Testosterone Preparation
Content
Testosterone enanthate : Method 1: The best metbkdm[fof You will need benzyl alcohol, syringes, a container that will hold 20 ml and oil (arachis or sesame oil). Because we will inject this, the oil needs to be sterile. To sterilize it heat the oil to 212 degrees F (100 degrees C). In the mean time use a syringe to fill your container with EXACTLY 20 ml of pure water. Mark the container at the water level. use the syringe to take out 0.6 ml and make another mark. Your container is now marked at 19.4 ml and 20 ml. Dump out the water and let the container dry. let the oil cool off. Dump the powder (5 g) in the container, add oil until it reaches the 19.4 ml mark. Then add Benzyl alcohol until it reaches the 20 ml mark. Seal your container and shake it well. You are now ready to use the product. It is a testosterone enanthate solution at 250 mg/ml. I suggest two weekly injections of 0.6 ml (175 mg) for a period of 10 weeks. At this rate the product will last you exactly 10 weeks. Method 2: Bulk Production, evmgi Testosterone enanthate, 500 grams (will only use 250g max) Nalgene® MF75 bottle top filters (45mm, 500mL, .2µm) with Pall Supor® machV PES Membrane Beaker (either 500mL or 1,000mL) (Bomex) 500mL Pyrex glass media bottle, 45mm top Electric stove 60mL syringes 50mL sterile vials Benzyl alcohol Funnel 0.1g scale, 500g max capacity Spoon Grape seed or maybe walnut oil (need to get) Brake bleeder vacuum kit (need to get) Temperature resistant cloth to pick hot beaker off of stove (what are these called)
Making small amount first. Say, 50mL at 400mg/mL. (20 Grams Test E.) Use 60mL syringe and water to verify and mark where 50mL is on the beaker and the media bottle. Measure out 20g of test enan into beaker using scale Add 50mL*2%=1mL BA to beaker Add oil to the beaker until it is a little less than the 50mL line Place beaker in center of electric burner on stove. Beaker will be directly on the element Turn on, medium-low heat Do not go get beer or get distracted. Watch the oil. At it warms, stir with spoon. When all hormone is dissolved, remove from heat Oil is hot. Let stand for five minutes Attach bottle top filter to media bottle. Attach vacuum. Pour oil from beaker into bottle top filter and cap Vacuum pressure of 10 Hg Wait for oil to filter
Eliminate vacuum pressure Add plain oil to the bottle top filter to make up for whatever needs to be added so that there is 50mL in the media bottle. This will flush remaining hormone in the bottle top filter into the media bottle. Wait for the remaining oil to filter Eliminate vacuum pressure Vent vial with pin Stick 60mL syringe into vial, remove plunger, insert funnel Pour 50mL of oil from media bottle into syringe using funnel Remove funnel, replace with plunger. Inject oil into vial Get beer
Making small amount first. Say, 50mL at 400mg/mL. (20 Grams Test E.) Use 60mL syringe and water to verify and mark where 50mL is on the beaker and the media bottle. Measure out 20g of test enan into beaker using scale Add 50mL*2%=1mL BA to beaker Add oil to the beaker until it is a little less than the 50mL line Place beaker in center of electric burner on stove. Beaker will be directly on the element Turn on, medium-low heat Do not go get beer or get distracted. Watch the oil. At it warms, stir with spoon. When all hormone is dissolved, remove from heat Oil is hot. Let stand for five minutes Attach bottle top filter to media bottle. Attach vacuum. Pour oil from beaker into bottle top filter and cap Vacuum pressure of 10 Hg Wait for oil to filter
Eliminate vacuum pressure Add plain oil to the bottle top filter to make up for whatever needs to be added so that there is 50mL in the media bottle. This will flush remaining hormone in the bottle top filter into the media bottle. Wait for the remaining oil to filter Eliminate vacuum pressure Vent vial with pin Stick 60mL syringe into vial, remove plunger, insert funnel Pour 50mL of oil from media bottle into syringe using funnel Remove funnel, replace with plunger. Inject oil into vial Get beer
