ECET 365 Week 2 Quiz

Published on July 2017 | Categories: Education | Downloads: 139 | Comments: 0 | Views: 1422
Download PDF   Embed   Report

ECET 365 Week 2 Quiz Click Below Link To Purchase www.foxtutor.com/product/ecet-365-week-2-quiz 1. Question : (TCO #5) Identify the step size for an 8-bit analog-to-digital converter with Vref= 2.5 VDC? Student Answer: 10 millivolts 25 millivolts 4.9 millivolts 5 volts Comments: 2. Question : (TCO # 5) How many steps are available with a 10-bit ADC? Student Answer: 10 1024 512 256 Comments: 3. Question : (TCO #5) What is the cutoff frequency for a low-pass filter with a resistor R = 3000 and a capacitor C = .01 µf? Student Answer: f = 5.3 KHz f = 3300 Hz f = 120 KHz f = 6 KHz Comments: 4. Question : (TCO #5)A band-stop filter is a filter that _____ frequencies below low-limit and above high-limit frequencies and _____ frequencies between the limits. Student Answer: blocks; blocks passes; blocks blocks; passes has; blocks Comments: 5. Question : (TCO #5) A bridge with R1= 5.1 K, R2= 2 K, and R3= 15 K can be at null if R4is _____. Student Answer: 10.5 K 5.88 K 588 1 K Comments: 6. Question : (TCO #5) An instrumentation amplifier with two buffers has a feedback resistor of 100 K. The two resistors from the buffer's output to the input of the last stage OP-Amp are 1 K resistors. Voltage levels to the non-inverting buffer inputs. Voltage levels to the non-inverting buffer inputs are V1= .06 volt and V2= .02 volts. What is Voutof the instrumentation amplifier? Student Answer: 4 Volts 20.4 Volts 3.3 Volts 15.3 Volts Comments: 7. Question : (TCO #5) An embedded system with an 8-bit analog-to-digital converter is connected to a transducer with an output voltage of 10 millivolts. This signal is amplified by an amplifier with a gain of 25. Assume that this signal level is appropriate for the ADC input. If the reference voltage of the ADC converter is 5 volts, what will be the output of the ADC in binary form? Student Answer: 01100110 00110011 00001101 01111011 Comments: 8. Question : (TCO #5) An 8-bit analog-to-digital converter has maximum output voltage of 2.5 VDC. What is the reference voltage to this ADC? Student Answer: 2.5 VDC 5 VDC 1.25 VDC None of the above Comments: 9. Question : (TCO #5) A well-behaved analog signal with a frequency of 20 kHz is being sampled. What is the sampling frequency if frequency aliasing occurs? Student Answer: 90 kHz 40 kHz 85 kHz 60 khz Comments: 10. Question : (TCO #5) To model a nonlinear transducer, one can _____. Student Answer: use empirically determined nonlinear equation use a piecewise linear system use a lookup table located in memory All of the above

Comments

Content

ECET 365 Week 2 Quiz Click Below Link To Purchase www.foxtutor.com/product/ecet-365-week-2-quiz 1. Question : (TCO #5) Identify the step size for an 8-bit analog-to-digital converter with Vref= 2.5 VDC? Student Answer: 10 millivolts 25 millivolts 4.9 millivolts 5 volts Comments: 2. Question : (TCO # 5) How many steps are available with a 10-bit ADC? Student Answer: 10 1024 512 256 Comments: 3. Question : (TCO #5) What is the cutoff frequency for a low-pass filter with a resistor R = 3000 and a capacitor C = .01 µf? Student Answer: f = 5.3 KHz f = 3300 Hz f = 120 KHz f = 6 KHz Comments: 4. Question : (TCO #5)A band-stop filter is a filter that _____ frequencies below low-limit and above high-limit frequencies and _____ frequencies between the limits. Student Answer: blocks; blocks passes; blocks blocks; passes has; blocks Comments: 5. Question : (TCO #5) A bridge with R1= 5.1 K, R2= 2 K, and R3= 15 K can be at null if R4is _____. Student Answer: 10.5 K 5.88 K 588 1 K Comments: 6. Question : (TCO #5) An instrumentation amplifier with two buffers has a feedback resistor of 100 K. The two resistors from the buffer's output to the input of the last stage OP-Amp are 1 K resistors. Voltage levels to the non-inverting buffer inputs. Voltage levels to the non-inverting buffer inputs are V1= .06 volt and V2= .02 volts. What is Voutof the instrumentation amplifier? Student Answer: 4 Volts 20.4 Volts 3.3 Volts 15.3 Volts Comments: 7. Question : (TCO #5) An embedded system with an 8-bit analog-to-digital converter is connected to a transducer with an output voltage of 10 millivolts. This signal is amplified by an amplifier with a gain of 25. Assume that this signal level is appropriate for the ADC input. If the reference voltage of the ADC converter is 5 volts, what will be the output of the ADC in binary form? Student Answer: 01100110 00110011 00001101 01111011 Comments: 8. Question : (TCO #5) An 8-bit analog-to-digital converter has maximum output voltage of 2.5 VDC. What is the reference voltage to this ADC? Student Answer: 2.5 VDC 5 VDC 1.25 VDC None of the above Comments: 9. Question : (TCO #5) A well-behaved analog signal with a frequency of 20 kHz is being sampled. What is the sampling frequency if frequency aliasing occurs? Student Answer: 90 kHz 40 kHz 85 kHz 60 khz Comments: 10. Question : (TCO #5) To model a nonlinear transducer, one can _____. Student Answer: use empirically determined nonlinear equation use a piecewise linear system use a lookup table located in memory All of the above

Sponsor Documents

Or use your account on DocShare.tips

Hide

Forgot your password?

Or register your new account on DocShare.tips

Hide

Lost your password? Please enter your email address. You will receive a link to create a new password.

Back to log-in

Close