Fingerprint Based Security System
Content
FingerPrint Based Security System
Personal Safes are revolutionary locking storage cases that open with just the touch of your finger. These products are designed as secure storage for medications, jewelry, weapons, documents, and other valuable or potentially harmful items.These utilize fingerprint recognition technology to allow access to only those whose fingerprints you choose. It contains all the necessary electronics to allow you to store, delete, and verify fingerprints with just the touch of a button. Stored fingerprints are retained even in the event of complete power failure or battery drain.These eliminates the need for keeping track of keys or remembering a combination password, or PIN. It can only be opened when an authorized user is present, since there are no keys or combinations to be copied or stolen, or locks that can be picked. In this project the fingerprint module from Miaxis Biometrics is used. It can store up to 750 finger prints on its own memory. It can be controlled through its serial port. The microcontroller AT89S52 interact with the module. You can Add a fingerprint, Delete a fingerprint and Identify the fingerprint. To add a fingerprint, just show the finger on the module and press the ADD key. Now the microcontroller will send the ADD command to the module and the module will add it into the memory. To delete the finger follow the same as above. To identify the finger, press the Identify button and if the finger matches then the Relay is complemented.Also the fingerprint ID is displayed over the LCD display. For more details about the Fingerprint module, please check the datasheet and you can get it from the datasheets page.
Sponsored Links: Password Based Door Locking (AT89C2051)
Security is a prime concern in our day-today life. Everyone wants to be as much secure as possible. An access control for doors forms a vital link in a security chain. The microcontroller based Door locker is an access control system that allows only authorized persons to access a restricted area. The system is fully controlled by the 8 bit microcontroller AT89C2051 which has a 2Kbytes of ROM for the program memory. The password is stored in the EPROM so that we can change it at any time. The system has a Keypad by which the password can be entered through it. When the entered password equals with the password stored in the memory then the relay gets on and so that the door is opened. If we entered a wrong password for more than three times then the Alarm is switched on. The default password is 1111 and you can change the password by dialing 1234, old password, new password #button. for example if you want to change the password from the default to 4523 then dial 123411114523# after dialing you can hear a beep sound which confirm the operation goes successful. There are two relays one to open the door and other to close the door. There is an button which should be placed inside the door so that the person inside can open/close the door. The passwords are stored on the
Personal Safes are revolutionary locking storage cases that open with just the touch of your finger. These products are designed as secure storage for medications, jewelry, weapons, documents, and other valuable or potentially harmful items.These utilize fingerprint recognition technology to allow access to only those whose fingerprints you choose. It contains all the necessary electronics to allow you to store, delete, and verify fingerprints with just the touch of a button. Stored fingerprints are retained even in the event of complete power failure or battery drain.These eliminates the need for keeping track of keys or remembering a combination password, or PIN. It can only be opened when an authorized user is present, since there are no keys or combinations to be copied or stolen, or locks that can be picked. In this project the fingerprint module from Miaxis Biometrics is used. It can store up to 750 finger prints on its own memory. It can be controlled through its serial port. The microcontroller AT89S52 interact with the module. You can Add a fingerprint, Delete a fingerprint and Identify the fingerprint. To add a fingerprint, just show the finger on the module and press the ADD key. Now the microcontroller will send the ADD command to the module and the module will add it into the memory. To delete the finger follow the same as above. To identify the finger, press the Identify button and if the finger matches then the Relay is complemented.Also the fingerprint ID is displayed over the LCD display. For more details about the Fingerprint module, please check the datasheet and you can get it from the datasheets page.
Sponsored Links: Password Based Door Locking (AT89C2051)
Security is a prime concern in our day-today life. Everyone wants to be as much secure as possible. An access control for doors forms a vital link in a security chain. The microcontroller based Door locker is an access control system that allows only authorized persons to access a restricted area. The system is fully controlled by the 8 bit microcontroller AT89C2051 which has a 2Kbytes of ROM for the program memory. The password is stored in the EPROM so that we can change it at any time. The system has a Keypad by which the password can be entered through it. When the entered password equals with the password stored in the memory then the relay gets on and so that the door is opened. If we entered a wrong password for more than three times then the Alarm is switched on. The default password is 1111 and you can change the password by dialing 1234, old password, new password #button. for example if you want to change the password from the default to 4523 then dial 123411114523# after dialing you can hear a beep sound which confirm the operation goes successful. There are two relays one to open the door and other to close the door. There is an button which should be placed inside the door so that the person inside can open/close the door. The passwords are stored on the
