Specs

Published on December 2016 | Categories: Documents | Downloads: 76 | Comments: 0 | Views: 722
of 20
Download PDF   Embed   Report

Specification list

Comments

Content

Description G

Spec Brand

Unit Model Type country Capacity

value

A/C AHU Saiver/TraneCLCP IOM Malasia/ Ireland( China) Outdoor Saiver/TraneRAUP 250/ 17ton Oil POE (160SE) Bearing type Coupling type Belt type Refregerent R402 Compressor Hepafilter VSD Star- Delta Heater Expansion valve Ducting P3 ducting Insulation Damper Cu tube Cu insulation Compressor Keaser sk25 Capacity l/s Pressure bar Power kW Power supply Mains Fusing Cable Current Motor protection reciver l rpm Option K1--------------C3 Drier TC 36 Refrengeration dryer Refregerent R134A Ref Charge .97kg Ref pressure 16-18 bar Tested leak free 16 bar Max working pressure (Air side) Power supply 230V/1 Phase/ 50Hz/7A Ambient temp 3-43C Oil Charge 7 ltr Oil filter Oil Synthetic FG 460 or FG 680 Viscosity 40 C 50.7/70 Viscosity 100 C 8.2/10.4 Flash point 245 C Bearing type Coupling type Flange type Belt type Generator Cat 3306/3300, 220kW/0.8 pf/ 50 Hz, Y connected, Series Class F insulation, Max temp 130C

3kW 13kW

Armaflex

25 8 15 35A 6mm2 32A IP 54 1000 3000

KVA Current Excitation Engine rpm hp Oil Bearing type Coupling type Flange type Belt type Chain cylinder crank stroke Bore Governer AVR Star Delta Electrical MDB SMDB SDB D. Anly MCCB MCB RCCB ELCB ATS EFR PFR ELR Industrial socket Isolator Sockets Encloser

275 kVA 49V, 9.2A 4 cylinder 1500

400A/4P MCCB (with ATS, EFR,PFR,D.Anly,MCCB(250A,160,125,100,63A)) 160A/TP, Digital Analyzer 250A,160A,125A,100A,63A,/4P&3P (40A,32A,16A,20A,10A/ 4P,3P,DP & SP) 32A/100mA for machine, 20A/30mA for L&P

IP 65 Padlockable both male &female16A, 5 pin(MK, SCAME,HENSAL) IP 65 Padlockable both male &female32A, 5 pin(MK, SCAME,HENSAL) 5A,13A Singel switch, 13A twin switch IP 65 rated, consealed, polycarbonate type tested, Wall mounted (Waterproof, washable with direct waterjet)

Main Cable 4C/185mm2/-PVC/SWA/XLPE/Cu Feeder Cables Feeder piller - MDB 1 X 4C 185mm2 Cu/XLPE/SWA/PVC Armoured cable Generator -MDB 1 X 4C 185mm2 Cu/XLPE/SWA/PVC Armoured cable MDB-SMDB (Hotsip M/C) 1 x 4C 35mm2 Cu/XLPE/PVC +16mm2Earth MDB-SMDB (Iodex M/C) 1 x 4C 50mm2 Cu/XLPE/PVC +25mm2Earth MDB-SMDB (Hotsip L &P) 1 x 4C 16mm2 Cu/XLPE/PVC +16mm2Earth MDB-SMDB (Iodex L &P) 1 x 4C 16mm2 Cu/XLPE/PVC +16mm2Earth MDB-SMDB (Hotsip Utility) 1 x 4C 16mm2 Cu/XLPE/PVC +16mm2Earth MDB-SMDB (Hotsip A/C) 1 x 4C 50mm2 Cu/XLPE/PVC +25mm2Earth MDB-SMDB (Iodex A/C) 1 x 4C 25mm2 Cu/XLPE/PVC +16mm2Earth MDB-SMDB (Hotsip A/C-2) 1 x 4C 25mm2 Cu/XLPE/PVC +16mm2Earth MDB-SMDB (Hotsip A/C-3) 1 x 4C 16mm2 Cu/XLPE/PVC +16mm2Earth SMDB L&P-SDB L&P 1 X 2C10mm2 Cu/XLPE/PVC+10mm2 SMDB Iodex M/C - SDB Iodex1M/C x 4C 35mm2 Cu/XLPE/PVC +16mm2Earth SMDB Hotsip AC -SDB Hotsip1 AC x 4C 25mm2 Cu/XLPE/PVC +16mm2Earth SMDB- Hotsip MC isolator (16A) 4 X 1C 4mm2 PVC/Cu + 4mm2 SDB - Hotsip AC isolator (15kW 1 xunit) 4C 10mm2 Cu/XLPE/PVC +10mm2Earth

SDB - Hotsip AC isolator (6kW 1 AHU) x 4C 6mm2 Cu/XLPE/PVC +6mm2Earth SMDB L&P - Industarial socket 4 x 1C 6mm2 C/PVC +6mm2Earth Hoist (16A) 4 X 1C 4mm2 PVC/Cu + 4mm2 Compressor (32A) 1 x 4C 6mm2 Cu/XLPE/PVC +6mm2Earth Mfg vessel 1 x 4C 25mm2 Cu/XLPE/PVC +16mm2Earth Lighting 2 X1C 1.5mm2 Cu/PVC +2.5mm2 Earth Sockets 13A 2 X1C 2.5mm2 Cu/PVC +2.5mm2 Earth 5 pin industrial sockets (16 A) 4X1C 2.5mm2 Cu/PVC +2.5mm2 Earth 6 pin industrial sockets (32 A) 4X1C 4mm2 Cu/PVC +2.5mm2 Earth 5A socket 2X1C 1mm2 Cu/PVC +2.5mm2 Earth Cable tray Hotdip galvanized Light fittings Hotsip & Iodex primery 4 X 28W recessed mount diffuser type T5 fluorscent fitting withelectronic ballast with acrylicsheet diffuser 2 X 28 W _Do_ 1 X 18 W -DoPacking 13W recessed mount down lamp Outdoor IP 65 rated wall lamp Earthing Surge arrester Switches IP 65 Lighting protection Earth Inspection points Fire Smoke detecor Heat detector loop Fire pannel Alarm Manuel call point Glass berak Cables Steam Pipe Insulation Welding rod Stainer Bellow Flange PRV Steam trap Gate valve Support 25mm2Cu/PVCearth conductor- Nauta, 50mm2Cu/PVC -MDB, 25 X3mm Cu tape Interlink the grounding pointe

ESE type

PHE & Hot water Flow rate Tin Tout S/S pipe Ball cock valve

Ball trap Spray ball Non return valve Gas purging Ar Cylinder TIG plant rod size current Schedule Hot water pump Flowrate Head Inlet Outlet Impeller Housing Motor Power current rpm Vacuum Inlet Outlet Pressure Motor rmm hp Current Hoist Capacity Motor Dimensions Safety interlock Compressed air Piping Valve

Manufacturing Dia /mm Height/mm Air pressure (bar) Capacity (l ) Jacket Insulation Vacuum gauge Stirr Motor Power rmp

500 kg (600l ), 600l overflow Premix Wax meltingMfg Storage 850 1050 750 750 4.5-6 bar 4.5-6 bar 400Net/ 500gross 500N / 800G

50mm Rockwool 50mm Rockwool 0-760mm Hg top,50mm shaft 415V/ IP 65/ Class F insulation 2.75kW 1440

Gear size Gear type Ratio Oil Steam inlet Jacket pressure (bar) Hydraulic test pressure (bar) Design pressure (bar) Design temperature C Steam trap Condensate Jacket safety valve Jacket pressure gauge Vessel pressure Vessel design temperature Working temp Bearing Coupling type Flange type Belt type Chain Stirer shaft Sensor

W110 Worm & wheel 1:30 1" TC 3 5 3.5 150 1" Thermodynamic trap Steam trap

3/8” BSP Set at 3 kg/cm²
0-7kg/cm2 Water fill 100 5-95 C

Probe Dia. Probe Length Elec. Connection

Pt 100 6mm 100mm

Range Accuracy
Hot filling

0-200 deg C Class A

Capacity Jar Cooling time Tunnel length Air presssure Air consumption Power requirement Motor HP Power cable size
Oil Bearing Coupling type Flange type Belt type Chain Nauta

Capacity Motor1 HP RPM Current Motor2

HP RPM Current Main cable D Height Dia
Bearing Coupling type Flange type Gear box Belt type Chain

PIAB Brand
Model

Vacuum pres Suction pipe Height Suck Air pressure
Sachet

Capacity Per min Sachet length Sachet width Sachet Vol Film reel dia Core dia Sealing temp Sealing pres Dimension Weight Power req. Current Cable Delta- star Air pres Air consum.
Servo driver Microprocessor Oil Bearing Coupling type Flange type Belt type Chain

Conveyor Power Motor brand & Model Motor rpm Motor power Motor current

L

Belt speed Roller dia WXHXL Oil Bearing Coupling type Flange type Belt type Chain DC Brand/ Model W X HXL Weight Motor brand & Model Motor rpm Motor power Motor current Hepafilter Suction pipe Fresh air duct Explosion vent Earthing Air pressure Air pulse Oil Bearing Coupling type Flange type Belt type Chain Generator Generator KVA Current Engine rpm hp cylinder crank stroke Bore Governer AVR Oil Bearing Coupling type Flange type Belt type Chain Compressor (Contessa) Capacity Pressure Power reciver Drier Oil filter

Oil Bearing Coupling type Flange type Belt type Chain

Pump Flowrate Head Inlet Outlet Impeller Housing Motor Power current rpm Oil Bearing Coupling type Flange type Belt type Chain B/P Silo Mixer Bins Oil Bearing Coupling type Flange type Belt type Chain Elumatek Holzer

Arc welding Plant Oil Welding rod Identification Current Plate thickness Gas cutting Oxygen cylinder Accetelene Cylinder Gas Cylinder Nozzel

Regulator

Heat treatments Anealing Normalizing Stress releaving Aging Quenching (Water/ Oil) Tempering Case hardening

Rh

Pump

Egger/Ksb Slurry Channel vane Up to 1500 Up tp 90 150-500 Channel vane

Slurry 2 Vortex Up to 120 Up tp 130 32-200 32-201 Vortex

Type Flowrate (l /S) Head (m) Inlet (mm) Outlet (mm) Impeller

Centrifugal Switzerland/ India Slurry Low Water dense Centrifugal Centrifugal Up to 1300 Up tp 210 50-500 50-500 Semi- Open Open impeller impeller

Channel vane

impeller material Housing Motor Power current rpm Oil Bearing Coupling type Flange type Belt type Chain Geared Motor Ratio Effi rpm Housing Wheels Oil Bearing Coupling type Flange type Belt type Chain Hydraulics Oil Flange type Pressure Control valve

Semi Open Impeller

Heavy duty roller

Hose Pump Accessories Pneumatics Pressure Control valve Hose Accessories Components

PLC DC Software Input Output Expansion modulus PPI Cable Sensor Capacitive Inductive Optical NPN PNP Relay Contactor Switch power supply Accessories Agitator Shaft diameter Motor Power rpm Current Gear box Oil Bearing Coupling type Belt type Chain turbo blender Shaft diameter Motor Power rpm Current Gear box Oil Bearing Coupling type Flange type Belt type Chain

CFM Shaft diameter Motor Power rpm Current Gear box Oil Bearing Coupling type Flange type Belt type Chain Vaccum pump Type Pressure Inlet Outlet Shaft diameter Motor power rpm Oil Bearing Coupling type Flange type Belt type Chain Silo Capacity Height Diameter Sheet thickness Filter bags Height Diameter Cloth Vibrator

AHU Check filters (Vissually) check the unit for any abnormal sound or vibration Fan belt tension & adjustment spray nozzles and float valve in air washer Check door hinges and lubricate if necessary Check Water drain Measure the pressure drop across filters. Need to clean or replace if it is 3 times of initial value Check the fan motor running current Check function controls and their effect on A.H. Unit components Check electric heater battery elements. Fan & motor bearing checking, greazing & alligning Add water and flush condensate drain pan, trap and drain line Check circulating pump and motor in air washer Check the condition of inlet strainers

Frequency Daily Weekly Monthly 3Months 6 Months YearlyRemarks Frequency Add CLCP IOM Page 26 &27/ Saiver O & M pages 37-42 Weekly Weekly Monthly Monthly Monthly Monthly Monthly Once a Six Month Once a Six Month Once a Six Month Once a Six Month Once a Six Month Once a Six Month Once a Six Month Once a Six Month Once a Six Month Once a Six Month Once a Six Month Once a Six Month Once a Six Month Once a Six Month Once a Six Month Once a Six Month Once a Six Month Once a Six Month √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √

Check the operation of dampers. Check the filter frame for proper sealing. Replace synthetic media in panel filters. Check the access doors for easy operation and proper locking. Check the controls and operation of Roll Filters. Check the coils and fin condition. Wash with water spray, if necessary. Check the condition of all insulating, regulating valves etc in the system. Vent the water coils. Check motor and fan bearing lubrication. Replace belts. Check all wiring, controls, isolating devices, terminal connections etc.

Outdoor
Check the compressor oil level. The oil should cover 1/2 of the sight glass when running at full load. Before oil is added allow the compressor to run continuously for 3-4 hours. Check the oil level every 30 minutes. If the level does not return to cover 1/2 of the sight glass contact a qualified service technician. Check smooth ref flow through sight glass Check pressure levels

Weekly



Compressor oil for R407C -POE (160SE)

Weekly Weekly

√ √

Suction Pressure (4-6) bar, Discharge Pressure (17-19 bar)

Measure the temperatures Check for any abnormal noise or vibration Perform an oil analysis to determine the acidity of oil Refregerent leak test Check motor winding insulation Check motor contactors Check function of each control

Weekly Weekly Yearly Yearly Yearly Yearly Yearly

√ √ √ √ √ √ √

shutdown & Start up procedure Generator Scheduled oil sampling (3 tests) Wear Analysis (Measure the amount of wear particles in oil) Chemical & Physical test(measures the presense of water, fuel & antifreeze) Oil condition analysis(Measures the amount of contaminents - soot, S,Oxidation & Nitration products) Weekly-Before starting engine When starting Check coolent level Operate lamp test switch and check all indicators Check battery voltage by using the selector Disconnect battery charger(Very improtant) Turn selector switch to manual start position When engine starts check rpm > 1500 Check oil pressure > 30psi Raise vpltage to 405 V by turning Voltage regulator clockwise and check all 3phases using the selector switch. Operate selector to continuously indicate rpm of the engine Re connect the batter charger When stopping Knock off MCCB of the generator Move selector switch to cool down position and allow generator to cooldown & stop. Engine crank case- Check oil level, Maintain oil level between ADD and FULL mark on the "Engine Stopped" side of the oil level gauge. Cooling system- Check coolent level. Maintain level within 13mm to bottom of filler neck or propper level on sight glass Walk-Around Inspection- Inspect the engine, radiator, and generator for debris, loose or broken fittings hoses or wires and guards and repair as necessary. Air cleaner indicator (If equipped) - Check the indicator. Change elements if indicator diaphragm remains in the locked position. Check battery charger for proper operation Fuel system- Check for leaks, Drain water separator ( if equipped) . Check fuel tank level. Check fuel filter indicator (If equipped) Belts- Inspect for worns, broken or loose belts. Asdjust if necessary Batteries- Clean up the batteries. Check electrolyte level (Unless maintenance free) . Check for loose connections. Block heater- Check for proper operation. Maintain 32o C coolent temperature in the block at all times. Governor- Check and maintain oil level. Gauges- Check the condition of all gauges. Repair or replace any broken gauge Air sustem (If equipped) - Drain water; check air pressure. Control panel- Visually inspect; check for loose brocken or damaged wiring or components. Generator- Check for moisture, dust, oils, greases, and debrison main stator windings, exciter, and PMG clean as needed

Generator space heaters (If exuipped) - check for proper operation. Weekly , with Engine Running Oil pressure gauge- Check for oil ressure. Fuel pressure gauge- Check for proper operating fuel pressure Engine crank case- Check oil level, Maintain oil level between ADD and FULL mark on the "Engine Running" side of the dipstick. (Not Apply to 3208, 3114 & 3116 engines) Frequency (rpm) & Generated voltage- Check and record readings.( Maximum 1% voltage drop after 30 minutes and 100 deg C Generator Louvers- Check for proper operation Generator Air inlet filter(If equipped). If differential pressure exceeds 0.6 inch of water, stop the engine and clean the element by soaking in hot water with detergent. Rinse with clear water. Recharge the element with a thin layer of light weight machine oil (WD- 40 or equivalent) Leaks & NoisesMaint stater winding temperature ( If e. 180 for alarm & 205 for shut downquipped with winding defectors)- Check & Record Bearing bracket temperature (If equipped)- Check & Record with the engine under load. 85 for alarm & 95 for shut down Weekly - after stopping the engine Automatic switches- Check if all swithes are in proper position for automatic start. Fuel tank- Refil if below 3/4 full Battery charger- Record charging ampherage reading Malfunctions- Report any malfunction and make necessary repairs. YEARLY - BEFORE STSRTING Walk-Around Inspection- Inspect the engine, radiator, and generator for debris, loose or broken fittings hoses or wires and guards and repair as necessary. Cooling system- Check coolent level. Maintain level within 13mm to bottom of filler neck or propper level on sight glass Fuel system- Drain water and sediment from tank. Change fuel filters Air cleaner system- Inspectand clean or replace element Governor- Check and maintain oil level. Engine crank case- Check oil level, Maintain oil level between ADD and FULL mark on the "Engine Stopped" side of the dipstic Crank case breather- clean Valve lash- Check & adjust , if necessary. Linkages- Check & adjust, if necessary. Lubricate all with MPGM grease Engine protective devices- Check; test for proper operation Batteries- Clean up the batteries. Check electrolyte level (Unless maintenance free) . Check for loose connections. Engine- Wipe down; clean as needed. Generator- Check for moisture, dust, oils, greases, and debrison main stator windings, exciter, and PMG clean as needed. Check windings with megohmmeterand record readings for reference

Generator bearing- Inspect bearings and brackets. Lubricate bearings (Not apply for 3114 & 3116 generators YEARLY - WITH ENGINE RUNNING Perform all weekly ,with running maintenance procedures first Engine crank case- Check oil level, Maintain oil level between ADD and FULL mark on the "Engine Running" side of the dipstick. (Not Apply to 3208, 3114 & 3116 engines) Generator Louvers- Check for proper operation Generator Air inlet filter(If equipped). If differential pressure exceeds 0.6 inch of water, stop the engine and clean the element by soaking in hot water with detergent. Rinse with clear water. Recharge the element with a thin layer of light weight machine oil (WD- 40 or equivalent) Engine mounts- Inspect for proper installation and loose fastners. Check for proper torque Leaks & Noises-- Check for leaks and unusual noises. Load test- Load the engine to minimum of 30% of rated load. Operate at this level for minimum of two hours. After approximately one hr record the readings of all gauges; oil pressure, fuel pressure, oil level, rpm( frequency), generated voltage, service meter, engine jacketwater temperature, exhaust tempereture (if equipped) and manifold vacuum (if equipped). Engine slobbering can occure if the testing is not conducted. Maint stater winding temperature ( If e. 180 for alarm & 205 for shut downquipped with winding defectors)- Check & Record Bearing bracket temperature (If equipped)- Check & Record with the engine under load. 85 for alarm & 95 for shut down YEARLY -AFTER STOPPING THE ENGINE Perform all weekly ,after stopping maintenance procedures first Walk-Around Inspection- Repair or adjust. Make repairs or adjustments to the engine and generator set as necessary. Report any malfunction and make necessary repairs. S.O.S Scheduled oil sampling Engine oil & filters- Change oil. Replace filters. Cut old filter open and inspect for foreign material. Generator Air inlet filter(If equipped). If differential pressure exceeds 0.6 inch of water, stop the engine and clean the element by soaking in hot water with detergent. Rinse with clear water. Recharge the element with a thin layer of light weight machi Fuel tank- Refil if below 3/4 full Battery charger- Record charging ampherage reading Automatic switches- Check if all swithes are in proper position for automatic start. Every 3 years- Before starting the engine Perform all Weekly and yearly before starting the engine maintenance procedure space heaters(If equipped) - Check for proper operation Generator- Check for moisture, dust, oils, greases, and debris on main stator windings, exciter and PMG. Clean as needed

Cooling system- drain, clean, and flush. Replace thermostats. Refill with coolant solution and conditioner. Hoses and belts- Replace; it is recommonded that all hoses and belts be replaced at this time to kinimize downtime and additional repair cost of component failures caused by these items. Batteries- Replace all batteries at this intervals Turbocharger- Inspect/ Check; Inspect for proper operation. Check the end play and radial clearence on the turbine wheel and shaft Engine- Perform a complete engine adjustment and tune up. Generator bearing- Inspect bearings and brackets. Lubricate bearings (Not apply for 3114 & 3116 generators EVERY 3 years- ENGINE RUNNING Perform all weekly & yuearly with Engine running maintenance procedures. Start the engine- Check all presure gauges, oil pressure, fuel pressure, rpm, generated voltage and engine jacket water temperature, for correct readings. Engine crank case- Check oil level, Maintain oil level between ADD and FULL mark on the "Engine Running" side of the dipstick. (Not Apply to 3208, 3114 & 3116 engines) Generator Louvers- Check for proper operation Generator Air inlet filter(If equipped). If differential pressure exceeds 0.6 inch of water, stop the engine and clean the element by soaking in hot water with detergent. Rinse with clear water. Recharge the element with a thin layer of light weight machine oil (WD- 40 or equivalent) Exhaust system- Check for leaks. Repair or replace defective components with engine stopped. Leaks & Noises-- Check for leaks and unusual noises. Load test- Load the engine to minimum of 30% of rated load. Operate at this level for minimum of two hours. After approximately one hr record the readings of all gauges; oil pressure, fuel pressure, oil level, rpm( frequency), generated voltage, service meter, engine jacketwater temperature, exhaust tempereture (if equipped) and manifold vacuum (if equipped). Engine slobbering can occure if the testing is not conducted. Maint stater winding temperature ( If e. 180 for alarm & 205 for shut downquipped with winding defectors)- Check & Record Bearing bracket temperature (If equipped)- Check & Record with the engine under load. 85 for alarm & 95 for shut down EVERY 3 YEARS- AFTER STOPPING ENGINE Perform all weekly & Yearly ,after stopping maintenance procedures first Walk-Around Inspection- Repair or adjust. Make repairs or adjustments to the engine and generator set as necessary. Report any malfunction and make necessary repairs. S.O.S Scheduled oil sampling Engine oil & filters- Change oil. Replace filters. Cut old filter open and inspect for foreign material. Coolent analysis- Obtain a sample for analysis Fuel tank- Refil if below 3/4 full

Battery charger- Record charging ampherage reading Automatic switches- Check if all swithes are in proper position for automatic start.

Compressor Check the cooling oil level Cooler:check the filter mat Control cabinet: check the filter mat Drive belt maintenance Check the air filter Clean the cooler Cooler:clean the filter mat Control cabinet:clean the filter mat Change the air filter element Cooler: change the filter mat Control cabinet: change the filter mat Change the oil filter Change the oil separator cartridge Change the cooling oil Check that all electrical connections are tight Check the pressure relief valve Check the excess temperature safety shutdown function Check the cooler for leaks Service works ( to be done by authorized technicians) Have the valves checked Check drive motor bearings Check hose lines Cooler maintenance (Ventilation grill & filter mat) Cooler cleaning (Dry brush) Air filter change (Can not be cleaned) Dry motor maintenance Bearings permanently greased. No need greasing Drive belt maintenance (Visual damage check) Checking the pressure releif valve (Page 62). Blowoff protection and air system pressure monitoring are switched off during the test. Never operate the machine without a fully functioning pressure relief valve Checking the Excess safety shutdown function. (Page 62) . Shutdown temp- 1100C Checking the Cooling Oil Level (Page63, 64). The machine has been running at least 5 minutes under LOAD.Check the oil level with machine running under LOAD (Optimum Level)

Weekly Weekly Weekly 1000hr 1000hr 1000hr 1000hr 1000hr 3000hr 3000hr 3000hr 3000hr/ At least yearly 3000hr/ At least every 3 years 3000hr- Favourable / 2000hr- Unfavourable conditions Anually Anually Anually Anually 12000hr 12000hr or 3years 36000hr or 8 years

Venting the Machine (depressurizing) (Page 64). The machine must be isolated from the air system and completely vented before undertaking any work on the pressure system.Compressed air and devices under pressure can injure or cause death if the contained energy is released suddenly or uncontrolled Isolate the machine from the air system. Venting the oil separator tank(Check that the oil separator tank pressure gauge reads 0 bar) Manually venting the air cooler.After shutting down the compressor and venting the oil separator tank, the machine is still under pressure from the air system or the section from the shutoff valve to the minimum pressure/ check valve. Topping up the Cooling Oil.The machine must be isolated from the air system and completely vented before undertaking any work on the pressure system. Slowly unscrew the filler plug 4 . Top up to bring the oil to the correct level.A sticker on the oil separator tank specifies the type of oil used Replace the filler plug's sealing ring if necessary and screw the plug into the filler neck. Starting the machine and carrying out a trial run Close all access doors; replace and secure all removable panels. Open the user's shut-off valve between the machine and the air system. After about 10 minutes, check the oil level again and top up if necessary. Switch off the machine and visually check for leaks. Changing the Cooling Oil.The machine must be isolated from the air system and completely vented before undertaking any work on the pressure system. Thoroughly drain all oil from the oil separator tank, the cooler and the heat recovery system, if fitted. Always change the oil filter and oil separator cartridge when changing the oil. Compressed air helps to expel the oil. This compressed air can be taken either from the compressoritself or from an external source. An external source of compressed air is necessary in the following cases: ■ The machine is not operational. ■ The machine is to be restarted after a long period of standstill. Changing the Oil Filter.The machine must be isolated from the air system and completely vented before undertaking any work on the pressure system. Changing the Oil Separator Cartridge.The machine must be isolated from the air system and completely vented before undertaking any work on the pressure system. The oil separator cartridge cannot be cleaned The life of the oil separator cartridge is influenced by: ■ contamination in the air drawn into the compressor, ■ adherence to the changing intervals for: ─ cooling oil ─ oil filter ─ air filter

Generator

compressed air

PHE

Hot water Steam line Mfg Hot filling Nauta Sachet DC Conveyor Compressor Compressed air Batching plant Vehicle Elumatek Holzer Pump Geared Motor Hydraulic Pneumatic PLC Silo CFM Agitator Turbo Blender Dust exhaust Conveyor

Project Management terms 6 sigma Lean 5S Kizen ISO QMS Duty cycle Maintenance terms CMMS Predictive Maintenance Preventive M Periodic M international Safety Standards Capillery tube Floating relay contact Flash point Pour point overhall varister test

Sponsor Documents

Or use your account on DocShare.tips

Hide

Forgot your password?

Or register your new account on DocShare.tips

Hide

Lost your password? Please enter your email address. You will receive a link to create a new password.

Back to log-in

Close