Lap Ghep Xe Robot

Published on May 2016 | Categories: Documents | Downloads: 33 | Comments: 0 | Views: 171
of 13
Download PDF   Embed   Report

Comments

Content

http://www.ikalogic.com/tut_mech_1.php

Home Home

Articles and resources

Forums

Visitor contributions

Contact
Login

Username: Robot navigation

Password:

b Remember me c d e f g

Small Robot Drive Trains
By Ibrahim Kamal Last update: 4/4/08

Table of content:
Overview Traction and steering mechanisms Mounting the motors Transmitting power to the wheels Diameter of the wheels, speed and torque Mass distribution and robot stability Acquiring small motors and Building materials

Join the Mailing List Let us get in touch with you when we upload new interesting content. Name: Email: i Subscribe j k l m n
GO j Unsubscribe k l m n Get your Free Mailing List
by Bravenet.com

Overview
This Tutorial Aims to introduce to beginner the different techniques used to build the chassis and drive trains of relatively small robots.
What I mean by small robots, is the category of light weight robots where aspects like aerodynamics and vibration damping are not taken in account. Most of the fundamental theory remain the same for all sizes of robots, Theory such as robot stability, traction and steering techniques. However, This tutorial is dedicated to the construction of relatively small robots, explaining how to the implement your designs using material and equipment at the reach of any average level hobbyist.

1-Traction and steering mechanisms
There are many types of mechanisms that have been developed to move a robot from a place to another, more than you could imagine, however, we will only study some of those techniques which are the most adequate to relatively small robots: 1.1- Differential Drive system: This is the most common locomotion scheme in the world of robotics. It's easy to build, easy to control and can permit the robot to move in all required directions. In that system, two motors are connected, one to each of the two drive wheels at the right and at the left of the robot's base. Those two motors are responsible of driving the

robot back and forth as well as steering in any required direction. This system can even allow a robot to pivot in its place. The word "differential" comes from that this system relies on the difference between the two wheels the robot in the required path and move in any required curve. the fact velocity to drive make it

Figure 1A shows in a simplified way the principle of operation of differential drive. When the left and right motors are turning at the same speed, the robot moves forward or backward in a straight line. In order to turn right for example, the right motor is slowed down and the whole robot steers to the right. The bigger the difference of speed between the two wheels, the tighter will be the steering curve.

Figure 1.A: Differential drive system

As you can also notice in the figure 1.A, this system needs one or more caster wheels (also called free-wheels) to support the rest of the chassis while freely following the movement of the robot engaged by the two main drive wheels. Some robots use 2 caster wheels, adjacent to the drive wheels for better stability, but again, in the category of small robots, one caster wheel can be enough. Many roboticists even replace this single freewheel with a piece of bent metal or any other low friction surface to act as skid that slips on the ground under the action of the driving wheels. Figure 1B shows the chassis of one of our line follower robots where skids are used along with the drive wheels to support it

Figure 1.B: Skids used on a differential drive train

in a horizontal position. This technique becomes interesting when used for lightweight robots, where caster wheels can cause even more friction than the skids, and add additional and unnecessary weight to the robot. You can also notice in the figure 1B that the rear skid is not touching the ground, and thus is not a primary skid, but rather a secondary one just in case the robot pivots around the drive wheels to the back during a sudden acceleration for example. 1.2- Four wheel differential drive system:

Another variation of the differential drive system, is the 4 wheel differential drive system, which resembles the drive trains of tanks and bulldozers. As figure 1c shows, it consists of only two motors and 4 wheels. Each pair of wheels are mechanically connected together, usually by the mean of a belt forcing them to move together, driven by a single motor. The behavior of this drive train is similar to the previous differential drive system; If the the two motors turn at the same speed, the robot moves forward or backward, if there is a difference between the speed of the two motors, the robot will steer in the direction of the slower motor. This drive system implicates a great deal of friction, Figure 1.C: 4 wheel differential drive system specially during steering, and thus, to overcome this friction, it requires relatively powerful motors, as compared to the previous differential drive scheme. The advantage of this system is that it is very easy to build and is most suitable for running on low friction and dusty surfaces where other drive systems would suffer. 1.3- Car-type drive system: This drive system has many names, but calling it "car-type" make it clear to any reader, that it consists of 2 wheels coupled on the same axe at the back and one or two wheels capable of steering to control the displacement of the robot. While this technique is very difficult to implement mechanically, it provides two major advantages over other traction systems: Ease of control and accuracy (because traction and steering are connected to two independent motors). The best way to build your first 'car-type' drive train is to look at any old RC toy car. You can also use some parts of it's drive train to build your own, or even use the chassis of a brand-new RC toy car for your robot, as we did in the WFR project. Figure 1.D shows a simplified layout showing the principle of operation this drive system. Connecting the front (steering) wheels to the motor can be very complicated, but a basic rack and pinion arrangement can be enough for very low steering angles, otherwise, for relatively high steering angles, the rack and pinion arrangement will have to be enhanced with a sliding mechanism Figure 1.D: Basic car-type drive train allowing the green axe (in the figure) linking the two front wheels together to move freely along the axis of the chassis. There can be many other configurations based on the same idea, like a 2 wheel traction / 1 wheel steering drive train, which may be a little simpler to construct because the front wheel can be directly connected to a gearhead DC motor. 1.4- Divided chassis drive train: This is another locomotion scheme that we experienced, which has the advantage of being very powerful and highly configurable. Inneed, this system relies on 4 independent motors, each one coupled to one of the four wheels, allowing the robot to move forward or backward with the

accumulated power of four motors or to turn right and left with approximately equivalent power, but with minimum frictional losses. Figure 1.E shows how to implement such a configuration, and shows how the the chassis is divided into two parts, hinged together, allowing it to change it's shape to turn in tight curves. Usually, the two front motors are used only to drag the robot, while Figure 1.E: Picture and layout of the divided chassis the two rear motors are used either to push it or to bend the chassis (like a toy train) to turn right or left by running one of the two motors faster than the other. One last special feature of this system is that it has no head nor tail, in other words, there is no difference between the front part of the chassis and the rear one, making it possible for the robot to change it's direction, to adapt to any situation, without having to execute a 180 degrees rotation.

2-Mounting the Motors
When you are settled on a traction and steering mechanism for your robot, you have to find a way of fixing the motors firmly to the chassis. At this point, in order to construct a professional drive train, you have to take those points in consideration: You have to be able to mount and dismount the motor easily. Gluing, soldering and other permanent fixing solutions are not good ones. As a roboticist, building a prototype, You have to able the make any modifications easily. The outer shell of a motor is not designed to bear high, undistributed stresses. whatever the method you are using to mount and hold your motors in place, you have to increase the contact area between the motor's body and the mechanical part linking it to the chassis to prevent stress concentration and eventually damaging the motor. There are many items that you can buy at your nearest hardware store, to use it to mount the motor on the chassis, I present some ideas that I find to be the most adequate to this category of robots. 2.1- Pipe Clamps: Because they come in any size you want, because they are cheap, and because it can be used with any motor, this is my favorite choice. Initially, at the name implies, pipe clamps are used to fix water pipes on walls. Due to the resemblance of size and shape between the outer shell of a standard DC motor and water pipes, those clamps are very adequate to the job of holding motors firmly in place, while distributing any eventual stress along the whole contact surface. Figure 2.A shows a standard pipe clamp, where the right bolt was replaced with a longer 4mm screw, to be used later to fix the motor-clamp assembly to the chassis. Note

Figure 2.A: Pipe clamp

that there are many varieties of pipe clamps, so it's up to you to pay a visit to your hardware store and find the one that would be the most suitable according to your design. Most Pipe clamps come with a nut welded to it, allowing easier fixation to any adjacent plan (that plan can be a wall as it can be the chassis of your robot). Figure 2.B shows how a motor fits in that pipe clamp. Adding small parts of rubber between the surfaces of the motor and the clamp can be a good idea, as it will absorb any eventual vibration, and protect the motor's body. Figure 2.C shows how a pipe clamp can be used to mount the motor on the chassis. As you can notice, one of the main advantages of using a pipe clamp, is that you can easily adjust the distance between the motor and the base of the robot to which the motor is fixed, which is not the case with other solutions, like the U-Bolt idea..

Figure 2.B: DC motor & pipe clamp

Figure 2.C

2.2- U-bolts: If for any reason the pipe clamp solution cannot be used, this is the second best choice. I've never used this technique to fix motors, but i've seen it used by many hobbyists. The two reasons making this technique less effective that pipe clamps are: 1- The contact area is relatively small, thus stress concentration can be a problem. This problem can be Figure 2.D: U-Bolt solved by using more than one U-bolt for each motor. Picture from: http://www.gibsonstainless.com/ 2- The U-bolt is designed to hold a circular object by pushing it against a fixed surface. As figure 2.E shows, in our application, the circular object is the motor and the fixed surface is the chassis. so the height of the motor from the ground depends on the height of the part of the chassis where the motor is fixed. In contrast, with Pipe clamps, you can easily adjust the distance between the chassis and the motor.

Figure 2.E: U-Bolt on a motor

2.3- Building your own bracket: If your motor is too small, too big or just not adequate to any of the previous solutions, building your own bracket to hold your motor is not that difficult. You have to use your imagination, and cope with the components, tools and materials that are at your reach. At this point i'll only give you hints of materials you could use to easily attach your motors. - A rubber band (figure 2.F) can hold your motor in place exactly like a U-Bolt, while giving it some elasticity to absorb shocks and vibrations. You can obtain really strong rubber belts from old cassette players.

Figure 2.F

- Thick copper wire can also be used instead of the Ubolt, although it has the major disadvantage of being a permanent solution, any modification will be destructive and new wires will have to be installed. Figure 2.G shows actual pictures of DC motors that's I've mounted on one of my first robots.

Figure 2.G

- Plastic strap fastener, is still a permanent solution, but has the advantage of providing a strong attachment, while being easily introduced and fastened in small places where it would be harder to install copper wires or rubber bands.

Figure 2.H

- Metal sheets forming is the best alternative to U-Bolts and pipe clamps if you have the tools, skill, and material to do the job. Then you can form the exact required shape to firmly hold your motor in place. I personally recommend Aluminum as a working material. It's corrosion resistance, it's light weight and it's machinability, make it a perfect match for small robots.

3-Transmitting power to the wheels
There are many way of transmitting the power from the motor's shaft to the wheels, but in any case, friction is your biggest enemy. The frictional losses increase when the weight of the robot increases, specially if you're not using any ball bearings to support the shaft, which is usually the case in small robots. I am going to categorize the various techniques used for power transmission into two main categories: Direct transmission and Un direct transmission.

3.1 - Direct transmission
3.1.1- Direct transmission from a DC Motor, Which is when the wheels are directly mounted on the motor's shafts. This technique is only acceptable when working with very light weight robots, otherwise, those relatively small DC motors are not mechanically designed to bear any bending stresses that could be caused by directly mounting a wheel on it. Usually the internal bearing of those motors are designed to withstand the stresses required to keep a gear in place in a gearbox, or to withstand the tension in a rubber belt. In Most cases, directly mounting the output shaft of a DC motor to a wheel is rarely the best choice because without any speed reduction, the developed torque wont be enough to easily move a robot around. Figure 3.1.1 shows an example of how a small plastic wheel can be mounted to the tiny shaft of small motors. As you can see this is the same idea used in most toy cars, where parts are simply forced in their place. This is more interesting than more advanced shaft coupling techniques when you're working with tiny motors, because it would be very difficult to drill it's output shaft to install setscrews or pins. Figure 3.1.1

3.1.2- Direct transmission from a gearhead DC motor is the most common method used by roboticists, specially for the category of robot we are talking about. That's because the output

shaft from the gearbox of a gearhead motor are designed withstand higher stresses than the output shaft of the motor itself and has a very suitable output characteristics (low RPM and high toque). That can be noticed from the shape of the output shaft of a gearhead DC motor in the figures 3.1.2A and 3.1.2B, which is not fully circular to be able to firmly secure it to a shaft coupling or to a wheel in our case. There are many ways to fix a wheel to the output shaft of a gearhead DC motor, one of the simplest ways is to drill a hole in the body of the wheel, of the exact diameter of the screw to be used. Forcing the screw in the drilled material for the first time will form a helix mating the thread of your screw, allowing you to fasted the shaft in its place by simply driving the screw. If the wheel you are using doesn't have an extended shaft as shown in figure 3.1.2A, you will have to find another mean of fastening the motor's shaft to the wheel, but virtually any wheel you will find is designed to be mounted on a shaft, so using your imagination, you'll end up finding a solution to that problem, depending on the shape and size of the wheel. Figure 3.1.2B shows the output shaft of an old PITMAN GearHead DC motor.

Figure 3.1.2 A

Figure 3.1.2 B

3.2- Undirect transmission
Undirect transmission means that the shaft holding the wheels is on a totally different plane than the output shaft of the motor. Usually, between those two shaft is a reduction belt/gears arrangement. Undirect transmission is more suited to heavy robots, where rolling bearings are installed to support the shaft holding the wheels, to minimize any frictional losses due to the weight of the robot. Mechanically speaking, any wheel is to be fixed with rolling bearings, so this is the best method of all, but again, you have to remember that there are some compromises that can be made with small robots, to reduce cost, weight and complexity. Figure 3.2A shows a classic undirect transmission system, where the rotation of the motor's shaft is transmitted through a reduction pulley arrangement, lowering the RPM of the wheel, while increasing the torque. Notice how the the full weight of the robots is distributed only on the two rolling bearings, making this drive train much more robust than other where the wheels are directly mounted on the motors. Figure 3.2B and 3.2C shows a practical implementation of this Figure 3.2A technique on one of our early robots, where each wheel is mounted to a 6mm steel shaft, supported at both ends with rolling bearings. There is no obligation to put the rolling bearing at both sides of the wheel (the two rolling bearing can be placed at the same side of the wheel as in figure 3.2A) but you have to put two of them, each one as distant from the other as possible, to reduce shear stresses on the rolling bearings. (rolling bearings are designed to withstand very high radial stresses). While you're looking at the pictures, you can notice how the motors are mounted with pipe clamps as explained before.

Figure 3.2B

Figure 3.2C

4-Diameter of the wheels, speed and torque
With a constant output RPM from a motor, The diameter of the wheel is the last criteria that can affect the the balance between the torque of the robot and it's linear velocity. Consider the wheel in figure 4, having a radius r turning with a constant angular velocity (RPM) w, P a point on the circumference of the wheel, T the torque developed from the motor acting on the ground plane and F the reaction force of the ground on the wheel. Let Tf be the torque developed by the ground as reaction to the wheel's movement. This is the torque resisting the robot's movement. For the robot to move from rest (or to accelerate), T must be bigger than Tf . The toque Tf = F .r .......(1) Also note the that the linear velocity of the robot equals the linear velocity of any given point on the outer circumference of the wheel, Then the velocity V = w.r .......(2)
Figure 4 From the relations (1) and (2), you can easily deduce that increasing the radius of the wheel will increase the velocity of the robot, but also increase the resisting torque that the robot have to overcome. Thus, varying the radius of the wheel, you can make a compromise between linear velocity and torque of the robot.

5-Mass distribution, Moment of Inertia and robot stability
One of the most important phenomenon that can affect the behavior of moving robots is the moment of inertia. The moment of inertia, which is different for each shape, size, weight and trajectory of a moving rigid body, is the ability of that rigid body to resist a change in its velocity. The force developed by the moment of inertia appears at the center of gravity of the body, and acts as a mechanical moment around the pivot point of the robot (usually a wheel) in the a direction opposing the change of velocity. In order to better understand the effect of mass distribution on the moment of inertia and consequently on the stability of a moving robot, let's imagine this scenario where a simple robot (as shown in figure 5.A) is moving at a constant velocity in the horizontal direction. Recalling the second law of Newton, and noting that the acceleration of the robot equals zero,

the force F1 moving the robot forward equals the resistance force R1 (which is the sum of all mechanical friction losses in the system). The stability problem will start to appear when this moving robot will suddenly stop. In that situation, there is a change of velocity, a deceleration or a negative acceleration as some books states and the moment of inertia of the robot will resist this change of velocity, by generating a force acting in the previous direction of motion, trying to keep the robot moving in the same direction, with the same velocity. In figure 5.B, the effect of the moment of inertia is somehow exaggerated to clearly show the unstability that can be caused by this problem. To solve this problem, and design robots that have very low inertia, you have to understand those two main factors that affect the inertia of a body: A- The position of center of gravity has to be as near as possible from the ground or from the eventual pivot point (which are the wheels in case of our example robot). This is verified by the mathematical relation that state that: I = m.(r^2) Where I is the moment of inertia, m the mass of the body, r the distance between the center of mass of the body and the pivot point To change the position of the center of mass of your robot, you have to lower the position of the heavy parts of the robots like the batteries and the motors. You also have to design the chassis to be as near as possible from the ground (as shown in figure 5.C). If all that is not enough, or if the chassis simply isn't heavy enough, it's common practice to add additional weights as near as possible from the ground with the sole purpose of lowering the overall center of mass of the robot. B- The torque developed by the moment

Figure 5.A

Figure 5.B

Figure 5.C

of inertial depends on the rate of change of velocity (the acceleration). You can greatly decrease the effect of inertia by controlling the acceleration and deceleration of your robot, through ingenious speed control algorithms

6-Finding motors and building material
The easiest way to acquire all the material and equipment you need to build a robot, is to buy it! But that's not the cheapest way, and sometimes you won't find all what you need in the stores. That's why - if you plan to dig your way in the field of robotics - you should start collecting all

kind of devices from which you can scavenge all kind and sizes of DC motor, mechanical parts, gears, pulleys, etc. From my experience, I tried to classify the kind of devices from which you could extract useful items, at least, this is what I do with those devices before throwing them away. Old cassette players and walkmans: Small Motors, pulleys, belts, gears. Old Floppy disk and CD-ROM drives: Very small motors, worm gear, sliding mechanism, gears, limit switches Old Photocopier machines, printers and scanners: quality Gearhead DC motors, sliding mechanisms, rubber wheels, gears. As for the chassis, it can be built with a multitude of materials. My preferred material is Copper boards (made for PCBs) as you can solder many metals to it like screws and nuts, you can also design the main board of the robot on the same board to reduce size, weight and cost. My second best choice is the Fiberglass. It can be easily formed with a a cutter, can be easily drilled, can sustain high stresses, and looks very neat an professional. Another good choice for building the chassis of the robot is the 3mm Medium Density fibers (MDF wood) which has the advantage of being very cheap, and can be very easily cut, drilled and grinded to any shape you want. The only disadvantage of this material is that it can easily deteriorate with water or even too high humidity. Those were the material I found to be more suitable for this category of robots.

Discussion (Last 15 posts preview...)
Preview of the last 15 messages discussing this page. Messages are sorted from the newest to the oldest.

Follow this discussion in the Full-featured forum
Posted by:

demonhacker
on: 10 Jun 2009

Re: Small Robot Drive Trains
Quoting ikalogic: Quote: sir , i am very thankful for all this guidance but i want to know that how aerodynamics is used to make robotics?

[ 'Quote ]

buddy your question is irrelevant.please elaborate your query so that the other person gets the clear idea of your concern.

Posted by:

Re: Small Robot Drive Trains

[ 'Quote ]

Quoting abhigem_126: hey, i am building a differential drive that can move on all kind of terrains, namely sand, peebles, greasy path, water ditch, bumper... etc. can u guys help me with what kind of wheels to use??? what kinda grip to use???

ikalogic
on: 07 Oct 2008

Search on e-bay for modeling and hobby wheels, you should find what you need small advice from a mechatronics engineer: start by chosing your motors, and depending on their couple, chose the biggest possible diameter for the wheels, that will still be small enough to deliver enough couple to move your robot around all those terrains...

Posted by:

abhigem_126
on: 07 Oct 2008

Small Robot Drive Trains

[ 'Quote ]

hey, i am building a differential drive that can move on all kind of terrains, namely sand, peebles, greasy path, water ditch, bumper... etc. can u guys

help me with what kind of wheels to use??? what kinda grip to use???
Posted by:

Re: Small Robot Drive Trains

[ 'Quote ]

ikalogic
on: 19 Aug 2008

Quoting gyaanguru: hello we are working on a project in which we trying to make a robotic arm on a moving base. . since we are all electrical students we are having a bit of difficulty in designing base and finding motors. the total weight of the arm + batteries (lead acid) +electronics = 7 kg . could you please tell me the type of motor required in terms of torque. how do we calculate the torque requirements in general. preferably a speed of 0.6m/s (2 ft/sec) is required. could to teach us how to go about these calculations thank u

I could, but the first thing you have to know is that it would be big mistake to put all that weight on the robot. you have to keep all the batteries, motors, and electronics on the fixed base, and use wire systems to transmit the mechanical power to the different parts of the ARM...
Posted by:

gyaanguru
on: 18 Aug 2008

Small Robot Drive Trains

[ 'Quote ]

hello we are working on a project in which we trying to make a robotic arm on a moving base. . since we are all electrical students we are having a bit of difficulty in designing base and finding motors. the total weight of the arm + batteries (lead acid) +electronics = 7 kg . could you please tell me the type of motor required in terms of torque. how do we calculate the torque requirements in general. preferably a speed of 0.6m/s (2 ft/sec) is required. could to teach us how to go about these calculations thank u Re: Small Robot Drive Trains
[ 'Quote ]

Posted by:

Quoting saif: about 15cm dia... v had decided on 20cm but since most of the college competitions here in bangalore(india) fix the maze width at abt 20-25cm max.. nd aso they fix a max limit to ur chassis width as sumthin lik 20cm.. so that is it-15 cm... u think its too less?

ikalogic
on: 23 May 2008

15cm is more than enough, and with that size of robots, you can use the PCB material for the chassis, as in our mini line follower robot project. I think it is the most suitable for that size
Posted by:

saif
on: 23 May 2008

Re: Small Robot Drive Trains

[ 'Quote ]

about 15cm dia... v had decided on 20cm but since most of the college competitions here in bangalore(india) fix the maze width at abt 20-25cm max.. nd aso they fix a max limit to ur chassis width as sumthin lik 20cm.. so that is it-15 cm... u think its too less? Re: Small Robot Drive Trains
[ 'Quote ]

Posted by:

ikalogic
on: 22 May 2008

Quoting saif: salam... hey vr actually designing a chassis which v decided to be cicular with just 2 wheels nd passive skids.. is a circular chassis ok wid u? v decided on it coz it can rotate freely in any direction easily... even a 360 turn... nd wot material do u recommend 4 the chassis? it shud be light as well as sturdy.. nd do u recommend a lead acid or nicad battery?

circuilar is ok, but, as fr the material of the chassis, i can't tell you unless you tell me, what is the size of your robot? same thing for the battery.

so, what's the size of your robot?
Posted by:

saif
on: 22 May 2008

Small Robot Drive Trains

[ 'Quote ]

salam... hey vr actually designing a chassis which v decided to be cicular with just 2 wheels nd passive skids.. is a circular chassis ok wid u? v decided on it coz it can rotate freely in any direction easily... even a 360 turn... nd wot material do u recommend 4 the chassis? it shud be light as well as sturdy.. nd do u recommend a lead acid or nicad battery? Re: Small Robot Drive Trains
[ 'Quote ]

Posted by:

Quote: how can we construct a small robort which has only 2 wheels and can turn and move in any direction

ikalogic
on: 28 Feb 2008

Good question! You can either do it the easy way, which is to use 'skids' that will act just as a wheel but with more friction.. Or you can do it the hard way, wich is to build a robot with only 2 weels in the midle, and to constantly accelerate and decelerate the wheels, acting on the moment of intertia of the robot to stabilise it.. or maybe you have to have a mean of changing the center of gravity of the robot to give it the ability to balance itself horrisontally.. there lot of ongoing researches about this subject.. you may find some information on wikipedia.. hope this answers your question.

Posted by:

Re: Small Robot Drive Trains

[ 'Quote ]

Quote: sir , i am very thankful for all this guidance but i want to know that how aerodynamics is used to make robotics?

ikalogic
on: 28 Feb 2008

Well, unless you wroking with robots that go in the air on in the sea, or that are very fast, aerodynamics usually is not a big concern. I honnestly don't have a lot of experience in this field so i can't give you more information. good luck

Posted by:

Small Robot Drive Trains discussion for the page: [link]

[ 'Quote ]

Quote: sir i have gone through the site,i want to know which motor is prefered for the better efficiency of the robots.(what type it is?)

ikalogic
on: 28 Feb 2008

Gearhead DC motors (which are normal brushed DC motors, with a gearbox attached to it's output shaft, to decrease speed and increase torque)

You have to be a member to post replies.
Username: Password: b Remember me c d e f g
Login

Register now! it only takes an instant. Forgot your password?

Home | Forums | contact | Check mail | About Ibrahim KAMAL
All content on this site is provided as is and without any guarantee of any kind. We cannot be held responsible for any errors, omissions, or damages arising out of use of information available on this web site.

IMPORTANT COPYRIGHT NOTE: Electronics and Robotics Articles by Ibrahim KAMAL are licensed under a Creative Commons Attribution-Noncommercial-No Derivative Works 3.0 United States License.

Sponsor Documents

Or use your account on DocShare.tips

Hide

Forgot your password?

Or register your new account on DocShare.tips

Hide

Lost your password? Please enter your email address. You will receive a link to create a new password.

Back to log-in

Close