Tech

Published on December 2016 | Categories: Documents | Downloads: 65 | Comments: 0 | Views: 619
of 11
Download PDF   Embed   Report

Comments

Content

Norms for Accreditation-NIOS

CARPENTRY (252) FURNITURE & CABINET MAKING (354)
1. 2. The institution should have a workshop/work place of its own. The institution should have a minimum of one professional having a I.T.I. /Community Polytechnic/NIOS or equivalent Certificate in Carpentry, Furniture & Cabinet Making or Diploma in Mechanical/Civil Engineering. A person with B.Sc. or Intermediate with science subject with two years of experience in the trade may also conduct personal contact programme, practical and skill test. For a batch size of 10 students, the following equipment’s and tools are required.

3.

List of tools and equipment’s
Equipment /Tool Quanti ty Carpenter square 200mm 5 Square bevel 50mm 5 Carpenter marking gauge 10 Carpenter morose gauge 5 Hand saw 450mm & Tenon saw 10 300mm each Jack plane 335mm x 50mm cutter & 10 Smoothing plane 200mm x 50mm each cutter Chisel firmer (bevel edge) 6mm 10 10mm, 15mm, 20mm and 25mm width Chisel mortise 6mm, 10mm, 15mm 10 Screw drive 300mm cabinet maker 10 Mallet medium size 10 Oil stone 5 Tools, equipment & general out fit Spring caliper inside 150mm & Spring 4 caliper outside each Trammel 4 part Sprit level Ripsaw 600mm Plough plane with set of 8 cutter upto 12mm width Spoke shaves 50mm cutter 2 4 Equipment /Tool File half round 2nd cut 250mm File slum taper Hand drill Brad arts Gimlet set Brace Bit set for brace Carpenter pincer Parallel clamp & C. clamp Adjustable bar clamp Rasp cut file half rod 300mm Carving indifferent types Lathe wood turning 150mm Quanti ty 8 each 8 8 10 8 4 4 8 15 5 10 4 set

Height of centers 150mm, 1.75meter bed with a set of turning tools. Bench gender 200mm. Wheel d. e. 1 pedestal Portable electrician drilling machine 1 Grease gun 1

Norms for Accreditation-NIOS

WELDING TECHNOLOGY (257)
1 2. 3. The institution should have a workshop/work place of its own. The institution should have a minimum of one professional having a I.T.I. Certificate in Welding Technology trade or Diploma in Mechanical/Civil/Electrical engineering. For a batch size of 20 students, the following equipment and tools are required:

List of tools and equipment
Equipment / tools Gloves pair leather asbestos Apron/asbestos leachier Screen welding helmet type Screen welding hand Goggles pair welder Hammer scaling 0.25 kg. with handle Chisel cold flat 19mm Centre punch 9mm x 17mm Dividers 20cm Caliper outside rule 60cm two fold (inches) Wire brush 15cum x3.7cum Spark lighter Chipping screen hand Safety boots for welders Square 15cm Tongs holding 30cm Shop outfit Steel or nickel chrome rule 30cm Hammer ball per 1 kg. With handle Quanti ty 5 pairs 5 5 5 10 10 10 10 10 10 5 10 5 5 5 10 10 5 5 Equipment / tools Hammer sledge double faced 3 kg Pipe wrench 25cm and 35cm Steel tspe 182cm flexible Tinmans square 60cm x 30cm Welding torches with set of nozzles (Low/High) Earth clamps Pipe dotter (cap. 50mm dia) Oxy-acetylene torch with cutting nozzle Heavy duty blow pipe with cutting and gouging nozzles Electrode holder 400 amps Welding rubber hose, Oxygen and acetylene 8mm length Rubber hose clips Quantity 1 1 each 2 3 each 1 each 2 1set 1set 1 set

Chisel cold cross 9mm 5 Screw driver 25cm blade and 20 cm 2 each blade Vice bench 10cm 5 Number punch 6mm and letter punch 2 set 6mm Hacksaw frame adjustable 30cm 5 Hammering block 5cmthick 60sq. 1 Magnifying glass 15cm 2

5 as required as required Spindle key (for opening cylinder valve) 5 Pressure regulator oxygen double stage 2 Pressure regulator acetylene double 2 regulators Glass white 108mm x 82mm 40 Glasses coloured 108mm 82mm x 3mm din 20 11 a 13a Outfit spanner for regulator 5 Tip cleaner 10 sets Rubber hose pipe black and red 5mm (length as required) Leather sleeves 2 pairs Transformer (continuous welding current) 2 set 400amps Welding generator DC rotary set 200-300 1 set amps Welding cables (400amps) Length as required Lugs for cables - do Oxygen cutting machine (line & circle) 1 Gas welding table 822 cm x 92cm + 60cm 5

Norms for Accreditation-NIOS

Weld measuring fillet and butt File half round bostard 30cm File flat 35cm rough

2 10 10

fire bricks on stand with positioner Arc welding table all metal with positioner 5 122cm x 92cm x 60cm Trolley for cylinder (HP unit) 2 Bench shear hand capacity up to 5mm 1 DC grinder 30mm wheel motorized pedestal 2 type Portable drilling machine (cap. 6mm) 1

Spanner 12mm and 15mm double 5 ended Spanner double ended 6mm to 15mm 1set 1.5 mm C clamps 10cm, 15cm, 20cm, 30cm 1 each

Norms for Accreditation-NIOS

BIO GAS ENERGY TECHNICIAN (254)
1. 2. The institution should have installed Biogas plants Kvic drum type /Janta type/ Deenbandhu Type and workshop/ work place of its own. The institution should have a minimum of one professional having a degree (B.Sc. Ag.)/Diploma in Mechanical/Civil Electrical Engineering. A person with B.Sc./Intermediate with Science subjects and two year experience in installation & maintenance of Bio-gas plant may also conduct personal contact programmes, practical & skill test. For a batch size of 15 students, the following equipment’s and tools are required:

3.

List of tools and equipment
Equipment /tools Digester(Fixed/Mobile Model) PH meter Glass jar Glass bottle Manometer Gas valve Gas pipe fitting Gas burner Gas regulator Hammers of different weights Improved sickle/hansiya/ koyta (debgoo) Dryer oven Digestion and distillation unit Distillation water still Spirit level Files of different types & sizes Chisel Plumb bob Pipe die with bits Bench-vice Caulking tools List of consumable material Lead Chemical binder Waterproof tape Waterproofing compound Wash basin Quantity 1 1 1 1 1 1 1 2 2 2 15 1 1 1 2 10 5 2 2 2 2 (as required) - do - do - do 1 List of non-consumables Sink C.I. trap (nahani)+PVC trap Check valve ½” Ferrule ½”-1” G.I. bend Grating G.I. union ½” dia G.I. Elbow (1.25 cm) ½” dia G.I. pipes (1.25 cm) ½” G.I. Socket (1.25 cm) P.V.C. connector C.I. pipe 4” x 3” dia C.I. tee C.I. bend (diff. Size & types) P.V.C pipe 4” q P.V.C. bend 4” q P.V.C. elbow 4” q P.V.C. trap 4” q P.V.C. tee 4” q Gully trap Maser trap ½” G.I. Tee (1.25 cm) ½” G.I. Nipple Iron clamp 4” dia Bottle trap Waste water pipe 1 ¼” 3 lengths(3.25cm) Mason Kit 1 2 1 4 1 1 1 1 3 4 5 10 4 20 2 3 3 1 1 4 1 5 5 6 2 3 5

Norms for Accreditation-NIOS

SOLAR ENERGY TECHNICIAN (253)
1. The institution should have a minimum of one professional having a Degree (B.Sc. Ag.)/Diploma in Agriculture Engineering or Diploma in Mechanical/Civil/Electrical Engineering and having under gone elective course in non-conventional energy. A person with B.Sc./Intermediate with Science subject with two years of experience in installation & maintenance of Solar Energy plants may also conduct personal contact programmes, practical and skill tests. 2. A field visit to near by water solar installation is suggested. 3. For a batch size of 15 students, the following equipment and tools are required:

List of tools and equipment
Equipment /tools Solar intensity meter Heat exchanger Collector loop heater Solar intensity simulator Storage device (thermal) 24 cells Solar photovoltaic cells (system) 1panal 2’x2’ Transparent plastic sheet Solar cooker (domestic + community) Liquid flat plate collector Storage tank water Pump with motor Flow indicator Energy meter Motor and pump starter stop watch Solar controller Solenoid valve Control panel (optional) Quanti ty 1 1 1 1 1 1 set 10 1+1 1 1 1 1 1 1 2 1 2 1 Equipment /tools Water meter Solar dryer Glass cover Clay Conical solar water still distilled water G.I. pipe (size as per requirement) Water pan Velo meter Basin type solar distillation unit Tubular stationary 24 volt. 260amp battery Solar PV panel of 340 watt Invertors with 18 watt tube light Lead acid storage battery Solar water pumping system Electrical cable Delivery head pipe Quantity 1 1 4 As required 1 1 1 1 1

1 12 1 1 25 meter 2 ½ “-1 length as required Suction head pipe 2 ½ “-1 length as required Pyranometer to measure solar 1 intensity

Norms for Accreditation-NIOS

ELECTROPLATING (355)
1. 2. 3. The institution should have a workshop/work place of its own. Preferably the workshop should run as training cum production centre. The Institution should have a minimum of one professional having an I.T.I./Community Polytechnic/NIOS or equivalent certificate in electroplating trade. A person with B.Sc. or Diploma in Chemical engineering with two years experience in electroplating may also conduct personal contact programmes, practical and skill tests. For a batch size of 20-25 students, the following equipment’s and tools are required:

4. Sl. No.

List of tools and equipment
Equipment /tools 1. Canvas apron 2. Respirator 3. Goggles 4. Gum boots rubber Shop out fit Vice hand 50mmjaw File flat 200mm 2nd cut & File flat 200mm smooth Cutting Pliers insulated 200mm Bradawl Electrical –knife double bladed Quanti ty 5 5 10 3 pairs 2 2 each 2 2 2 20. 21. 22. 23. 24. 25. 26. 27. 29. 30. 31. 32. 33. 34 35. 36. Cleaning tank 100x60x45cm Gold plating vat enameled iron (small size) Grinder with high revolution emery wheel. Motor polisher (4 bearing type) Barrel plating outfit for nickel Burnishing set 150mm to 200mm Polishing barrel outfit for nickel Polishing barrel 45 x 90cm Dippling basket 200mm dia x 25mm Plating basket 45cm x 130cm Open ended plating barrel & Plating basket 45cm x 30cm x 130cm Plastic siphon 12mm dia Nickel comparator test set Jet test apparatus Buffing machine in spindle with meter bearing motored Plastic siphon 12mm dia Adjustable resistance board with voltmeter volt & ammeter. Suitable for each vat for voltage current control Electroplating rectifier three phase set to operate from 380/440 volts. 50 cycles, 3 phase a.c. supply 16 volts. d.e. with an out put of 500 amperes. dc. voltage adjustable from 3.5 to 16with 63 step on load, complete with the required meter panels and change over switch . Electric heater(silica lined )2 k.w. capacity. Electric heater (lead lined ) 2 k.w. capacity 1 1 1 1 1 1 1 each 1 1 1 each 1 1 1 1 1 9 nos.

1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16.

Leather chamois piece 50mm x 4 60cm Brush hand scratch 8 Bob felt 200mm & 16 Bob stitched 150mm dia each 16 each Dresser emery 1 Tong flat jaw 100mm length 4 Basin 300mm enamel 6 Glue pot 1 kg 1 nd cut half round 150mm File 2 4 Exhaust fans minimum 3 Vat for bright nickel plating lead lined 1 125cm x 100x60mm Dull vat for nickel plating lead lined 1 125x100x60cm Bright vat for chromium plating with outside water jacket 125x100x60cm Mop polishing & Mop dresser

37.

17. 18

40. 41.

Norms for Accreditation-NIOS

19.

Hard chrome plating vat with Antimonial lead lining with reinforced glass lining 125x100x60cum thermostat controlled attached with outside water jacket.

42.

PH meter

ELECTRICAL TECHNICIAN (701/702)
1. The institution should have a workshop/work place of its own. 2. The institution should have at least one professional with Diploma in electrical engineering or I.T.I. Certificate in electrical trade with 2 yrs Experience. 3. For a batch size of 20 students, the following equipment and tools are required:

List of Tools
Sl. No 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. Tools Plier insulted 150mm Screw Driver 150mm Electrician Knife Neon Tester Electrician connector screw driver Heavy duty screw driver 200mm Electrician screw driver 250mm Saw Tenon 250mm Firmer Chisel 12mm Pocker Plier flat Nose 150mm Centre Punch 150mm x 9mm Electric drill machine (portable) 12mm capacity Oil can 0.12 litre Grease Gun (small) Standard wire gauge Bering Puller Scissors 150mm blade Quantit y 5-10 set 5-10 set 5-10 set 5-10 set 5-10 set 5-10 set 5-10 set 5-10 set 5-10 set 5-10 set 5-10 set 5-10 set 5-10 set 5-10 set 5-10 set 5-10 set 5-10 set 5-10 set Sl. no 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. Tools Drill S.S. Twist 3mm, 5mm, 6mm File (flat) 200mm 2nd cut File (round) 200mm 2nd cut File (half round) 200mm 2nd cut Soldering Iron 125 watts Soldering Iron 65 watts Bench Vice 100mm Jaw Hacksaw plug tool set 8 to 4 No. Rawal Plug tool set 8 to 4 No. Cold chisel 12mm x 200mm flat Hand drill machine 0 to 6 mm capacity Tri square 150mm Pipe vice 50mm Pipe wrench 0-50mm Ball pin hammer 100gm, 500gm & 1kg. Hand drill machine Micrometer 0-100mm Quantit y 5-10 set 5-10 set 5-10 set 5-10 set 5-10 set 5-10 set 5-10 set 5-10 set 5-10 set 5-10 set 5-10 set 5-10 set 5-10 set 5-10 set 5-10 set 5-10 set 5-10 set

Norms for Accreditation-NIOS

List of Instruments and equipment
Sl. No 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Quantit y Ammeter 0-1, 0-3, 0-5, 0-10 & 0- 2 each 30amps Voltmeter 0-600 VMI & Voltmeter 0- 1+1 500 V M C Megger (Insulation tester) 500 V Multimeter (digital) Heater-ordinary one K.W. & Room Heater Rod Type one K.W. Electric Iron (Automatic with opne element) 220V-750 watts Electric Iron steam 220V-1000 watts Electric toaster (ordinary) Geyser (storage)2KW Kettle ordinary 500 watts Kettle automatic 1000 watts Heat Convector 220 volts 1000 watts Voltage stabilizer –Automatic 1440 R.P. i) Single phase transformer step up ii) Single phase transformer step down iii) Three phase transformer step up iv) Three phase transformer step down A.C. three phase sq. cage 24 slots pole motor A.C. Three phase sq. cage 36 slots pole motor A.C. Single phase capacitor type motor A.C. Universal (Series) motor single phase A.C. Ceiling fan motor A.C. Table fan motor A.C. Cooler motor 1 1 2+2 2 2 2 1 1+1 1+1 4 Instruments & Equipment Sl. no 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. Instruments & Equipment A.C. Cooler pump motor A.C. Mixer motor A.C. Monoblock pump 2800 R.P.M. ½ H.P./One H.P. Hair Drier O.T.G - One Charge over switch (Manual) Charge over switch (Automatic) Installation inverter Washing machine (Manual) Generator Alternator Clip on Meter Digital 0-200Amp. Water Meter Single phase 1KW220V Single Phase energy meter (K.W.H.) 5-10Amp. 220V Three phase energy meter (3phase 4 wire) 10-20 Amp. 440 V quantit y 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

13. 14. 15. 16. 17. 18. 19.

1 1 1 1 1 1 1

33. 34. 35. 36. 37. 38. 29.

Frequency meter 0-60 Hz. Double Element Hot Plate Micro meter 0-50 mm 3 phase DOL starter 440V – 20Amp. D.C. 3 point starter 220V, 020Amp. D.C. 4 point starter 220 V, 020amp. Winding Demonstration board of 24 slots/36 slots 4 pole/ 6 pole

1 1 1 1 1 1 1

Norms for Accreditation-NIOS

RADIO & T.V. TECHNICIAN (703/704)
1. The institution should have a workshop/work place of its own. 2. The institution should have at least one professional with Diploma in Electronics or I.T.I Certificate in Electrical trade with 2 yrs Experience. 3. For a batch size of 20 students, the following equipments and tools are required:

List of tools
Sl. No 1. 2. 3. 4. 5. 6. 7. Tools Screw driver sets Combination pliers Diagonal cutting pliers Long nose pliers Hand drills Hacksaw Soldering Iron 10W, 60W & 250W Quantity 5-10 Set 5-10 Set 5-10 Set 5-10 Set 5-10 Set 5-10 Set 5-10 Set Sl. no 8. 9. 10. 11. 12. 13. Tools Adjustable wrench set Ball peinhammer Allen keys set Neon Tester Double ended spanner sets Hammer cross pein 100gm Quantity 5-10 Set 5-10 Set 5-10 Set 5-10 Set 5-10 Set 5-10 Set

List of Instruments and equipments
S. no 1. 2. 3. 4. Instruments & Equipment AM Radio receivers 2 band, FM Radio receivers Cassette Tape recorder Black & white TV set Portable with remote Colour TV sets with remote Quantit S. no y 2+2 12. 2 13. 1 14. 1 15. Instruments Equipment High Voltage Probe TV Antenna Voltage stabilizer Antenna Booster (optional) for remote areas where signals are weak Extension Boards Milli Vott Millilvolt meter Power Meter 250V, 150 Mobile – Audio & Video CD player & recorder FM Unserviceable Radio, T.V., Tape Recorder sets (Tools) & Quantit y 1 1 1 2

5. 6. 7. 8. 9. 10 11.

Multimeters Digital Multimeters R.F. Signal Generator Oscilloscope 15 MHz Pattern Generator Colour Ban generator Audio Signal Generator

2 16. 2 1 1 1 1 1 17 18 19. 20. 21. 22.

5 1 1 1 1 1 5 sets each

Norms for Accreditation-NIOS

REFRIGERATION & AIR CONDITIONING TECHNICIAN (709/710)
1. The institution should have a workshop/work place of its own. 2. The institution should have at least one professional with Diploma in Mechanical Engineering /Air Conditioning/Refrigeration or I.T.I./NIOS/Community Polytechnic Certificate in Refrigeration and Air Conditioning trade with 2 yr. experience. 3. For a batch size of 15 students, the following equipment and tools are required:

List of tools and equipment
Sl. no 1. 2. 3. 4. Tools Flaring tool set Tube cutter Swaging tool set Gasket punch set quantit Sl. y no 13. 5 14. 5 5 5 15. 16. 17. quantit y Multi meters digital 02 Gas cylinder F-12-2kg & F-22-2kg 01 capacity, R-134A-1 Hydro Carbon, each ISO butane/ ISO propane Air Blower 01 Dry Nitrogen cylinder 01 Voltage stabilizer –4 KVA 1 each - Gas charging & evacuation Unit –1 - Voltage stabilizer (desirable inverter/generator) 1KVA – 1 - Clamp meter (Tong tester) for current detection –1 Soldering Iron 50, 20, 15 & 10 watt 1 each Equipment Open type compressor Sealed type compressor 02 02 tools

5. 6. 7. 8. 9. 10. 11. 12.

Tube bender –spring type – mechanical type Cylinder Valve key & Spring key Pinching Pliers & Pinching tool Amp meter 0-5 amps & Amp meter 0-30 amps Thermometer F & C Vacuum pump Gas charging line

5 5 5 each 2+2 2 each 2 2

18. 19. 20. 21. 22. 23. 24.

Pressure gauge & Compound 2 gauge

Old Refrigerator for demonstration/Practical 02 Old Window type air conditioner for 02 demonstration/Practical Old water cooler for 02 demonstration/practical Water purifiers 01

Norms for Accreditation-NIOS

PLUMBING (611)
1. The Institute should have at least one professional with Diploma in Civil/Mechanical Engineering or I.T.I. certificate in plumbing trade 2. For a batch size of 20 students, the following equipment’s and tools are required. 3. The institution should have a workshop/work place of its own.

List of tools and equipment’s
Sl. no 1. 2. 3. 4. 5. 6. 7. 8. Tools W.C. (Indian type) W.C. (European Type) L.L. cistern H.L cistern Automatic cistern Urinal Basin Wash Basin Sink Quanti ty 05 05 05 05 05 05 05 05 Sl. no 9. 10. 11. 12. 13. 14. 15. 16. Tools C.I. Trap (Nahani) Check Valve ½” Ferrule ½”=1” Flush pipe G. I. Bend Grating Brass Bib Cock Brass stop Cock Quanti ty 05 05 05 05 05 05 05 05

Sponsor Documents

Or use your account on DocShare.tips

Hide

Forgot your password?

Or register your new account on DocShare.tips

Hide

Lost your password? Please enter your email address. You will receive a link to create a new password.

Back to log-in

Close