ECT 284 All Assignments
Comments
Content
ECT 284 Week 1 Homework
Click Below Link To Purchase
www.foxtutor.com/product/ect-284-week-1-homework
ECT 284 ECT/284 ECT 284 Week 1 Homework
ECT 284 Week 1 Lab Relay Pin-out Determination
Click Below Link To Purchase
www.foxtutor.com/product/ect-284-week-1-lab-relay-pin-out-determination
Relay Pin-out Determination
Objective
The objective of this lab exercise is to identify the pin-out of a typical electromechanical relay.
Parts Needed
1.Relay - 12V DC Coil, DPDT
2.Breadboard
3.Wire, wire cutter, and wire stripper
4.Variable Power supply
5.DMM
Related Tutorials
ECT 284 Week 2 Homework
Click Below Link To Purchase
www.foxtutor.com/product/ect-284-week-2-homework
Chapter 2, p. 49: Problems 1, 4, and 5
1. A discrete 120 V ac output module is to be used to control a 230 V dc solenoid valve. Draw a diagram showing how this could be accomplished using an interposing relay.
4. Create a typical five-digit address (according to Fig 2-4) for each of the following:
5. Assume the triac of an ac output module fails in the shorted state. How would this affect the device connected to this output?
ECT 284 Week 3 Homework
Click Below Link To Purchase
www.foxtutor.com/product/ect-284-week-3-homework
ECT 284 ECT/284 ECT 284 Week 3 Homework
ECT 284 Week 6 Homework
Click Below Link To Purchase
www.foxtutor.com/product/ect-284-week-6-homework
1. Give an example of an open-loop control system. Explain why the system is open-loop, and identify the controller and final control element.
• 2. Give an example of a closed-loop control system. Explain why the system is closed-loop, and identify the sensor, controller, and final control element
• 7. Describe the advantages of a 4- to 20-mA current loop as an input signal compared to a 0-to 5-V input signal
ECT 284 Week 6 iLab Garage Door Simulation
Click Below Link To Purchase
www.foxtutor.com/product/ect-284-week-6-ilab-garage-door-simulation
1.With reference to instructions given in step 5 complete the following:
2.Briefly describe the operation of each rung in the ladder logic program. Submit the worksheet and all attachments to week 6 dropbox.
ECT 284 Week 7 Question 1
Click Below Link To Purchase
www.foxtutor.com/product/ect-284-week-7-question-1
1.What NEMA (National Electrical Manufactures Association) enclosure is recommended for a PLC?
2. List advantages of mounting the PLC within an enclosure?
ECT 284 Week 7 Question 6
Click Below Link To Purchase
www.foxtutor.com/product/ect-284-week-7-question-6
4. Refer to module wiring diagram below for the following questions.
ECT 284 Week 3 Quiz
Click Below Link To Purchase
www.foxtutor.com/product/ect-284-week-3-quiz
2. (TCO 3) The status of I1, I2, and I3 is given in each of the following ladder logic programs. Check all correct statements.
3. (TCO 3) Based on the following ladder logic program (Remember, these are PLC instructions.), check all correct answers.
4. (TCO 3) Based on the following ladder logic program (Remember, these are PLC instructions.), check all correct answers.
6. (TCO 3) A ladder logic program and the associated physical input/output components are given below. Without depressing any push button and considering total darkness, which statement is true?
7. (TCO 3) A ladder logic program and the associated physical components are given below. The motor is running. The push button is not depressed. Check all correct answers
8. (TCO 3) Which Boolean expression represents the given logic circuit?
Sponsor Documents