 4.5 lb 16. Front cocking serrations (Optional - no price reduction if not done) 17. Refinish as needed (carbon steel pistols-Armory Kote™; stainless steel-satin finish) 18. G10 black/gray grips 19. Springfield 2 piece mag well-Additional $100 charge 20. **No TRP markings added to pistol in this package.** 21. Inspect & test fire for function 22. Stainless steel 1911-A1 pistols may require an additional fee, determined upon inspection 1911-A1 Tech Inspection:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $100.00 Have your 1911-A1 pistol checked by a custom technician for safe function. Replacement of parts at additional charge. (Customer will be contacted with additional charges, if any, after inspection.) This does not include any reliability tuning. 1911-A1 Sights: (*Refinishing done at additional charge.) Fixed Sight Options: ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ Install fixed 3 white dot Mil Spec sights in existing sight cuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Install Novak or similar style low mount rear target fixed sight, matching front sight. . . . . . . . . . . . . . . . . . Install Heinie low mount rear target sight, matching front sight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Install Novak style low mount fixed rear sight , matching front sight, with tritium inserts. . . . . . . . . . . . . . Install Heine low mount fixed sights with tritium inserts (specify style) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Install tritium night sights (slide already milled with correct front & rear sight cuts) . . . . . . . . . . . . . . . . . . . Install tritium night sights in existing low mount rear sight cut, new dovetail front cut . . . . . . . . . . . . . . . . Install Harrison Design fixed sights, in existing LPA or Bomar style sight cuts in slide, (front & rear sight set) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Same as above, but with tritium inserts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Install fixed rear sight only in existing (Novak Style or Loaded Style) rear sight cut . . . . . . . . . . . . . . . . . . . . . Install fixed Trijicon HD night sights (Slide already milled w/correct front & rear sight cuts). . . . . . . . . . . . $ 65.00 $180.00* $180.00* $260.00* $260.00* $150.00 $165.00 $100.00 $150.00 $80.00 $175.00
Adjustable Rear Sight Options: ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ Install Springfield fully adjustable target rear sight, low mount cut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Install Springfield fully adjustable target rear sight, deluxe cut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Install Springfield fully adjustable target rear sight, forward protected cut . . . . . . . . . . . . . . . . . . . . . . . . . . . . Install Springfield fully adjustable rear sight, matching dovetail front (with 3 dot tritium inserts) . . . . . . Install Springfield fully adjustable rear sight, matching dovetail front with 3 dot tritium inserts (slide milled with correct sight cuts) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Install adjustable carry sights with tritium inserts (includes front & rear sight) . . . . . . . . . . . . . . . . . . . . . . . . . Install adjustable carry sights with tritium inserts (slide already milled with correct sight cuts) . . . . . . . . . Install low mount Aristocrat tri-set sight set or Aristocrat rib . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $175.00* $200.00* $200.00* $350.00 $175.00 $350.00* $175.00 $300.00*
Front Sight Options: ❑ ❑ ❑ ❑ ❑ ❑ ❑ Install dovetail target front sight, any style, includes cold bluing of sight cut . . . . . . . . . . . . . . . . . . . . . . . . . . Install dovetail front sight with fiber optic insert, includes cold bluing of sight cut . . . . . . . . . . . . . . . . . . . . Install dovetail front sight with tritium insert, includes cold bluing for sight cut. . . . . . . . . . . . . . . . . . . . . . . Install dovetail front sight with gold bead insert, includes cold bluing of sight cut . . . . . . . . . . . . . . . . . . . . Install dovetail front sight with fiber optic insert, in existing dovetail cut in slide. . . . . . . . . . . . . . . . . . . . . . Install dovetail front sight with tritium insert, in existing dovetail cut in slide . . . . . . . . . . . . . . . . . . . . . . . . . . Install dovetail front sight with gold bead, in existing dovetail cut in slide . . . . . . . . . . . . . . . . . . . . . . . . . . . . $ 55.00 $ 80.00 $ 90.00 $95.00 $ 65.00 $ 75.00 $80.00
Misc. Sight Options: ❑ Modify sights for 3 painted white dots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $ 65.00 ❑ Ransom rest at 50 yards for accuracy. Match Grade Pistols only. (test target enclosed when pistol returned) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $100.00 **Target sights are plain black and do not have any type of dots or inserts. Fiber optic sights require some sort of ambient light source to glow and will not glow in low light or darkness. Tritium inserts will only glow in very low light or darkness.** 1911-A1 Barrels & Accuracy: ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ Fit slide to frame (tighten); reparkerizing as necessary. Other finishes additional charge. . . . . . . . . . . . . . . Acc-U-Rail slide rail system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fit match barrel & bushing (non-supported chamber) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fit match bull barrel (non-supported chamber) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fit fully ramped & supported match barrel (specify barrel & bushing or bull barrel) . . . . . . . . . . . . . . . . . . . . Fit match bushing only to existing barrel & slide (5” or longer barrel length) . . . . . . . . . . . . . . . . . . . . . . . . . . Fit custom compensator & match barrel (non-supported chamber, cone or bushing style) . . . . . . . . . . . . Fit custom compensator & match barrel (ramped & supported chamber, cone or bushing style) . . . . . . . 11 degree crown on bbl and flush cut. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $190.00 $295.00 $290.00 $350.00 $390.00 $ 60.00 $675.00 $825.00 $65.00
Triggers; Trigger Work; Hammer: ❑ ❑ ❑ ❑ ❑ Fit factory skeletonized hammer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fit match trigger (Specify speed, long match, short match) No adjustment of trigger pull . . . . . . . . . . . . . Action job, series 70 pistols (4 lb. pull or greater) with existing parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Action job, series 80 pistols (4 lb. pull or greater) with existing parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Action job with tool steel match hammer & sear (Required for trigger pull less than 4 lb.) . . . . . . . . . . . . . $ 50.00 $ 50.00 $100.00 $125.00 $225.00
Safeties; Mag Releases; Mag Wells (*Refinishing done at additional charge.) ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ Fit extended ambidextrous thumb safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fit extended single side thumb safety (not ambidextrous) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fit Springfield beavertail grip safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fit extended magazine release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fit flat checkered mainspring housing (Specify ILS or non-ILS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bevel & polish magazine well on frame. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fit S&A 1 piece magazine well to match bevel on frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fit S&A 1 piece magazine well to match bevel on frame with concealment bevel . . . . . . . . . . . . . . . . . . . . . . Fit weld-on magazine well, opened to maximum diameter (Includes new mainspring housing) . . . . . . . Install Heinie magazine well . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Add lanyard loop to existing mainspring housing (Specify standard or recessed) . . . . . . . . . . . . . . . . . . . . . . $100.00 $ 80.00 $100.00* $ 40.00 $ 75.00 $ 55.00* $180.00* $215.00* $275.00* $275.00 $ 75.00*
Internal Tuning: ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ Tune extractor (labor only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fit & tune new extractor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Polish feed ramp & throat barrel (labor only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Deburr pistol internally (labor only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bevel & polish magazine well (labor only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Install full length guide rod (Specify 1 or 2 piece) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Install tungsten guide rod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Install extended ejector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Install GI guide rod system (Plug & guide rod only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $ 30.00 $ 65.00 $ 50.00 $ 50.00* $ 50.00* $ 50.00 $ 85.00 $ 35.00 $ 25.00
External Modifications: (*Refinishing required at additional charge.) Front Strap Treatments: (Send picture for price quote if possible) ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ Hand checker front strap, 20LPI (single stack models). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hand checker front strap, 25LPI (single stack models). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hand checker front strap, 30LPI (single stack models). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Machine checker front strap, 20LPI (single stack models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Machine checker front strap, 25LPI (single stack models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Machine checker front strap, 30LPI (single stack models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hand checker front strap, 20LPI (Springfield wide body frame). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Serrate front strap. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stipple front strap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stipple front strap of Springfield wide body frame (Stipple each side of serrated front strap) . . . . . . . . . . Other front strap treatments available upon request . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $200.00* $220.00* $250.00* $150.00* $160.00* $170.00* $275.00* $110.00* $135.00* $175.00* P.O.R.*
Other Frame Modifications: ❑ ❑ ❑ ❑ ❑ ❑ ❑ Checker underneath trigger guard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Checker front of trigger guard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Square style trigger guard (Specify standard or moved forward 3/8”). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Undercut front strap (Specify style) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Recontour front strap & dust cover for 2002 specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Modify frame for “Bobtail style” mainspring housing (Mainspring housing included) Full size frame only . Round butt of frame and mainspring housing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $ 70.00* $ 95.00* $250.00* $ 75.00* $145.00* $225.00* $ 65.00*
Slide Modifications: ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ Checker rear of slide (Specify 30LPI, 40LPI, or 50LPI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Serrate rear of slide, 40LPI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Serrate top of slide, 40LPI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Flatten top of slide & serrate 40LPI (Not available on slides with dovetail front sight). . . . . . . . . . . . . . . . . . Machine slide & barrel for ports (Requires bull barrel installation at additional charge). . . . . . . . . . . . . . . . Front cocking serrations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Skeletonize slide for light loads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Lower & flare ejection port (Includes properly fit extended ejector) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ball cuts on slide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . French border top of slide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Lightening cuts in slide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Carry cuts on front of slide (Removes front cocking serrations). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $ 90.00* $ 75.00* $110.00* $160.00* $250.00* $100.00* $190.00* $ 90.00* $ 80.00* $100.00* P.O.R $ 65.00*
Other External Modifications: ❑ ❑ ❑ ❑ ❑ Standard carry bevel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Radical carry bevel (“Soap bar” feel) (Carbon steel handguns) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Radical carry bevel (“Soap bar” feel) (Stainless steel handguns) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Nub slide stop (FBI style) using existing slide stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Drill & tap for scope mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $100.00* $350.00* $450.00 $25.00 P.O.R.
Refinishing Services: (Some finishes may require additional shipping and handling charges.) Refinishing charges include minimal prep time. Firearms that require extensive prep work, or are deeply pitted, may require a labor fee. We will notify you of any additional fees before starting the finish work on the handgun. ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ Parkerize complete pistol. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Parkerize slide & slide small parts only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Parkerize frame & frame small parts only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Parkerize small parts only. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Blue complete pistol (Specify style-matte, brushed, high polish. Addl. charge for high polish.). . . . . . . . Blue slide & slide small parts only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Blue frame & frame small parts only. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Blue small parts only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Armory Kote™ complete pistol (Specify Flat Black, Satin Black, or OD Green). . . . . . . . . . . . . . . . . . . . . . . . . . Armory Kote™ slide and slide small parts only (Specify Flat Black, Satin Black, or OD Green) . . . . . . . . . . . Armory Kote™ frame & frame small parts only (Specify Flat Black, Satin Black, or OD Green) . . . . . . . . . . . Armory Kote™ small parts only (Specify Flat Black, Satin Black, or OD Green) . . . . . . . . . . . . . . . . . . . . . . . . . . Black T finish complete pistol (Matte black or OD Green). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Black T finish slide & slide small parts only (Matte black or OD Green) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Black T finish frame & frame small parts only (Matte black or OD Green) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Black T small parts only (Matte black or OD Green) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Nickel Teflon complete pistol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Nickel Teflon slide & slide small parts only. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Nickel Teflon frame & frame small parts only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Nickel Teflon small parts only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hard chrome complete pistol (Matte or brushed. Addl. charge for brushed.) . . . . . . . . . . . . . . . . . . . . . . . . . . Hard chrome slide & slide small parts only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hard chrome frame & frame small parts only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hard chrome small parts only. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Strip chrome from complete pistol. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Strip chrome from slide & slide small parts only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Strip chrome from frame & frame small parts only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $80.00 $45.00 $45.00 P.O.R. $250.00 $125.00 $175.00 P.O.R. $150.00 $ 80.00 $ 80.00 P.O.R. $215.00 $100.00 $145.00 P.O.R. $265.00 $165.00 $190.00 P.O.R. $265.00 $165.00 $190.00 P.O.R. $ 75.00 $ 40.00 $ 40.00
Refinishing Continued on Next Page
❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑
Strip chrome from small parts only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $ 40.00 Anodize lightweight frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $175.00 Satin (matte) finish stainless steel pistol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P.O.R. Xtremeflauge complete pistol (Custom patterns available.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Beg. $265.00 Xtremeflauge slide & slide small parts only (Custom patterns available) . . . . . . . . . . . . . . . . . . . . . . . . . . Beg. $150.00 Xtremeflauge frame & frame small parts only (Custom patterns available). . . . . . . . . . . . . . . . . . . . . . . Beg. $165.00 Ion Bond complete pistol. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $395.00 Ion Bond slide & slide small parts only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $195.00 Ion Bond frame & frame small parts only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $195.00
*Requires refinishing at additional charge. See Refinishing list for additional cost. Parts included in above services, unless otherwise stated. Customer supplied parts must be inspected by Springfield gunsmiths before they can be used in custom build projects, and may require additional charges for fitting and installation. Springfield Custom™ will accept and install new customer supplied parts which meet our quality standard. Cost for installation of these parts may be as much as, or more, than a similar Springfield part on our price list. Please note, Springfield Inc.’s limited lifetime warranty does not apply to customer supplied parts. Any claim for warranty on these parts must be addressed through the part’s manufacturer or place of purchase. Hard chrome and Ionbond finish are not available for lightweight aluminum frames. Prices subject to change without notice. P.O.R. - Price on Request Each pistol sent to the Springfield Custom Shop must be received with a detailed list (or custom worksheet) of the work to be performed. Any pistol received in the custom shop without a list of requested work, or a return merchandise authorization (RMA) number, will be returned. If you are unsure what work you want done, call or email our office PRIOR to shipping.
Custom Gun Work Terms 1. We will work on any quality 1911-A1 style, XD®, or XD(M)™ pistol. We reserve the right to refuse to work on any pistol determined to be of inferior quality or made unserviceable by any work performed by another person. 2. We use your pistol as collateral while the custom work is being completed; so no deposit is required. 3. Parts installed will match the finish of the handgun unless otherwise specified by the customer. 4. Please SEND any magazine(s) that will be used in the handgun. Please REMOVE all items not necessary for the custom work; for example, gun rugs, bushing wrenches, etc. 5. Your pistol will be test fired for function with quality factory loaded ammunition upon completion of the work. If you have a specific ammunition type you wish to be tested, please contact our office for instructions. 6. We recommend shipping to Springfield Custom by an insured shipper, such as UPS or Fed Ex. Ship to: Springfield Custom, 420 West Main St., Geneseo, IL 61254. Your custom work will not be scheduled until we have received the firearm and a signed work order form. Ask for details on our round trip shipping package through Fed Ex to get your handgun to our shop for work. 7. Payment may be made by Visa, MasterCard, Discover, American Express, cashier’s check, money order, or personal check. (Custom work or complete pistols, which are paid by personal check, may be held up to 21 days before shipment of the firearm.) 8. All work order changes on complete pistols or upgrades will be assessed a charge of $25 per change and could delay completion and delivery of the handgun. All change requests, for custom work or complete custom pistols, must be submitted in writing and be signed and dated by the customer. (Emails to the [email protected] address will be accepted for changes with proper documentation in the email.) 9. Return shipping and handling charges are not included in Springfield Custom pricing. An additional charge to cover return shipping and handling will be added to the invoice when the work is completed. 10. Due to federal government regulations, customer’s firearms must be return shipped to the address from which they have been received. They can only be shipped to businesses, other than licensed firearms’ dealers, if the customer owns the business and that is clearly stated in the paperwork that accompanies the handgun to our shop. (If you have a change of home address during the time your pistol is in the shop, Springfield Custom must receive a written request with the new address, serial number of the pistol, return authorization number and customer’s signature.) 11. Estimated completion times are just estimates. Due to scheduling, work flow, and other events beyond our control, these estimates are subject to change. We will do our best to quote you a reasonable time frame for completion of your custom pistol or work. 12. If you do not see a custom service listed on the preceding pages, please contact our office with your request. Since we have a full in-house custom shop, we are able to do just about anything you can dream to your handgun, within reason. I have read, understand, and agree to the Custom Gun Work Terms, in the Springfield Custom Shop Price List. Having read and understood the above terms, I authorize Springfield Custom to perform the specified work on my handgun. Name:__________________________________________________________________________________________ Signature:_______________________________________________________________________________________ Address:________________________________________________________________________________________ City/State/Zip:____________________________________________________________________________________ 1st Daytime Phone Number:________________________________________________________________________ 2nd Daytime Phone Number:_______________________________________________________________________ Serial Number of Pistol:____________________________________________________________________________ Email Address:___________________________________________________________________________________ Credit Card Number:______________________________________________________________________________ Expiration Date/CID Security Number:________________________________________________________________
REGISTER FOR YOUR WARRANTY ON-LINE AT WWW.SPRINGFIELDARMORY.COM
PLEASE CONTACT THE DEPARTMENT OF JUSTICE IN YOUR AREA REGARDING SPECIFIC RESTRICTIONS IN YOUR STATE. SPECIFICATIONS AND PRICES ARE SUBJECT TO CHANGE WITHOUT NOTICE. PRODUCTS MAY VARY FROM THOSE DEPICTED IN PHOTOS. SPRINGFIELD ARMORY® RESERVES THE RIGHT TO END PROMOTIONAL PROGRAMS AT ANYTIME WITHOUT NOTICE. SOME ITEMS SHOWN WITH OPTIONAL ACCESSORIES. ©2013 SPRINGFIELD ARMORY®. NO PART OF THIS CATALOG MAY BE REPRODUCED WITHOUT THE WRITTEN CONSENT OF SPRINGFIELD ARMORY® VERSION 2013 - 1
LIMITED LIFETIME WARRANTY
WWW.SPRINGFIELDARMORY.COM 1-800-617-6751 420 WEST MAIN STREET GENESEO, IL 61254
