Specs
Content
Mark Ervin B. Benedicto ECE5-1 SONY ERICSSON RNC 3810 Fast network roll-out Easy to find site space: thanks to the small footprint of RNC 3810, it is easy to find a place where RNC 3810 can be installed; Installation: when delivered from factory, the RNC 3810 is pre-tested and preloaded with current software (SW); Network configuration: the RNC 3810 is supported with TEMS and OSS-RC to allow fast and efficient network configuration. Efficiency Compact: the RNC 3810 provides high capacity per footprint or volume; Transmission: several ATM and IP interface types are supported; the RNC 3810 can act as traffic concentrator and switch; Radio resource management: using advanced power, admission, congestion, and quality control algorithms, the RNC 3810 minimizes the interference, guaranteeing optimal usage of the available radio spectrum. High reliability and availability Redundancy: the RNC 3810 is designed with redundancy for all hardware (HW), and has no single point of failure; Hot-repair: hardware boards can be replaced and/or added while the RNC 3810 is in operation; Soft software upgrade: corrections and upgrades can be made while in operation; Fault pin-pointing: root-cause fault pin-pointing for short restore time. Flexibility Modular product configurations: the RNC 3810 provides a modular hardware architecture where all configurations are created from a limited set of building blocks, 1-6 sub-racks (shelves) in 1-2 cabinets, using only 6 basic types of boards; Expandability: all expansions up to the maximum RNC 3810 configuration are handled without disturbing on-going traffic; Evolution: the RNC 3810 is designed for easy introduction of new technologies, new product packages based on new hardware but with the same architecture and new radio and transmission functionality; O&M access: the RNC 3810 O&M functionality is accessible from any node in the network, making the management task available for everyone everywhere (only limited to user rights); Service convenience: the same RNC 3810 HW configuration handles any service mix, i.e., changing user traffic patterns do not require changes in HW or SW configurations; SW-centric solution: new services such as HSDPA and Enhanced Uplink can be introduced without addition of new HW; Pooling: processing resources are pooled for efficient resource sharing and redundancy.
RBS 3206 The RBS 3206 is an indoor macro RBS, based on the RBS 3000 R3 hardware, and a member of the RBS 3000 family. Main Features The main features of RBS 3206 are the following: A complete RBS in a four-subrack cabinet with a standard footprint Can be equipped with various Radio Units (RU) Can be equipped with transport network interface boards, which support E1, J1, T1, E3, T3, STM-1/OC3c or STM-1/OC-3 Can perform antenna sharing with Global System for Mobile Communications (GSM) and Time Division Multiple Access (TDMA) systems Variable baseband capacity uplink and downlink for RBS 3206F and RBS 3206E with up to 1,536 Channel Elements (CE) Variable baseband capacity uplink and downlink for RBS 3206M with up to 768 Channel Elements (CE) Supports High-Speed Downlink Packet Access (HSDPA) Power supply alternatives for RBS 3206E: +24 V DC, 48 V DC (two-wire), 48 V DC (three-wire), and 120 250 V AC Power supply alternatives for RBS 3206F: +24 V DC, 48 V DC (two-wire), 48 V DC (three-wire), and 120 250 V AC Optional prioritized power for RBS 3206F: 48 V DC (two-wire) Power supply alternative for RBS 3206M: 48 V DC (two-wire) Two-way RX diversity, two-way TX diversity (optional), and four-way RX diversity (optional) Can be equipped and configured to support multiple frequency bands RBS 3206M: Can be configured for 1 3 sectors, with up to two carriers per sector RBS 3206F and RBS 3206E: Can be configured for 1 6 sectors, with up to four carriers per sector Supports external alarm equipment Supports the Global Positioning System (GPS) as a synchronization source Supports Ethernet-based site Local Area Networks (LAN) (optional) Supports GSM or WCDMA Tower-Mounted Amplifiers (TMA), Antenna System Controller (ASC), RET Interface Unit (RIU) and Remote Electrical Tilt Units (RETU) HUAWEI BSC6810 Product Features & Advantages Advanced Network Sharing Solutions for cutting costs The BSC6810 uses the advanced RAN sharing, lu Flex, and multiple operator core network (MOCN) functions to meet the requirements for shared networks among multiple telecom operators. Through the newly introduced MOCN function, the RNC can be connected to the core networks of different telecom operators, thus enhancing the network sharing function. This, in turn, helps the telecom operators in reducing costs. Advanced Solutions Promising Higher Speed for Data Services The BSC6810 uses advanced technologies, such as HSDPA, HSUPA, HSPA+, and MBMS, to meet the requirements of different types of data service. As a newly introduced technology based on HSUPA and HSDPA, HSPA+ further improves the network performance and expands the network capacity. All-IP Platform Meeting the Varying Needs for Network Evolution Based on its all-IP platform, the BSC6810 UMTS improves the PS service performance. The interfaces support IP transmission, which provides sufficient bandwidth and cuts transmission cost. GSM/UMTS Co-Platform Ensuring Smooth Evolution
The BSC6810 shares the hardware platform with the GSM/UMTS dual-mode network controller and supports smooth evolution to the GSM/UMTS dual-mode network controller. In this way, fewer spare parts are required.
DBS3800 Key characteristics y HSPA: 1.92Mbps(UL)/14.4Mbps(DL) y Multi carrier Doherty PA y Transmitting Diversity y 4-way Receiving Diversity y RET with AISG interface y ATM/IP transmission y Multi-band co-BBU Technical Specification y Full Frequency Range: 1800MHz 1900MHz 2100MHz 850M 900M y Number of Cells: 12 Cells y Number of Sectors: 6 Sectors y Dimension (H×W×D) BBU: 42×436×300 (mm), RRU: 610×380×200(mm) y Weight BBU: 5 kg, RRU: 20kg y Output Power: 40W y Max power consumption BBU: 60W, RRU: 240W y Receiver Sensitivity -126.2dBm (Single Antenna without TMA) y Power Supply BBU: 24VDC/-48VDC, RRU: -48VDC/220V AC y Temperature Range BBU: -5~55 °C, RRU: -40 to +50 °C NOKIA TALK FAMILY Nokia Intratalk GSM 900/1800 BTS y Flexible configurations - Omnidirectional 6 TRX - Tri-sector 3*2 TRX (one cabinet) - Tri-sector 3*4 TRX (two cabinets) - Tri sector 3*1+1 TRX (with floating redundant transceiver) y AC or DC power supply y Integrated radio links Nokia Citytalk GSM 900/1800 BTS y Ease of installation through lightweight aluminium cabinet y Flexible configurations y Omnidirectional 6 TRX y Tri-sector 3*2 TRX (one cabinet) y Tri-sector 3*4 TRX (two cabinets) y Tri sector 3*1+ 1 TRX(with floating redundant transceiver) y Integrated radio links
y AC / DC power supply y Close-circuit internal air flow Nokia Extratalk GSM 900/1800/1900 y Battery back-up (BBU) - AC input, DC output - Typical back-up time 1 hour (tri-sector 3*1 TRX) - Redundant rectifier y Space for Line Terminal Equipment (LTE) - 19 , 6 U height subrack y Applications - Intratalk BTS - Citytalk BTS - Flexitalk BTS (as a transmission node) NOKIA Flexitalk GSM 900/1800 BTS Erase of installation throughcompact size - Wall mountain indoors - Shopping malls - Rooftops - Special sites such as tunnels y Efficient size/capacity - 1-2 TRX omni y AC/DC power supply y Twisted pair / coaxial 2 Mbit/s links - Support for Nokia microwave radio SITE FAMILY Nokia MetroSite Base Station y Size: 870 x 310 x 215 mm (H x W x D) y Volume: 49 l y Weight: 1 TRX BTS 22 kg; 2 TRX BTS 26 kg; 3 TRX BTS 31 kg; 4 TRX BTS 40 kg y Heaviest single unit 8 kg (chassis) y Vertical and horizontal mounting possible y Wall and pole mounting y For indoor and outdoor installations Clear and well-defined architecture y Modular mechanics: Cabinet mechanics and 8 plug-in units Minimised internal cabling Two-level environmental protection: BTS is shielded against water, snow and solid foreign objects by cover EMC-shielded and weatherproof plug-in units Nokia InSite Base Station General Characteristics y TRX capacity for all GSM frequency bands y Optimized output power for indoor use y Integrated antenna y Built-in transmission interfaces
y Battery backup time 30 min y Automatic Picocell Planning y Channel Finder y Silent Operation Nokia UltraSite GSM Base Station Types 1. Outdoor Up to 12 TRXs 1840 x 770 x 750 mm(H x W x D) 2. Indoor Up to 12 TRXs or 6 TRXs and 3 WCDMA carriers 1700 x 600 x 570 mm 3. Midi Indoor Up to 6 TRXs 1170 x 600 x 570 mm Nokia UltraSite Functionality y HSCSD y GPRS y EDGE y WCDMA Nokia UltraSite supports HSCSD, GPRS and EDGE right from the beginning. Nokia UltraSite will allow integration of WCDMA. Nokia UltraSite has integrated transmission capacity for all foreseeable needs. Nokia UltraSite Combines GSM, EDGE and WCDMA y Data speed support up to 2Mbit/s y Single cabinet can house simultaneously - Either 12GSM/EDGE transceivers or 6 GSM/EDGE and 3 WCDMA carriers y Operates on GSM 900, 1800, 1900MHz and WCDMA 2 GHz frequencies y For fast and cost-efficient EDGE and WCDMA rollout
RBS 3206 The RBS 3206 is an indoor macro RBS, based on the RBS 3000 R3 hardware, and a member of the RBS 3000 family. Main Features The main features of RBS 3206 are the following: A complete RBS in a four-subrack cabinet with a standard footprint Can be equipped with various Radio Units (RU) Can be equipped with transport network interface boards, which support E1, J1, T1, E3, T3, STM-1/OC3c or STM-1/OC-3 Can perform antenna sharing with Global System for Mobile Communications (GSM) and Time Division Multiple Access (TDMA) systems Variable baseband capacity uplink and downlink for RBS 3206F and RBS 3206E with up to 1,536 Channel Elements (CE) Variable baseband capacity uplink and downlink for RBS 3206M with up to 768 Channel Elements (CE) Supports High-Speed Downlink Packet Access (HSDPA) Power supply alternatives for RBS 3206E: +24 V DC, 48 V DC (two-wire), 48 V DC (three-wire), and 120 250 V AC Power supply alternatives for RBS 3206F: +24 V DC, 48 V DC (two-wire), 48 V DC (three-wire), and 120 250 V AC Optional prioritized power for RBS 3206F: 48 V DC (two-wire) Power supply alternative for RBS 3206M: 48 V DC (two-wire) Two-way RX diversity, two-way TX diversity (optional), and four-way RX diversity (optional) Can be equipped and configured to support multiple frequency bands RBS 3206M: Can be configured for 1 3 sectors, with up to two carriers per sector RBS 3206F and RBS 3206E: Can be configured for 1 6 sectors, with up to four carriers per sector Supports external alarm equipment Supports the Global Positioning System (GPS) as a synchronization source Supports Ethernet-based site Local Area Networks (LAN) (optional) Supports GSM or WCDMA Tower-Mounted Amplifiers (TMA), Antenna System Controller (ASC), RET Interface Unit (RIU) and Remote Electrical Tilt Units (RETU) HUAWEI BSC6810 Product Features & Advantages Advanced Network Sharing Solutions for cutting costs The BSC6810 uses the advanced RAN sharing, lu Flex, and multiple operator core network (MOCN) functions to meet the requirements for shared networks among multiple telecom operators. Through the newly introduced MOCN function, the RNC can be connected to the core networks of different telecom operators, thus enhancing the network sharing function. This, in turn, helps the telecom operators in reducing costs. Advanced Solutions Promising Higher Speed for Data Services The BSC6810 uses advanced technologies, such as HSDPA, HSUPA, HSPA+, and MBMS, to meet the requirements of different types of data service. As a newly introduced technology based on HSUPA and HSDPA, HSPA+ further improves the network performance and expands the network capacity. All-IP Platform Meeting the Varying Needs for Network Evolution Based on its all-IP platform, the BSC6810 UMTS improves the PS service performance. The interfaces support IP transmission, which provides sufficient bandwidth and cuts transmission cost. GSM/UMTS Co-Platform Ensuring Smooth Evolution
The BSC6810 shares the hardware platform with the GSM/UMTS dual-mode network controller and supports smooth evolution to the GSM/UMTS dual-mode network controller. In this way, fewer spare parts are required.
DBS3800 Key characteristics y HSPA: 1.92Mbps(UL)/14.4Mbps(DL) y Multi carrier Doherty PA y Transmitting Diversity y 4-way Receiving Diversity y RET with AISG interface y ATM/IP transmission y Multi-band co-BBU Technical Specification y Full Frequency Range: 1800MHz 1900MHz 2100MHz 850M 900M y Number of Cells: 12 Cells y Number of Sectors: 6 Sectors y Dimension (H×W×D) BBU: 42×436×300 (mm), RRU: 610×380×200(mm) y Weight BBU: 5 kg, RRU: 20kg y Output Power: 40W y Max power consumption BBU: 60W, RRU: 240W y Receiver Sensitivity -126.2dBm (Single Antenna without TMA) y Power Supply BBU: 24VDC/-48VDC, RRU: -48VDC/220V AC y Temperature Range BBU: -5~55 °C, RRU: -40 to +50 °C NOKIA TALK FAMILY Nokia Intratalk GSM 900/1800 BTS y Flexible configurations - Omnidirectional 6 TRX - Tri-sector 3*2 TRX (one cabinet) - Tri-sector 3*4 TRX (two cabinets) - Tri sector 3*1+1 TRX (with floating redundant transceiver) y AC or DC power supply y Integrated radio links Nokia Citytalk GSM 900/1800 BTS y Ease of installation through lightweight aluminium cabinet y Flexible configurations y Omnidirectional 6 TRX y Tri-sector 3*2 TRX (one cabinet) y Tri-sector 3*4 TRX (two cabinets) y Tri sector 3*1+ 1 TRX(with floating redundant transceiver) y Integrated radio links
y AC / DC power supply y Close-circuit internal air flow Nokia Extratalk GSM 900/1800/1900 y Battery back-up (BBU) - AC input, DC output - Typical back-up time 1 hour (tri-sector 3*1 TRX) - Redundant rectifier y Space for Line Terminal Equipment (LTE) - 19 , 6 U height subrack y Applications - Intratalk BTS - Citytalk BTS - Flexitalk BTS (as a transmission node) NOKIA Flexitalk GSM 900/1800 BTS Erase of installation throughcompact size - Wall mountain indoors - Shopping malls - Rooftops - Special sites such as tunnels y Efficient size/capacity - 1-2 TRX omni y AC/DC power supply y Twisted pair / coaxial 2 Mbit/s links - Support for Nokia microwave radio SITE FAMILY Nokia MetroSite Base Station y Size: 870 x 310 x 215 mm (H x W x D) y Volume: 49 l y Weight: 1 TRX BTS 22 kg; 2 TRX BTS 26 kg; 3 TRX BTS 31 kg; 4 TRX BTS 40 kg y Heaviest single unit 8 kg (chassis) y Vertical and horizontal mounting possible y Wall and pole mounting y For indoor and outdoor installations Clear and well-defined architecture y Modular mechanics: Cabinet mechanics and 8 plug-in units Minimised internal cabling Two-level environmental protection: BTS is shielded against water, snow and solid foreign objects by cover EMC-shielded and weatherproof plug-in units Nokia InSite Base Station General Characteristics y TRX capacity for all GSM frequency bands y Optimized output power for indoor use y Integrated antenna y Built-in transmission interfaces
y Battery backup time 30 min y Automatic Picocell Planning y Channel Finder y Silent Operation Nokia UltraSite GSM Base Station Types 1. Outdoor Up to 12 TRXs 1840 x 770 x 750 mm(H x W x D) 2. Indoor Up to 12 TRXs or 6 TRXs and 3 WCDMA carriers 1700 x 600 x 570 mm 3. Midi Indoor Up to 6 TRXs 1170 x 600 x 570 mm Nokia UltraSite Functionality y HSCSD y GPRS y EDGE y WCDMA Nokia UltraSite supports HSCSD, GPRS and EDGE right from the beginning. Nokia UltraSite will allow integration of WCDMA. Nokia UltraSite has integrated transmission capacity for all foreseeable needs. Nokia UltraSite Combines GSM, EDGE and WCDMA y Data speed support up to 2Mbit/s y Single cabinet can house simultaneously - Either 12GSM/EDGE transceivers or 6 GSM/EDGE and 3 WCDMA carriers y Operates on GSM 900, 1800, 1900MHz and WCDMA 2 GHz frequencies y For fast and cost-efficient EDGE and WCDMA rollout
