Train collision avoidance using vibration sensor

Published on February 2017 | Categories: Documents | Downloads: 22 | Comments: 0 | Views: 166
of 4
Download PDF   Embed   Report



Train Collision Avoidance Using Vibration Sensor & Micro-Controller
There is an increasing with the number of accidents at railroad railings. Collisions with train are generally catastrophic, in that the destructive forces of a train usually no match for any other type of vehicle. Train collisions form a major catastrophe, as they cause severe damage to life and property. Train collisions occur frequently eluding all the latest technology. This paper deals about one of the efficient methods to avoid Train Collisions. This approach uses the Vibration sensor and a Proximity LASER Detector and the communication mechanism of PLC (Power Line Communication) to communicate the Critical Details about the Train to the Control Room.

Problem Definition
Train Collisions are of different types depending upon the circumstance. The head to head collisions are nowadays mostly avoided with the advancement in the technology. Anti Collision Devices have knowledge embedded intelligence.
They take inputs from GPS satellite system for position updates and network among themselves for exchanging information using their data radio modems to take decisions for timely auto-application of brakes to prevent dangerous ' head to head collisions' . so we have to focus on the other potential reasons for the dangerous mishap or catastrophe. The other main

reasons for the collisions of Train are: 1.Train Derailment in curves and bends,2.Running Train collisions with the Standing Train,3.Train Accidents in Slopes,4.Mis- signalling due to fog or Mist. Micro-controller and the embedded technology is used in the coherence of the above operation with the sensors and relays and solenoid valves as electromechanical switches. h Te Embedded technology has reached its peak so that the design can be so perfect with time critical parameters.

Figure 1. Gap Detector

Details about the problem
The avoidance problem in this paper has been split into individual blocks and then joined together with time factors for the complete solution. Bottom to top approach is used. The different blocks used to avoid the Collisions by above mentioned reasons are: 1.Gap Detector, 2.Vibration Sensor, 3.Proximity LASER Detector, 4.LED lighting or Fog penetrating Lights, 5.FSK Modulator and FSK Demodulator (For Power Line Communication) .A Microcontroller for entire Control. The Microcontroller is interfaced with the input sensing devices such as vibration sensor, Gap Detector and proximity LASER Detector. 1. Gap Detector: Figure 1. Gap Detector In bends or curves, there should be gap between the rails of successive different paths. Even if there is a small gap, the train would get mislead and travel in a different path which leads to collisions in most of the cases. Already there are sensors to indicate the short circuiting of the gaps but practically even a small dust can short circuit the gap which makes the current system futile sometimes. Hence we use adjustable mechanical or elastic claw to find the gap and indicate the gap immediately to the Control Room. In the above figure, a rail road indicating a gap and next to it is a Electrostatic; capacitance-type Gap Detector : VE Series. 2. Vibration Sensor: It uses piezoelectric effect to detect the vibrations in the rails due to the arrival or departure of train and the direction of vibration indicate the arrival or departure. This could sense the train s position at roughly at 800 to 900 m away. This input is fed to the microcontroller. This could help in avoiding accidents between trains in slopes because the arrival of one train found out using vibration sensor can be immediately sent to the Control Room and the power supply can be switched off within 3 minutes so trains could be stopped without colliding each other. Vibration or shock sensors are commonly used in alarm systems to activate an alarm whenever the devices to which they are attached are touched, moved, or otherwise vibrated. Commercial vibration sensors use a piezoelectric ceramic strain transducer attached to a metallic proof mass in order to respond to an externally imposed acceleration. Piezoelectric vibration sensors used for detecting vibration from various vibration sources are generally classified into

two large types, resonant type and nonresonant type.

Figure 2. An Example of Piezo-electric Vibration Sensor 3. Proximity LASER Detector: Most of the collisions are of running train colliding with the Standing Train Types. A LASER detector can be used to detect the presence of any train before the running train. D A laser proximity sensor for a train includes a laser diode having front and rear facets. The diode generates a main laser signal and directs a first portion thereof out of the front facet as a source beam. Focusing means focuses the source beam on a target, and focuses the return beam reflected from the target into the laser diode through the front facet. The laser diode receives the return light beam, provides it with a positive gain, mixes it with the main laser signal, and guides it out the rear facet as a mixed beam. A detection focusing device focuses the mixed beam onto a PIN detector. The PIN detector coherently detects the mixed beam and provides an output signal having a perturbation where the target enters the focal field of the focusing optics. A processor detects the output signal from the PIN detector and may activate a breaking mechanism in the train. The processor is also capable of determining the relative velocity between the train and the target from measurement of the Doppler shifted signal or from the shape of the perturbation of the output signal from the PIN detector.

Figure 3. LASER Proximity Detector – setup

4.LED or Fog penetrating Lights are very useful during mist or fog seasons, as, near the signals, still many employees use explosives or other form of lights which involves the manual monitoring next to the signal 24*7. So, detecting the arrival of signal using Vibration Sensor, the LED lights can be made to switch off automatically in the signals reducing the manual labour and monitoring and the driver from the train could get the signal easily even in fog times Any given snowy, foggy or rainy night can turn into a disaster because low visibility in these conditions can maximize the potential of danger. Rough weather conditions call for precision driving, Using and installing fog lights can help signals be seen better. 5.FSK Demodulation and Modulation:Power line communication(PLC), also called power line carrier, mains communication, power line telecom(PLT), or power line networking (PLN) are terms describing several different systems for using electric power lines to carry information over the powerline. Data rates over a power line communication system vary widely. Low-frequency(about 100-200 KHz) carriers impressed on high-voltage transmission lines may carry one or two analog voice circuits, or telemetry and control circuits with an equivalent data rate of a few hundred bits per second; however, these circuits may be many miles(kilometres) long.

Details about the set applied:

Figure 4. Layout section
1.Vibration Detector - Train arrival Microcontroller Control Room Power off Stopping of Train This vibration detector helps to prevent head on collisions as well as train derailment and during mist conditions. 2.Proximity LASER Detector Standing Train Detector MicroController Jamming the Brakes or Sending info to Control Room Power off Stopping of Train This operation helps to prevent the collision of running train over the Standing train 3.Gap Detector Gaps in Bends or Curves Info about Trains path -1. Correct Path No problem 2. Wrong Path .Microcontroller Jamming the brakes or Sending info to Control Room Gap Correction or Power off Stopping of Train

Figure 5. Gap between the rails Small gaps may lead to disaster misleading the train in different direction. 4.Vibration Sensor Train Arrival Mist of Fog Times Microcontroller Automatic Switching of LED lights or Fog penetrating Lights Microcontroller Control Room Communication 5.Microcontroller FSK Modulator Main Transmitter PLCC Main Receiver FSK Demodulator PC in Control Room

All power line communications systems operate by impressing a modulated carrier signal on the wiring system. Different types of powerline communications use different frequency bands, depending on the signal transmission characteristics of the power wiring used. Since the power wiring system was originally intended for transmission of AC power, in conventional use, the power wire circuits have only a limited ability to carry higher frequencies. The propagation problem is a limiting factor for each type of power line communications. A new discovery called ELine that allows a single power conductor on an overhead power line to operate as a waveguide to provide low attenuation propagation of RF through microwave energy lines while providing information rate of multiple Gbps is an exception to this limitation.

Result and Discussion The sensors sense the input and sends to the microcontroller, where it responds and gives command to the particular component with predefined algorithm. The time parameters are crucial which can be easily changed and modified using Micro-controllers. Thus, this device would work in coherence would help to reduce the train collisions. Summary
ACCIDENTS involving trains are gruesome. There s the magnitude of the loss involved, both of life and property, and the trauma it causes to the families of the passengers on board.In railway operations, it is the driver who is virtually driving blind in the block section because his vision does not cover the braking distance of a train, and only at stations does he have signals to guide him. A simple misjudgement of the colour of a signal at a station can lead to a major mishap, notwithstanding the huge investment made in wiring the signals. Many a time, trains on the same lines have collided head-on and caused hundreds of passengers to lose their lives. Thus this idea can improve the safety of Train system. This idea can be a base and future modifications can be made for an optimised and sophisticated system. Future Directions The Anti Collision Device (ACD) is a self-acting microprocessor-based data communication device designed and developed by Konkan Railway (KR). When installed on locomotives (along with an auto braking unitABU), guard vans, stations and level-crossing gates (both manned and unmanned), the network of ACD systems prevents high-speed head on collisions in mid-sections, station areas and at level-crossing gates, thereby saving the lives of rail passengers and road users. This device can be integrated with the Anti Collision Device for better sophistication and optimisation. References Case Study made in North Coimbatore Railway Control Room. Collision Avoidance Systems Vibration Sensors; Raksha Kavach Anti Collision Devices. Collision Avoidance Using GPS Device and Train Proximity Detector


Sponsor Documents

Or use your account on


Forgot your password?

Or register your new account on


Lost your password? Please enter your email address. You will receive a link to create a new password.

Back to log-in